KUZCO PD88118 User manual

Type
User manual

KUZCO PD88118 is a ceiling LED pendant light fixture that combines modern design with energy-efficient LED technology. It features adjustable wire length, allowing you to customize the height of the fixture to suit your space. The fixture comes with pre-wired LED modules and is compatible with ELV (Electronic Low Voltage) or TRIAC dimmers for dimming control. Installation requires a qualified licensed electrician and should be done according to the provided instructions. Please refer to the installation sheet for detailed steps and safety precautions.

KUZCO PD88118 is a ceiling LED pendant light fixture that combines modern design with energy-efficient LED technology. It features adjustable wire length, allowing you to customize the height of the fixture to suit your space. The fixture comes with pre-wired LED modules and is compatible with ELV (Electronic Low Voltage) or TRIAC dimmers for dimming control. Installation requires a qualified licensed electrician and should be done according to the provided instructions. Please refer to the installation sheet for detailed steps and safety precautions.

19054 28th Avenue Surrey, BC Canada V3Z 6M3
T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196
W: kuzcolighting.com
INSTALLATION SHEET
PD88118
Ceiling LED Pendant
1a.
1b.
1c.
1f.
1g.
1e.
1. Remove fixture from its original package
2. Separate mounting plate (1c) from canopy (2a) by
removing canopy screws (2b)
3. Attach mounting plate (1c) to electrical junction box (1a)
using junction box screws provided (1e) in hardware
package
4. Secure mounting plate (1c) to mounting surface with
anchors (1f) and screws (1g)
5. To change fixture height, push and hold wire gripper
(2g), slide wire to desired length and then release wire
gripper (2g) to secure
6. Make proper electrical connections (black to hot “L”,
white to neutral “N”, ground to “GND”) with wire nuts
(1b) provided in hardware package
7. Attach canopy (2a) to mounting plate (1c) with canopy
screws (2b)
8. Fine tone wire length if necessary, by push and hold
wire gripper (2g) and then adjust wire to desired length
2g.
2b.
2a.
START FROM HERE
• Make sure POWER is COMPLETELY OFF at the fuse box
• Have your fixture installed by a qualified licensed electrician
• Prepare everything in a clear area
• Wear gloves at all time during this installation
• Read instructions carefully before you start assembly
• Keep this installation sheet for future reference
Technical Support: 1-855-855-8926
Page 1 of 2
Please Note:
• This Kuzco LED fixture comes with pre-wired LED module(s)
• Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary
contact with the module could cause permanent damage
• Use ELV (Electronic Low Voltage) or TRIAC type of dimmer for dimming application
• 120V input
20220322
19054 28th Avenue Surrey, BC Canada V3Z 6M3
FOR ALTERNATIVE SIDE CANOPY INSTALL
T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196
W: kuzcolighting.com
INSTALLATION SHEET
PD88118
Ceiling LED Pendant
1a.
1b.
1c.
3c.
3b.
3d.
3e.
3a.
2g.
7a.
2a.
1e.
4a.
4b.
2b.
Note: Ideal distance of wire
grippers from canopy is 16-15/16”
and 15-7/16”
START FROM HERE
• Make sure POWER is COMPLETELY OFF at the fuse box
• Have your fixture installed by a qualified licensed electrician
• Prepare everything in a clear area
• Wear gloves at all time during this installation
• Read instructions carefully before you start assembly
• Keep this installation sheet for future reference
Technical Support: 1-855-855-8926
2g.
DC
Driver
LN
-
+
Illustration 3
Low Voltage
15-7/16”
16-15/16”
Page 2 of 2
Please Note:
• This Kuzco LED fixture comes with pre-wired LED module(s)
• Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary
contact with the module could cause permanent damage
• Use ELV (Electronic Low Voltage) or TRIAC type of dimmer for dimming application
• 120V input
Illustration 1 Illustration 2
1. Disconnect output wires on driver (4a)
2. Separate wire gripper (2g) from canopy (2a) by removing
nut and tooth washer (6a). Separate plug (6b) from canopy
(2a) by removing nut, tooth washer and flat washer (6c)
(See Illustration 1)
3. Feed fixture wires through centre hole on canopy plate
(7a), canopy (2a), tooth washer and nut (5a). Attach
canopy plate (7a) to canopy (2a), followed by wire gripper
(2g) and secure with tooth washer and nut (5a) (See
Illustration 2)
4. Make proper electrical connections between LED and DC
driver, LED- Negative, LED+ Positive using wago connector
(4b) provided (See Illustration 3 and refer to diagram on
driver)
5. Make proper electrical connections (black to hot “L”,
white to neutral “N”, ground to “GND”) with wire nuts
(1b) provided in hardware package
6. Attach canopy (2a) to mounting plate (1c) with canopy
screws (2b). Position desired amount of wire by
pushing gripper (2g) on canopy
7. Pull wire through aircraft barrel (3b) and stopper (3d).
Secure aircraft barrel (3b) to mounting surface with anchor
(3c) and screw (3a). Adjust wire to desired length and
secure with set screw (3e). Insert wire gripper (2g) into
aircraft barrel (3b) to close
8. Fine tone wire length if necessary, by push and hold
wire gripper (2g) and then adjust wire to desired length
6c.
Ground Wire
7a.
6a.
2g.
2g.
6b.
2a.
5a. Ground
Wire
2a.
20220322
  • Page 1 1
  • Page 2 2

KUZCO PD88118 User manual

Type
User manual

KUZCO PD88118 is a ceiling LED pendant light fixture that combines modern design with energy-efficient LED technology. It features adjustable wire length, allowing you to customize the height of the fixture to suit your space. The fixture comes with pre-wired LED modules and is compatible with ELV (Electronic Low Voltage) or TRIAC dimmers for dimming control. Installation requires a qualified licensed electrician and should be done according to the provided instructions. Please refer to the installation sheet for detailed steps and safety precautions.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI