2. Concept2
  3. RowERG
RowERG

Concept2 RowERG User manual

  • Hello! I've analyzed provided assembly instructions document for Concept2 RowErg. This document includes detailed steps for assembling the RowErg and instructions for tall legs retrofit. The document notes the device's weight limits and space requirements, and also shows how to use a device holder. I'm ready to answer any questions you might have about the assembly process.
  • What is the weight capacity of the RowErg?
    What are the space requirements for using the RowErg?
    Where can I find the parts list for the tall legs retrofit?
0522
1
BOX 2
WITH TALL LEGS
BOX 1
Weight: 68 lb (31 kg)
Dimensions: 8 ft x 2 ft (244 cm x 61 cm)
Space Required for use: 9 ft x 4 ft (274 cm x 122 cm)
Weight Capacity: 500 lb (227 kg) as tested by Concept2*
*300 lb (135 kg) as tested per European Stationary Fitness
Equipment Testing Standard EN 20957-7
PN 2453
PN 7109
PN 2960
ASSEMBLY INSTRUCTIONS
ROWERG WITH TALL LEGS ASSEMBLY - PAGE 2
TALL LEGS RETROFIT - PAGE 4
Not to scale x 8
3/4” (1.9 cm)
PN 2233
T-27 DRIVER
PN 2230
x 4
5/8” (1.58 cm)
PN 2395
*
x 4
PN 2394
*
Note: There will be two remaining PN 2395 and two remaining PN 2394 after
completing RowErg Assembly. ALL hardware will be used for Tall Legs Retrofit.
RowErg Assembly & Tall Legs Retrofit
RowErg Assembly
c2vt.com/rowassembly
Questions? Comments? Problems?
Contact Concept2 directly at 800.245.5676 (US and Canada)
Or visit us online: concept2.com
Concept2, Inc. 105 Industrial Park Drive Morrisville, Vermont USA 05661 concept2.com/contact
®
BAG 2952 BAG 2331
+ =
from step 3
34
56
IMPORTANT
Two screws and
two nuts will be
reinstalled in step 6.
WITH TALL LEGS ASSEMBLY INSTRUCTIONS
12
(4) 3/4” (1.9 cm)
PN 2233
(4) 3/4” (1.9 cm)
PN 2233
reuse in step 4
ASSEMBLY TIP
Do not fully
tighten screws
until all screws
are in place.
(4) 5/8” (1.58 cm)
PN 2395
(4) PN 2394
2RowErg with Tall Legs Assembly instructions
7
WITH TALL LEGS ASSEMBLY INSTRUCTIONS
How to Use the Device Holder
Insert
device
Pinch and
release to
remove
device.
Loosen knob
to slide lower
bracket up or
down.
Important:
Tighten knob
when device
is in place.
3RowErg with Tall Legs Assembly instructions
4
TALL LEGS RETROFIT INSTRUCTIONS (Refer to page 1, “Box 2” for parts list)
3
2
(4) 3/4” (1.9 cm)
PN 2233
(4) 3/4” (1.9 cm)
PN 2233
4
56
1
ASSEMBLY TIP
Do not fully
tighten screws
until all screws
are in place.
7/16” Socket Wrench
Not Included
*reuse in
step 4
X
X = do not reuse
X
X
*
X
X
ASSEMBLY TIP
Do not fully
tighten screws
until all screws
are in place.
(4) 5/8” (1.58 cm)
PN 2395
(4) PN 2394
Tall Legs Retrot Instructions
X
+ =
from step 1
/