Firstech FTI-FDK1 1A3 Quick start guide

Brand: Firstech

Model: FTI-FDK1 1A3

Type: Quick start guide

FTI-FDK1 Type 1A3 - Vehicle Coverage & Preparation Notes

Make Model Year Install

I/O Changes

DL-FM2

Ford

Mercury

Explorer

Sport Trac

Mountaineer

2006-10

2007-10

2006-10

Type 1

CAN

Lights

RAP Trunk

Green White/BluePark / Auto

Hey! Read this stuff before you start the installation...

Firmware:

Covered vehicles use BLADE-AL(DL)-FM2 firmware, flash module and update the controller firmware before installing.

Controller Configuration:

Set feature 1-11 to option 2 (Ignition pulse - same timing as disarm pulse) for proper handling of OEM alarm.

Door Locks:

With Alarm: Door locks require three connections (1-unlock, 2-lock) and two diodes.

Without Alarm: Door locks require two wires and no diodes.

Brake:

Analog brake connection required, there are two possible connector types used, wire color is purple/white at the brake switch

connector, pin #4 of 4-pin connector, or pin #2 of the 2-pin connector, vehicle equipment varies.

Auto-Lights:

If vehicle is equipped with Auto-Light feature, refer to diagram for required connections.

OBD-II

CM-900

CM-900S/900AS

CM7X00

CM7000/7200

Cut loop for A/T

CM900AS/900S Jumper

SUPPORT - 1(888) 820-3690, EXT. 203

DEREK ZOOLANDER

Est. 2001

CENTER KIDS

WHO CAN’T READ GOOD

for

87a

STATUS

+12V

white/violet

violet/green

FT-RLY-10A

Auto-Light Detail

A B

C D E

SUPPORT - 1(888) 820-3690, EXT. 203

FTI-FDK1 Type 1A3

FTI-FDK1 Type 1A3 - Installation Notes & Wiring Diagram

33 22 114

1 2

purple/green

gray/yellow

Brake Switch

Driver’s kick panel (harness)

yellow/green

violet/green

gray/yellow

violet/gray

green/violet

blue/white

DL-FM3 TX loop, not used in this install type, do not cut.

Jumper for vehicles that are not equipped with immobilizer, do not connect unless vehicle is confirmed

not equipped. If vehicle is not equipped, connect before programming to skip immobilizer learn.

NO ALARM: Door lock connection in driver kick panel harness, color is gray/yellow

WITH ALARM: Door lock/arm connections are yellow/green and violet/green, in the driver kick panel

harness, diode isolate the factory wires (cathode toward CM) and connect to CM output

Brake status is at the brake switch assembly, wire color is violet/white in either pin #2 of a gray 2-pin

plug or pin #4 of a white 4-pin plug

Module Programming Procedure

Step 1 - Key #1 in activate IGN, if LED goes blue, you’re done

if LED goes red, wait until flashes blue then key off/on

Step 2 - If LED goes blue, you’re done, if red, insert key #2

and activate IGN, when LED is red, remove key, press

module button, and remote start vehicle, blue/done.

**See BLADE guide for more detailed instructions

PWR

BLADE

Lock

RAP

LOCK/UNLOCK

TRUNK RELEASE

OBD-II Connector

Ignition switch

blue/black

blue

white/black

white/red

DRIVER DOOR PIN

(+) PARKING LIGHTS

green/white

LED Programming Error Codes

Module LED flashing RED during programming

1x - CAN error, check wiring

2x - VIN error, check CAN wiring

3x - Wrong firmware, confirm firmware flashed

4x - VIN error, vehicle not identified, contact support

5x - Immobilizer learn error, check RX/TX wiring

6x - KLON error, check RX/TX wiring, confirm pin positions

7x - KLON error, process failed, reset module and start over

8x - Encryption error, confirm key encryption, 80 bit detected

9x - Key in cylinder, remove and proceed

lt. blue/white

BRAKE

Firstech FTI-FDK1 1A3 Quick start guide

Firstech FTI-FDK1 1A3 Quick start guide

Firstech FTI-FDK1 1A3 Quick start guide

Related papers

Other documents