Sunco Lighting PRE-01009 48 Installation guide

Brand: Sunco Lighting

Model: PRE-01009 48

Type: Installation guide

Sunco Lighting PRE-01009 48" offers adjustable wattage, allowing you to customize the brightness to suit your needs. With a wide range of 80W to 150W, you can effortlessly set the desired ambiance. This canopy light is suitable for both ceiling and surface mount installations, providing versatility in placement. Its durable construction withstands temperatures ranging from -40° to 104°F, ensuring reliable operation in various environments.

LED CANOPY • 120-277V

INSTALL INSTRUCTIONS

Specifications subject to change without notice. Photos and line

drawings may not be to scale and are for general reference only.

!WARNING DISCONNECT POWER BEFORE INSTALLING OR SERVICING.

PLEASE FIND A QUALIFIED ELECTRICIAN FOR INSTALLATION. Please read the instructions before you install and use the luminaire.

•To avoid the risk of fire, explosion, or electric shock, this product should be installed, inspected, and maintained by a qualified electrician only, in

accordance with the national electric code (NEC) and all applicable federal, state and local electric codes and safety standards.

• To avoid electric shock or component damage disconnect power before attempting installation or servicing.

•Luminaire must be connected to a wiring system with an equipment-grounding conductor.

• This luminaire is designed to operate in ambient temperatures ranging from -40° to 104°F (-40 to 40°C).

•Make sure the supply voltage is the same as the rated luminaire voltage; 120-277V AC • 50/60Hz • Input current 1.8A Max.

•Do not install where the marked operating temperatures exceed the ignition temperature of the hazardous atmosphere.

•Do not operate in ambient temperatures above those indicated on the luminaire nameplate.

• Suitable for wet locations.

•For supply connections use wire rated for at least 100°C.

Note: Save these instructions for future reference.

TROUBLESHOOTING

• Check that the fixture is firmly secured to the mounting surface.

• Verify the proper line voltage is present and the fixture is wired correctly.

• Check that the fixture is grounded.

CEILING MOUNT

1. Use the existing hole in the ceiling or open a 1 ¾” hole. (Fig. 1)

2. Put the back thread through the hole, secure it by the gasket, plate and hex head

locknut. Make sure there is no gap between the plate and ceiling. (Fig. 2)

3. Tighten the small set screw on the side of the locknut to prevent from loosening. If the

mounting surface was not flat, sealant should be applied surround the plate and each

screws. (Fig. 3)

4. Use a 3/4” conduit to lead out the wires. Connect the luminaire wiring to line wires

with UL approved connectors; Live to Black, Neutral to White and Ground to Green.

(See General Wiring Connections)

Ceiling

1 ¾” Hole

Fig. 1 Fig. 2 Fig. 3

Locknut

Mounting Plate

Gasket

Ceiling

¾” - 14T Thread

GENERAL WIRING CONNECTIONS

Black

Light

Fixture

(L) Live Line

Green(G) Ground Line

White(N) Neutral Line

LED CANOPY • 120-277V

INSTALL INSTRUCTIONS

Specifications subject to change without notice. Photos and line

drawings may not be to scale and are for general reference only.

FIELD ADJUSTABLE WATTAGE (If applicable)

The end users may adjust the wattage/brightness, respectively, by

the DIP switches on the side of the fixture. Unscrew the knob cap

before using the watt selectable function. Referencing the watt

selectable label shown in Fig. 7, toggle each DIP switch (1, 2, 3) to

select the desired watts. Replace knob cap.

Threaded Adapter

¾” - 14T Thread

Potentiometer

Ceiling

Fig. 5 Fig. 6

16”

14 ⅜”

14 ⅜” 16”

Clear Glass

Fig. 4

SURFACE MOUNT ON JUNCTION BOX

1. Drill holes in the ceiling according to the dimensions in Fig. 4.

2. Remove the threaded adapter from the back of fixture. (Fig. 5)

3. Connect the luminaire wiring to line wires with UL approved connectors; Live to Black, Neutral to White and Ground to Green. (See General Wiring

Connections)

4. Secure the fixture to the roof with 4 screws. (Fig. 6)

SURFACE MOUNT WITHOUT JUNCTION BOX

1. Drill holes in the ceiling according to the dimensions in Fig. 4.

2. Remove the threaded adapter from the back of fixture. (Fig. 5)

3. Open the back plate, pull the wires back and through out from the 1/2” NPT threaded hole. Secure the fixture to the roof with 4 screws. (Fig. 6)

4. Connect the luminaire wiring to line wires with UL approved connectors; Live to Black, Neutral to White and Ground to Green. (See General Wiring

Connections)

5. Sealant should be applied surround the 1/2” hole.

Knob Cap

Fig. 7

150W

1 2 3

120W

1 2 3

100W

1 2 3

80W

1 2 3

Dip switch positions are in white.

Sunco Lighting PRE-01009 48 Installation guide

Sunco Lighting PRE-01009 48 Installation guide

Sunco Lighting PRE-01009 48 Installation guide

Related papers

Other documents