ZyXEL P-873HNUP-51B Quick start guide

Brand: ZyXEL

Model: P-873HNUP-51B

Category: Networking

Type: Quick start guide

This manual is also suitable for

P873HNUP

www.zyxel.com

802.11n Wireless VDSL2 4-port

Gateway

Firmware Version 1.10

Edition 1, 5/2011

P-873HNUP-51B

DEFAULT LOGIN DETAILS

IP Address: http://192.168.1.1

User Name: admin

Password: 1234

ZyXEL Communications Corporation

Device Panels

POWER

ETHERNET 1-4

USB

WLAN/WPS

ETHERNET WAN

INTERNET

DSL 1

HPNA

POWER

ETHERNET 1-4

USB

ETHERNET WAN

HPNA

RESET

DSL 2

DSL 1

DSL 2

P-873HNUP-51B

Requirements

Make sure you have the following things before you start:

• INTERNET ACCESS: You need an Internet account with an ISP (Internet

Service Provider) and information such as your user name, password, and

so on.

• WEB BROWSER: Internet Explorer 6.0 and later versions, with JavaScript

enabled, or Mozilla Firefox 3 and later versions, or Safari 2.0 and later

versions. The browser will be used to access the Internet and/or access

the P-873HNUP-51B’s Web Configurator.

Hardware Setup

Place the P-873HNUP-51B flat on a desk or table or on the stand for a vertical

installation.

Remove the P-873HNUP-51B’s clear plastic covers before using it.

To connect the stand, line up the arrow on the stand with the arrow on the

bottom of the device as shown.

To connect your P-873HNUP-51B:

P-873HNUP-51B

1. Attach the antenna and point it up.

2. Do one of the following for your Internet connection:

a. DSL 1,2: Use a telephone cable to connect your P-873HNUP-51B’s DSL1

port to a telephone jack (or the DSL or modem jack on a splitter if you

have one).

b. If the DSLAM at your ISP supports DSL bonding function, you can

connect DSL1 and DSL2 to two seperate telephone jacks. This provides

increased throughput at longer distances. You will need to access the

Web Configurator and enable the DSL Bonding function in the

Broadband > DSL screen. See the User’s Guide for more information.

c. ETHERNET WAN: If you already have a broadband router or modem, use

an Ethernet cable to connect the ETHERNET WAN port to it for Internet

access.

3. ETHERNET: Use an Ethernet cable to connect a computer to an Ethernet

port for initial configuration and/or Internet access.

4. HPNA: Use a coaxial cable to connect to a coaxial outlet and relay Internet

traffic throughout your house through coaxial cabling.

5. USB: Connect a USB (version 2.0 or lower) memory stick or a USB hard

drive for file sharing. Use a USB extension cable if the stick is too big to fit.

6. POWER: Use the provided power adaptor to connect the POWER socket to

an appropriate power source. Make sure the power at the outlet is on. After

connecting the power adaptor, look at the lights on the front panel.

• The POWER light blinks while your P-873HNUP-51B starts up and then

stays on once it is ready.

• Each LAN light stays on if the corresponding Ethernet port is properly

connected and blinks when there is traffic.

• The ETHERNET WAN light stays on if the ETHERNET WAN port is

properly connected and blinks when there is traffic.

• The USB light turns on when your P-873HNUP-51B detects a connected

USB device.

• The HPNA light stays on if the HPNA port is properly connected and blinks

when there is traffic.

• The DSL1,2 lights are green when your P-873HNUP-51B has an ADSL

connection. They are orange when you have a VDSL connection. If you

are not using DSL bonding function, only DSL1 light will be on.

• The WLAN / WPS light flashes green when WLAN is activated and orange

while WPS is in process. It stays on green when the wireless LAN is ready

and blinks when there is traffic.

• The INTERNET light turns on when the gateway is able to access the

Internet and will blink when your P-873HNUP-51B is sending or receiving

data.

If the lights do not come on, check your connections and inspect your cables for

damage. If the lights are still off, contact technical support.

Set Up a Wireless Network

You can set up a wireless network using the following methods:

Using Wireless Protected Setup (WPS)

Press the WPS button on the P-873HNUP-51B’s front panel for more than 5

seconds to turn the WPS function on.

P-873HNUP-51B

Follow these steps to add a WPS-enabled device to the wireless network using

the WPS/WLAN button.

Set Up a Wireless Network Manually

The wireless LAN on your P-873HNUP-51B is enabled by default. To add a

wireless client to the network, use the settings found on the side panel of your

P-873HNUP-51B, which will look similar to the following example:

Configure wireless devices that you want to connect to the wireless network to

use the same wireless settings as the P-873HNUP-51B.

The default wireless settings vary for each P-873HNUP-51B. Refer to the

side panel of your device and use the provided information.

Place the devices you want to connect near one

another.

Press the WPS button on the P-873HNUP-51B.

The WPS light blinks green and orange.

Press the WPS button on a compatible device

within 2 minutes of pressing the button on the P-

873HNUP-51B.

The WPS light on the P-873HNUP-51B shines

steadily when connected.

SSID: ZyXEL00561

Security Mode: WPA-PSK

Pre-Shared Key: FB373BD356

The Web Configurator

The Web Configurator is a web browser tool that allows you to configure the P-

873HNUP-51B. The computer and the P-873HNUP-51B need to be in the same

IP address range to use this tool.

1. Open your browser and enter http://192.168.1.1 (the P-873HNUP-51B’s

default IP address) as the address.

2. Enter the default user name admin and password 1234. Click Login.

If the login screen does not open, make sure you allow web browser

pop-up windows, JavaScript and Java permissions. Your computer

should be also set to get an IP address automatically from a DHCP

server. See the appendices in your User’s Guide for more

information.

P-873HNUP-51B

3. A welcome screen appears with details about your last login. Select Show

this page next time to see the welcome screen on your next login.

Otherwise, clear it. Click Continue.

4. The Network Map page appears. This shows whether the P-873HNUP-51B

and computers/devices connected to it have Internet access.

5. Click Status to display the following screen, where you can view the P-

873HNUP-51B’s device, interface, and system information.

P-873HNUP-51B

6. Click Quick Start and configure the P-873HNUP-51B’s time zone Internet

access, and wireless settings.

See your User’s Guide for how to use the rest of the Web Configurator screens.

You will need to refer to the section on how to setup the Broadband connection

if the INTERNET LED (light) remains off.

For more information, please refer to the User’s Guide on the provided CD or at the www.zyxel.com

download library.

Was this guide helpful? Send your comments to [email protected]

Procedure to View a Product’s Certification(s)

1. Go to www.zyxel.com.

2. Select your product from the drop-down list box on the

ZyXEL home page to go to that product's page.

3. Select the certification you wish to view from this page.

ENGL

SH DEUTSCH ESPAÑOL FRANÇAIS

Green Product

Declaration

RoHS Directive 2002/95/EC

WEEE Directive 2002/96/EC

(WEEE: Waste Electrical and Electronic

Equipment)

2008/34/EC

Declaration Signature:

Name/Title:

Raymond Huang/

Quality & Customer Service Division Assistant VP

Date (yyyy/mm/dd): 2011/1/24

Green Product

Declaration

RoHS Directive 2002/95/EC

WEEE Directive 2002/96/EC

(WEEE: Waste Electrical and Electronic

Equipment)

2008/34/EC

Unterschrift des Erklärenden:

Name/Titel:

Raymond Huang/

Quality & Customer Service Division Assistant VP

Datum (JJJJ/MM/TT): 2011/1/24

Declaración de Producto Ecológico

Directiva RoHS 2002/95/EC

Directiva REEE 2002/96/EC

(REEE : Residuos de Equipos

Eléctricos y Electrónicos)

2008/34/EC

Firma de declaración:

Nombre/Título:

Raymond Huang/

Quality & Customer Service Division Assistant VP

Fecha (aaaa/mm/dd): 2011/1/24

Déclaration de Produit

Green

Directive RoHS 2002/95/EC

Directive DEEE 2002/96/EC

(DEEE : Déchets des Equipements

Electriques et Electroniques)

2008/34/EC

Signature de la déclaration :

Nom/Titre :

Raymond Huang/

Quality & Customer Service Division Assistant VP

Date (aaaa/mm/jj) : 2011/1/24

ITALIANO

NEDERLANDS

SVENSKA

Dichiarazione Green

Product

Direttiva RoHS 2002/95/CE

Direttiva RAEE 2002/96/CE

(RAEE: Rifiuti di Apparecchiature

Elettriche ed Elettroniche)

2008/34/EC

Firma dichiarazione:

Nome/titolo:

Raymond Huang/

Quality & Customer Service Division Assistant VP

Data (aaaa/mm/gg): 2011/1/24

Productmilieuverklaring

RoHS-richtlijn 2002/95/EC

AEEA-richtlijn 2002/96/EC

(AEEA: Afgedankte Elektrische en

Elektronische Apparaten)

2008/34/EC

Verklaringshandtekening:

Naam/titel:

Raymond Huang/

Quality & Customer Service Division Assistant VP

Datum(jjjj/mm/dd): 2011/1/24

Miljödeklaration

RoHS Direktiv 2002/95/EC

WEEE Direktiv 2002/96/EC

(WEEE: hantering av elektriskt och

elektroniskt avfall)

2008/34/EC

Deklaration undertecknad av:

Namn/Titel:

Raymond Huang/

Quality & Customer Service Division Assistant VP

Datum (åååå/mm/dd): 2011/1/24

ZyXEL P-873HNUP-51B Quick start guide

Brand: ZyXEL

Model: P-873HNUP-51B

Category: Networking

Type: Quick start guide

This manual is also suitable for

P873HNUP

Download PDF

report

ZyXEL P-873HNUP-51B Quick start guide

This manual is also suitable for

ZyXEL P-873HNUP-51B Quick start guide

Related papers

Other documents