OpenEye OE-C7094-AWR User guide

OE-C7094-AWR
Brand
OpenEye
Model
OE-C7094-AWR
Category
Security device components
Type
User guide

OpenEye OE-C7094-AWR is a high-resolution IP bullet camera designed for professional surveillance applications. With its 4MP resolution and 20FPS frame rate, it delivers crystal-clear and smooth video footage. The camera features true day/night functionality and wide dynamic range (WDR), ensuring excellent image quality even in challenging lighting conditions. It also supports ONVIF Profile S and G, making it compatible with a wide range of surveillance systems. The OE-C7094-AWR is built tough with an IP67 rating for water and dust resistance, and an IK10 rating for vandal resistance.

OpenEye OE-C7094-AWR is a high-resolution IP bullet camera designed for professional surveillance applications. With its 4MP resolution and 20FPS frame rate, it delivers crystal-clear and smooth video footage. The camera features true day/night functionality and wide dynamic range (WDR), ensuring excellent image quality even in challenging lighting conditions. It also supports ONVIF Profile S and G, making it compatible with a wide range of surveillance systems. The OE-C7094-AWR is built tough with an IP67 rating for water and dust resistance, and an IK10 rating for vandal resistance.

Copyright ©2021 OpenEye.
All Rights Reserved. Information contained in this document is
subject to change without prior notice. OpenEye does its best to
provide accurate information but cannot be held responsible for
typos or mistakes.
Liberty Lake, WA, USA
509.232.5261
openeye.net
1
2
QUICK START GUIDE
OE-C7094-AWR / 4MP IP Bullet Camera
OE-C7098-AWR / 8MP IP Bullet Camera
This quick start guide provides only basic information on the camera’s settings
and operation for initial installation. Please read the user manual for optimal
camera confi gurations.
35562AH openeye.net
CONNECTIONS
Waterproof Cable
1
1
Thread lock cap
Thread lock cap
4
4
Rubber “O” ring
Rubber “O” ring
2
2
Rubber plug
Rubber plug
5
5
Camera cable
Camera cable
3
3
RJ45 enclosure
RJ45 enclosure
5431
2
1
1
RJ-45
RJ-45
For network and PoE connections
For network and PoE connections
2
2
BNC
BNC
For analog video input
For analog video input
3
3
Power (12vDC)
Power (12vDC)
Power connection
Power connection
4*
4*
Audio In/Out
Audio In/Out
Audio Out is reserved
Audio Out is reserved
5*
5*
Alarm I/O
Alarm I/O
Blue
Blue
Ground
Ground
Brown
Brown
Alarm Input
Alarm Input
Green
Green
Alarm Out -
Alarm Out -
Orange
Orange
Alarm Out +
Alarm Out +
1
1
Reset Jumper
Reset Jumper
To restore the camera to factory
To restore the camera to factory
defaults:
defaults:
1. Disconnect power for 30
1. Disconnect power for 30
seconds.
seconds.
2. Reconnect power and wait 30
2. Reconnect power and wait 30
seconds.
seconds.
3. Close the jumper connection
3. Close the jumper connection
with a proper tool for 20 seconds.
with a proper tool for 20 seconds.
2
2
MicroSD Card
MicroSD Card
Slot
Slot
Supports up to 128GB microSD
Supports up to 128GB microSD
card for Edge storage.
card for Edge storage.
Do not add or remove the microSD
Do not add or remove the microSD
card when the camera is powered
card when the camera is powered
on.
on.
1
Brown
Brown
Orange
Orange
Green
Green
Blue
Blue
In
In
Out
Out
POWER
This camera is compatible with 12vDC
and Power over Ethernet (PoE). If you
are connecting 12vDC power, verify the
polarity of the power connection.
CONTENTS
ETHERNET CABLE
CONNECTIONS
Connect a network cable to the camera
using the RJ45 input and connect the
other end of the cable to your network
switch or recorder.
INSTALLATION
1. Apply template sticker to desired
camera location.
2. Drill anchor holes using included
mounting template.
3. Remove mounting template.
4. Insert anchors.
5. Mount camera.
6. Connect network cable with
included waterproof cable
connector.
7. Adjust camera view.
NOTE: If the camera will be exposed
to inclement weather, OpenEye
recommends sealing around the camera
base, or connection to accessory and
accessory connection to mounting
surface with outdoor waterproff
caulking.
NOTE: Refer to your Apex recorder manualor
quick start guide for instruction on
adding cameras. Passwords must be
9-32 characters including at least two
elements of the following three: digits,
letters, and special characters.
NOTE: To change this IP address please refer to
your Apex recorder manual.
NOTE: NCM requires entry in all fi elds
ASSIGNING AN
IP ADDRESS
OpenEye IP cameras are set to DHCP
by default. If a DHCP server is not
detected after 4 minutes, the camera
will default to IP address 192.168.51.2.
If you are not using a DHCP server,
NCM will allow you to batch confi gure a
static IP address.
The IP address for the camera network
on your Apex recorder is 192.168.51.1.
OE-C7094/8-AWR
Bullet Camera
PRODUCT FEATURES
Camera
Model OE-C7094-AWR OE-C7098-AWR
Maximum
Resolution 2592x1520 3840x2160
Frame Rate at
Maximum
Resolution
20FPS 15FPS
ONVIF ONVIF Profi le S / G Compliant
Day/Night True Day / Night
Wide Dynamic
Range True WDR
Environmental and Power
Model OE-C7094-AWR OE-C7098-AWR
Power
Consumption 9W Max
Input Voltage 12vDC ±25% / PoE
Operating
Temperature -31°~140°F (-35°~60°C )
IP Rating IP67
Vandal
Resistance IK10 Rated
Waterproof
Cable
Self-Tapping
Screws &
Plastic Anchors
Quick Start
Guide
Mounting Template
Selecting multiple cameras and enter-
ing IP address 192.168.51.2 will set an
IP address on all selected cameras,
starting at 192.168.51.2 and increase
per camera.
1. Open Network Camera Manager.
2. Select applicable camera(s).
3. Input starting IP address, Subnet
Mask, Gateway, DNS.
4. Apply changes.
5. Wait 60 seconds before refreshing
NCM.
NOTE: OpenEye IP cameras ship
without a default password.
DEFAULT USERNAME
AND PASSWORD
The admin user password can be set
using the following methods:
1. OpenEye recorders running Apex
2.1 or newer will automatically set
a new unique password if:
• Connected to an M-Series
recorder with a built in PoE
switch.
• Connected to a network
switch through the
camera network port
and selected then added in
setup, if a new password has
not already been set.
2. Connect to the camera directly
through a Web Browser and follow
the onscreen prompts.
3. Use the Network Camera Manager
(NCM) Utility.
Username: admin
NOTE: The NCM software manual can be
found at https://www.openeye.net/
ncm-manual
CONNECTING TO THE
IP CAMERA
To access the camera setup menu,
you need to open Network Camera
Manager (NCM) utility. NCM is pre-
installed on all OpenEye Recorders,
and is also available for download on
the OpenEye website for installation on
your personal computer or laptop.
1. Open Network Camera Manager.
2. Locate your camera on the
Network Camera Manager list.
3. To open the web browser, select
the camera and click LOAD.
  • Page 1 1
  • Page 2 2

OpenEye OE-C7094-AWR User guide

OE-C7094-AWR
Brand
OpenEye
Model
OE-C7094-AWR
Category
Security device components
Type
User guide

OpenEye OE-C7094-AWR is a high-resolution IP bullet camera designed for professional surveillance applications. With its 4MP resolution and 20FPS frame rate, it delivers crystal-clear and smooth video footage. The camera features true day/night functionality and wide dynamic range (WDR), ensuring excellent image quality even in challenging lighting conditions. It also supports ONVIF Profile S and G, making it compatible with a wide range of surveillance systems. The OE-C7094-AWR is built tough with an IP67 rating for water and dust resistance, and an IK10 rating for vandal resistance.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents