Page is loading ...
AREA CODE CHANGE
Please note that the area code for
Paradyne Corporation in Largo, Florida
has changed from 813 to 727.
For any Paradyne telephone number that
appears in this manual with an 813 area
code, dial 727 instead.
LINE
PHONE
DSL
97-15589
TM
1
HotWire Indoor POTS Splitter Customer Premises
Installation Instructions
Document Number 5034-A2-GN10-00
August 1997
Before You Begin
Verify that: Indoor 5034 POTS Splitter
The local loop is connected
to the POTS/DSL network.
New or existing unshielded
twisted-pair wiring (CAT3 or
better) is installed. The CAT3
wiring must meet EIA/TIA-568
specifications with 24 AWG
(.5 mm) or 26 AWG (.4 mm).
Your package contains a POTS
Splitter and a Warranty Card.
What Does the POTS Splitter Do?
The POTS Splitter and HotWire Remote Termination Unit (RTU) are components in the
DSL Access System. This system provides high-speed Internet or corporate LAN
access over traditional twisted-pair copper telephone wiring. The RTU and telephone
can function simultaneously over the same pair of copper wires at the customer
premises.
2
Copper pairs are run from the central office to your customer premises to create the
local loop. The local loop terminates on your customer premises.
97-15636
Internet
Service
Provider
RTU
Customer Premises (CP)
Ethernet
Crossover
Cable
Ethernet
Cable
or
Central
Office
(CO)
Data
Network
Local Loop
HUB
CP
POTS
Splitter
DSL Digital Subscriber Line RTU Remote Termination Unit
POTS Plain Old Telephone Service
Installing the POTS Splitter
" Procedure
The POTS splitter is made for table top placement and uses three RJ11 connections.
1. Plug the end of one cable into the POTS splitter jack labeled PHONE. Plug the
other end into jack of the telephone.
97-15619
POWER
ETHERNET
DSL
HotWire RTU
Indoor POTS
Splitter
LINE
PHONE
DSL
Line from
Local
Loop
PHONE
2. Plug the end of a second cable into the POTS splitter jack labeled DSL. Plug the
other end into the RTU jack labeled DSL.
3
3. Plug the end of a third cable into the POTS splitter jack labeled LINE. Plug the
other end into the line from the local loop.
For RTU installation information, refer to the
HotWire 5446 Remote Termination Unit
(RTU) Customer Premises Installation Instructions,
Document No. 5446-A2-GN10.
Indoor POTS Splitter Technical Specifications
Item Specification
1
Width x Depth x Height 3.63″ x 5.78″ x 1.52″ (9.22 cm x 14.68 cm x 3.86 cm)
Weight 6.7 ounces (190.0 grams)
Approvals
Safety Certifications
Refer to the equipment’s label for approvals on product.
Physical Environment
Operating temperature
Storage temperature
Relative humidity
Shock and vibration
32°F to 122°F (0°C to 50°C)
–4°F to 158°F (–20°C to 70°C)
Up to 95% (noncondensing)
Withstands normal shipping and handling
Interface Connectors Three 6-pin, non-keyed RJ11 modular plugs
1
Technical Specifications subject to change without notification.
Important Safety Instructions
1. Read and follow all warning notices and instructions marked on the product or
included in the manual.
2. This product is intended to be connected to Listed/Certified telephone wiring with a
minimum of 26 AWG (.4 mm) behind a Listed/Certified primary protector.
3. Do not attempt to install or service this product yourself, as opening or removing
covers may expose you to dangerous high-voltage points or other risks. Refer all
servicing to qualified service personnel.
4. When installed in the final configuration, the product must comply with the
applicable Safety Standards and regulatory requirements of the country in which it
is installed. If necessary, consult with the appropriate regulatory agencies and
inspection authorities to ensure compliance.
4
5. In addition, since the equipment is to be used with telecommunications circuits,
take the following precautions:
— Never install telephone wiring during a lightning storm.
— Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
— Never touch uninsulated telephone wires or terminals unless the telephone
line has been disconnected at the network interface.
— Use caution when installing or modifying telephone lines.
— Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightning.
— Do not use the telephone to report a gas leak in the vicinity of the leak.
CE Marking
When the product is marked with the CE mark on the equipment label, this
demonstrates full compliance with the following European Directives:
H Directive 73/23/EEC – Council Directive of 19 February 1973 on the harmonization
of the laws of the member states relating to electrical equipment designed for use
within certain voltage limits, as amended by Directive 93/68/EEC.
H Directive 89/336/EEC – Council Directive of 3 May 1989 on the approximation of
the laws of the member states relating to Electro-Magnetic Compatibility (EMC), as
amended by Directive 93/68/EEC.
Warranty, Sales, and Service Information
Contact your sales or service representative directly for any help needed. For additional
information concerning warranty, sales, service, repair, installation, documentation, or
training, use one of the following methods:
H Via the Internet: Visit the Paradyne World Wide Web site at:
http://www.paradyne.com
H Via Telephone: Call our automated call system to receive current information via
fax or to speak with a company representative:
— Within the U.S.A., call 1-800-870-2221
— International, call 813-530-2340.
*5034–A2–GN10–00*
/
