Hitachi 36UX58B Operating instructions

3olid State Color TV

_)PERATING GUID

IMPORTANT SAFEGUARDS

FIRST TIME USE

THE GENIUS

REMOTE CONTROL

2-4

5-20

21-37

ULTRATEC BIT-MAP

ON-SCREEN DISPLAY

38-61

K USEFUL INFORMATION INDEX 62-67

IMPORTANT

Followall warningsand instructionsmarked on this color television.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUAUFiED SERVICE PERSONNEL

The lightning flash with arrowhead symbol, within an equilateral tri-

angle, is intended to alert the user to the presence of uninsulated

=dangerous voltage" within the product's enclosure g_atmay be of a

sufficient magnitude to constitute a dsk of electric shock to persons.

The exclamation point within an equilateral triangle, is intended to

alert the user to the presence of Important operating and maJnte-

nence (servicing) instructions in the literature accompanying the

appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE

THIS COLOR TELEVISION TO RAIN OR MOISTURE.

I NOTE:

• There are no user serviceable parts inside the television.

• Model and serial numbers are indicated on back side of the television.

I

CAUTION:

• Adjust only those controls that are covered in the instructions, as improper

changes or modifications not expressly approved by Hitachi could void the user's

authority to operate the TV.

POWER SOURCE

This HITACHI color television is designed to operate on 120 volts 60Hz, AC current.

Insert power cord into a 120 volt 60Hz outlet.

TO PREVENT ELECTRIC SHOCK, DO NOT USE THE TELEVISION'S (POLARIZED) PLUG

WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES

AND GROUND TERMINAL CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NEVER CONNECT THE TELEVISION TO 50HZ, DIRECT CURRENT, OR ANYTHING OTHER

THAN THE SPECIFIED VOLTAGE.

I NOTE:

This television receiverwilldisplay television closed captioning, (r_ or I_), in accordance with para- I

graph 15.119 of the FCC rules.

I

CAUTION:

I

Never remove the back cover of the television as this can expose you to very high voltages and other hazards. I

Ifthe television does notoperate properly, unplugthe television and call your authorized dealer or service shop.

I

SAFETY TIPS

IMPORTANT SAFEGUARDS

CAUTION: • Read all of these instructions.

• Save these instructions for later use.

• Follow all warnings and instructions marked

on the television.

SAFETY POINTS YOU SHOULD KNOW ABOUT

YOUR HITACHI COLOR TELEVISION

Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions.

Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustratessafety tips which

will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI television.

Please fill out your warranty card and mail it to HITACHI. This will enable HITACHI to notify you promptly in the improbable event that a safety

problem should be discovered in your product model.

FOR YOUR PERSONAL SAFETY

1. This television set isequipped with a

polarized allemating-oummt line ptug

(a plug having one blade wider than

the other.) This plug will fit into the

power outlet only one way. This is a

safely feature. If you are unable to

insert the plug fully into the outlet, try

reversing the i_u9. If the plug should

still fall to fit. contact your electrician

1o replace your obsolete outlet. Do

not defeat _ safety purpose OI the

peismed i_,ug.

2. When the power cord or plug is

damaged or frayed, unplug the

television from the wall outlet and

refer servicing to qualified service

personnel.

3. Do not overload wall outlets and

exlensidn cords as this can result in

fire or electric shock.

4. Do not allow anything to rest on or

roll over the power cord, and do not

place the television where the

power cord is subject to traffic or

abuse. This may result in a shock

or fire hazard.

Oono--o--h OOn --ro

television yourself as opening or wall outlet before cleaning. Use a

removing covers may expose you damp cloth for cleaning. Do not

to dangerous voltage or other use liquid or aerosol cleaners.

hazards. Refer all servicing to

qualified service personnel.

5.

Never push objects of any kind into

the televisiun's cabinet slots as they

may touch dangerous voltage points

or short out parts that could result in

a fire or eleotdc shock. Never spill

liquid of any kind on the television.

It the television has been dropped or

the cabinet has been damaged,

unplug the television from the wall

outlet and refer sewicing to qualified

service personnel.

If liquid has been spilled into the

television set. unplug it from the

wall outlet and refer service to

qualified service personnel,

DO not subject your television to

impact of any kind. Be careful not to

damage the picture tube sudace.

11-1. Do not place the television on an

unstable cart, stand, or table. The

television may fall, causing

serious injury to • child or an

adult, and serious damage to the

appliance. Ueaonlywithacartor

stand recommended by the

manufacturer, or sold wi_ the

television. Wal or shelf mounting

should follow the menutacturer's

instructions, and should use a

mounting kit approved by the

manufacturer.

11-2. An applience and cart combination

should be moved with care.

Quick slops, excessive force, and

uneven sudaces may cause the

appliance end cart combination

to overturn.

PROTECTION AND LOCATION OF YOUR TELEVISION

12. Do not use the lelevision near

water, for example, near a bathtub,

washbowl, kitchen sink. or laundry

tub, in a wet basement, or near a

swimming pool. etc.

• Never expose the television to

rain or water. If the set has been

exposed to rain or water, unplug

television from wall outlet and

refer to qualified service person-

nel.

13. Choose a place where light

(artificial or sunlight) does not

shine directly on the screen.

14. Avoid dusty places. Accumulated

dust inside the chassis may cause

failure of the television when high

humidity persists.

15. The television has slots or openings

in the cabinet for ventilation

purposes which provide reliable

operation of the receiver and

protect the television from

overheating. These openings must

not be blocked or covered.

• Never cover the slots or openings

with cloth or other material.

Never block the bottom ventilation I_

slots of the television by placing it on

a bed, sofa, rug, etc.

Nevor pl&ce the television near or _'f,'_*"*,'_

over a radiator or heat register.

• Never p/ace the television in a built-in

enclosure oniass proper ventilation

is provided.

3

SAFETY TIPS'

PROTECTION AND LOCATION OF YOUR TELEVISION

16-1. Ifan outside antenna isconnected

to the television, be sure the

antenna system is grounded so as

to provide some protection against

voltage surges and betH-up static

charges. Section 810 of the

National Electrical Code, NFPA

No. 70-1975, provides information

with respect to proper grounding

of the mast and supporting

structure, grounding of the lea@in

wire to an antenna discharge unit,

size of grounding conductors,

location of antenna discharge unit

connection to grounding

electrode, and requirements for

the grounding electrode.

16-2. Nole to CATV system installer:

(Only for television with CATV

reception). This reminder is

provided to call the CATV system

insteller's attention to Article

820-40 of the NEC that provides

guidelines for proper grounding

and, in particular, specifies that

the cable ground shall be

connected to the grounding

system of the building, as close

to the point of cable entry as

practical.

OPERATION OF YOUR TELEVISION

19. This television should be operat-

ed only from the type of power

source indicated on the marking o_ ,_/_

label. If you are not sure of the

type of power supply at your

home. consult your dealer or local

power company. For televisions

designed to operate from battery

power, refer to the operating

instructions.

T

NEeMlX_'W. B.ECTI_.K_

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL

CODE INSTRUCTIONS.

17. An outside antenna system should

not be located in the vicinity of

overhead power lines or other

electrical lights or power circuits.

or where it can fall into such power T _

lines or circuits. Wtlen installing an II ._x /'DO o'_1_

outside antenna system, extreme _ _,_o, I D J I

care should be taken to keep from _ -L--.._J-t.

touching such power lines or

circuits as contact with them might

be fatal.

18. For added protection for the

television during a lightning storm.

or when it is unused for long

periods of time, unplug it from the

wall outlet and disconnect antenna.

This will prevent damage due to

lightning and power-line surges.

20.

If the television does not operate

normally by folowing the obeceting

instrucifons, unplug the telmCslen

from the wall outlet end refer *---"-_ €''%*"_

servicing to qualified service

personnel. Adjust only those

controls that are covered in the

insuuctk_ns as improper adjustment

of other controls may result in

damage and wilt often require

extensive work by • qualified

sennus technician to restore the

televislen to normal operetiork

21. If your television is to remain p_ __.

unused for a period of time. (such

as when going on a holiday), turn

the television OFF and unplug it

from the wall outlet.

IF THE TELEVISION DOES NOT OPERATE PROPERLY

22. If you are unable to restore

normal operation by following

the detailed procedure in your

operating instructions, do not

attempt any further adjustments.

Unplug the television and call

your dealer or service technician.

23. Whenever the television is

damaged or fails, or if there is a

distinct change in performance

that indicates a need for service.

unplug the television and hove it

checked by a qualified service

technician.

24. It is normal for some televisions to

make occasional snapping or

popping sounds, particularly v/nan

being turned on or off. if the

snapping or popping is continuous

or frequent, unplug the set and

consult your dealer or service

technician.

FOR SERVICING AND MODIFICATION

25. Do not use attachments not

recommended by the television

manu/ecturer as they may cause

hazards.

j,_ o 26. If replacement beds ere required, 27. Upon completion of any service or ._. ,_,

be sure the service technician has repairs Io the television, ask the

used replacement parts specified by service technician to perform

the manufacturer that have the routine safety checks to determine

same charectenstlos es the original that the television is in sate

bert. Unauthorized substitutions operatingsonditlon.

may result in fire. electric shock, or

olhe¢ hazards.

PICTURE CAUTIONS

Picture Burn Prevention

• Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and

other fixed (non-moving) patterns can cause permanent damage to television receivers. Such =PATTERN BURNS"

constitutemisuse and are NOT COVERED byyour HITACHI FactoryWarranty.

• When using Picture-in-Picturefunction,the sub-pictureshouldnot be left permanently in one cornerof the screen or a

"PA'I-I'ERN BURN" may develop over a long period of time.

Public Viewing of Copyrighted Material

Public viewing of programs broadcast by TV stationsand cable companies, as well as programsfrom other sources, may

require priorauthorizationfrom the broadcaster or owner of the video program material.

4

ACCESSORIES

Check that you have the following accessories before disposingofthe packing material.

1. Remote Control Unit (See Part No. below)

2. Two "AA" size, 1.5V batteries (For Remote Control Unit).

For information regarding how to obtain these accessories, please call TOLL FREE 1-800-448-2244 for the nearest HITACHI

Authorized parts Distributorin the United States. For Alaska and Hawaii, please contact your nearest HITACHI regional office.

PARTS NAME

36UX58B

CLU-612MP

REMOTE CONTROL

PART NO.

HL00712

36FX48B

32FX48B

CLU-431UI

REMOTE CONTROL

32V TELEVISION STAND

SP316B

(Notincluded,orderseparately)

32V TELEVISION STAND

SP317B

(Notincluded,orderseparately)

36V TELEVISION STAND

SP351B

(Notincluded,orderseparately)

.HL00721

H530022

H530023

(upgrade)

H530024

.=.:,

(3_(3DGD

(3D(3_(3D

CD(3D(3D

CLU-612MP

ILLUSTRATION

I

0000

_ €_TP,m

CD CDCD

_CDCD

CLU-431U!

CUSTOM HITACHI

TELEVISION STAND

Excellent for VCR and video-

tape storage. Special fea-

tures includes curved smoke

glass doors and an

adjustable shelf.

Available in Black.

J_Ik CAUTION:

Television stand models SP316B and SP317B are designed for use only with a 32 inch or smaller television

set. Television stand model SP351B is designed for use with a 36 inch or smaller television set. Use of a

smaller stand, a non Hitachi recommended stand or a generic stand may result in instability,causing possible

injury.

REMOTE CONTROL BATTERY INSTALLATION

AND REPLACEMENT

1. Open the battery cover of the remote controlby

pushing the notched part of the cover with your

fingers.

2. Insert two new "AA" size batteries for the remote

control. When replacing old batteries, push

them towards the springs and lift them out.

3. Match the batteries to the (+) and (-) marks in

the battery compartment.

4. Replace the cover.

BOTTOM VIEW

Push in and lift up on tab to

remove back cover.

CAUTION:

1.

2.

3.

4.

If your television set is to remain unused for a long period of time, for instance when you go on vacation, unplug the television from the wall

outlet.

Do not subject the remote control to shocks such as dropping it on the floor, etc. Precision parts may be damaged.

Do not allow the remote control to become wet and avoid placing it in areas of high humidity. Do not leave it on or near a heater. Excess heat

or moisture may cause the unit to cease operation.

If the batteries become exhausted, remote controloperation may become erratic or stop altogether. Replace the old batteries with new "AA"

type.

NOTES:

1. The CHANNEL NO., VOLUME and OFF TIMER indicator are not displayed simultaneously.

2. To operate your TV, point the remote control at the remote sensor of the TV.

HOW TO SET UP YOUR NEW HITACHI COLOR TV

ANTENNA

Unless your TV is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is

recommended for best performance. However, if you are located in an exceptionally good signal area that isfree from interferenceand

multipleimage ghosts, an indoor antenna may be sufficient.

LOCATION

Select an area where sunlight or bright indoor illuminationwill not fall directly on the picture screen. Also, be sure that the location

selected allows a free flow of air to and from the perforated back cover of the set.

To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can

become excessively hot, for example, in direct sunlightor near a heating appliance, etc.

VIEWING

The major benefit of the HITACHI Color Television is its large viewing screen. To see this large screen at its best, test variouslocations

in the room to findthe optimum spot for viewing. The drawings give several suggestions.

The best picture is seen by sitting directlyin front of the "IV and about 6 to 9 feet from the screen. During daylight hours, reflections from

outside light may appear on the screen. If so, drapes or screens can be used to reduce the reflection or the "IV can be located in a

different section of the room.

If the "FV'saudio output will be connected to a Hi-Fi system's external speakers, the best audio performance will be obtained byplacing

the speakers equidistant from each side of the receiver cabinet and as close as possible to the height of the picturescreen center. For

best stereo separation, place the external speakers at least four feet from the side of the "IV, place the surroundspeakers to the side

or behind the viewing area. Differences in room sizes and acoustical environments will require some experimentation with speaker

placement for best performance.

4' MINIMUM

I ,_CAUTION:

Magnetic fields, such as those of external speakers, may cause the picture to distort if they are placed too

close to the television. Move the magnetic field source away from the television until there is no picture

distortion.

I

HOOK-UP CABLES AND CONNECTORS

Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors.

For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell

audio/videoproducts. Below are illustrations and names ofcommon connectors. Before purchasing any cables, be sure of the output

and inputconnectortypes required by the various components and the length of each cable.

300-Ohm Twin Lead Connector

This outdoor antenna cable must be connected to an antenna

adapter (300-Ohm to 75-Ohm).

"F" Type 75-Ohm Coaxial Antenna Connector

For connectingRF signals (antenna or cableTV) to the antenna

jack on the television.

Phono Connector

Used on all standard video and audio cables which connect to

inputsand outputslocated onthe television's rear jack panel and

front control panel.

S-Video (Super Video) Connector

This connector is used on camcorders, VCRs, and laserdisc

players with an S-Video feature in place of the standard video

cable to produce a high quality picture.

Antenna Connections

These sets are equipped with one VHF/UHF antenna terminal. The VHF/UHF terminal can be used for normal TV, cable TV (CATV), a

TV game, etc.

1.

VHF (75-Ohm) antenna/CAW (Cable TV)

When using a 75-Ohm coaxial cable system, connect

the outdoor antenna or CATV coaxial cable to the ANT

A (75-Ohm) terminal. If you have a second antenna or

cableTV system, connect the coaxial cable to the ANT

B terminal.

Tooutdoor or CATVcable

L VHFAJHF ,,

75Ohm I I Q,hlL _L t (disconnect)

C°axia_...jb= LI,_ _@, (_L.J ._F Adapt°r

2. VHF (300-Ohm) antennaiUHF antenna

When using a 300-Ohm twin lead from an outdoor

antenna disconnect the (VHF or UHF) indoor antenna

leads from screws of the (VHF or UHF) adaptor and

connect outdoor (VHF or UHF) antenna leads to these

screws of a (VHF of UHF) adaptor.

To outdoor VHF

t or UHF Antenna

_llL _ (connect)

_.,_._Adaptor

3. When both VHF and UHF antennas are connected

Attachan optionalANTENNA MIXER to the TV antenna

terminal and connectthe cables to the ANTENNA

MIXER.

VHF/UHF

(RearofTV set)

ToUHF Antenna II_

To

outdoor

.,,._.__ 4"_VHFAntenna

ANTENNA

MIXER

Notes:

1. If an outdoor antenna/CATV is used, disconnect the

indoor antenna. Ghosting and poor reception may

result if both the indoor and outdoor antennas/CATV

are connected at the same time.

2. Consultyour dealer or service store for the ANTENNA

MIXER and (VHF or UHF) adaptor.

3. The special converter (decoder) willbe supplied by the

cable company.

FRONT PANEL CONTROLS FOR 32FX48B

• FRONT VIEW

L J _ I Iooeeocn| • I

I

HOW TO OPEN THE DOOR

I m

1. Push on "_"

2. Pullthe door toward the front to open it.

O

Dual Tuner PIP I

(_) RemoteControl

InfraredSensor

FRONT INPUT JACKS

I I INPUT3 I J

0 0 0

(_) Video:3 Input-_

0 @ ®

Volume

Button Butbm Burns

VOL- VOI.* C_ Oe.

0000000

MENU--I I I I I I

.4 • • •

Exrr.-----J I I I I

CURSOR

See pages 25 and 26 for

MENU, CURSOR, and EXIT

buttonoperations.

A detailed explanation of the circled numbers ison page 11.

FRONT PANEL CONTROLS FOR 36UX58B AND 36FX48B

FRONT VIEW

For 36UX58B Only

/.1111111/IBII

I

@ @ ® ®

InmUF_xit Volume Channel

Button Buttons Butto_

--1 _-I r-h I

Vvol.& • ot •

O00QO00

MENUEX=r ,4 I_ • •

r

I Dual Tuner PIP (O)',-- .,_.,,,_

MENUJ I I I I I

CURSOR

Remote Control

Infrared Sensor

See pages 25 and 26 for

MENU, CURSOR, and EXIT

button operations.

FRONTINPUTJACKS

0000 0 O0

A detailed explanation of the circled numbers is on page 11.

i

I NOTE: (e)°SOl, INI} RErRIEVAL _ is for MODEL 36UX58B only.

10

FRONT PANEL JACKS AND CONNECTIONS

I I

INPUT/EXIT button

Press this buttonto selectthe currentantenna source of VIDEO: 1,2, 3. Your selectionis shown in the top rightcomer ofthe screen.

This button also serves as the EXIT buttonwhen in MENU mode.

VOLUME Level

Press these buttons for your desired sound level. The volume level will be displayed on the TV screen.

CHANNEL Selector

Press these buttons untilthe desired channel appears in the top right corner of the TV screen.

POWER Button

Press this buttonto tum the TV on or off.

NOTE:

Your HITACHI TV will appear to be turned off ifthere is no video input when VIDEO: 1, 2, or 3 isselected. If you have

no inputto VIDEO: 1, 2, or 3, pressthe INPUT button until the normal broadcast picture appears. (See page 25.)

If the picture does not appear, the power is OFF.

®

REMOTE CONTROL INFRARED Sensor

Point your remote control at this area when selecting channels, adjusting volume, etc.

FRONT INPUT JACKS

Use these audio/video jacks for a quick hook-up from a camcorder or VCR to instantlyview your favorite show or new recording.

Press the INPUT button until VIDEO:3 appears in the top rightcorner of the TV screen. If you have mono sound, insert the audio

cable intothe left channel jack.

I NOTE: Front panel control CURSOR operation will not appear the FAMILY FAVORITES channel function. I

11

FRONT PANEL JACKS AND CONNECTIONS

The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following

examples:

Video Camera

0

_ OUTPUT

Insert audio cable

into left channel

for mono sound

/

INPUT

°°°

/

Video Camera

OUTPUT

INPUT

/ /

NPUT f

OO

I°°°° Y

S-VHS V L R

OUTPUT |

(BackolVCR)

I NOTE:

t

Completely insert connection cord plugs when connectingto front panel jacks. If you do not,the picture that is played

back may be abnormal.

12

REAR PANEL JACKS

Ili.o]11

4 ÷

VHF/UHF

ANTENNA TERMINALS

(9

lJ

36FX48B and 32FX48B

/INT IJ TO ANlrA

o _ _Q

L._

Q

INPUT TERMINALS

I

I I

(

• I WE,AK STRONG

" _ 8-VIDEO

AUDIO TO HIFI _,_ INPUT

OUTPUT TERMINALS

36FX48B only_,

I

(_) GEO_GNETISM J

CORRECTION z

I

r

36UX58B

(_) MONITOR OUT '

INPUT TERMINALS

I, I

1_;16°16°1

i t=oz_/.ll_zl l

IOflOilOil<

/o_ .1o4 '1,

I

INPUT

) AUDIO TO HIFI OUTPUT TERMINALS

13

REAR PANEL JACKS

(_ Antenna Inputs

The remote control allows you to switch between two separate 75-Ohm RF antenna inputs, ANT A and ANT B. ANT A inputcan

be displayed as a main picture or sub-picture. ANT B can only be displayed as a main picture. (ANT B cannot be displayed as a

sub-picture.) The antenna output labeled =TOCONVERTER" allows the ANT A connection to pass directly to a different source

such as a cable box.

O Audio/Video Inputs 1, 2

The INPUT button will step through each video source and antenna source input each time it is pressed. Use the audio and video

inputs to connect extemal devices, such as VCRs, camcorders, laserdisc players, etc. (If you have mono sound, insertthe audio

cable intothe left channel jack.)

(_) Monitor Out (36UX58B ONLY)

These jacks provide fixed audio and video signals which are used for recording.

(_) Audio to HI-FI

These jacks provide variable audio output to a separate stereo amplifier. With this connection, the audio to the stereo can be

controlledby the television's main volume. Use these jacks for the SURROUND Leftand Right channels. (See page 20)

(_ S-Video

Inputs 1 provide S-Video (Super Video) jacks forconnecting equipment with S-Video outputcapability.

(_ Goemagnetism Correction (36FX48B Only)

This TV has a super-large color picture tube. The effects of geomagnetism may cause an uneven (partially) colored picture

depending on the directionthe TV isfacing. Adjust the TV as follows for best performance:

1. Turn the Power uO_.

2. Decide on the installation position and directionof the TV. Check the directionthe TV isfacing at this time.

3. Set the DIRECTION and STRENGTH switches (on back of the TV) according to the directionof the screen as shown in the

table.

DIRECTION

FACING

SCREEN DIRECTION

North

Northeast

East

Southeast

South

Southwest

West

Northwest

SWITCH

DIRECTION

N

*E/W

E/W

**F.JVV

s

**E/W

E/W

*F_AN

STRENGTH

STRONG

WEAK

STRONG

WEAK

*ifthe Screenisfacinga Northerlydirection,setto"N'.

**IftheScreenisfacinga Southerlydirection,set to"S'.

4. After setting the switches, place the TV in the decided location.

5. After relocating the TV, tum the power =ON"and checkto make sure that the screen color (especially at the corners) iseven.

Depending on the installation location (especially where it is susceptible to goemagnetism, for example, in a reinforced concrete

building), in this case, set the DIRECTION and STRENGTH switches to set the optimum picture.

6. In certain areas, if the screen points North or South, color unevenness may be reduced when the STRENGTH switch is set to

STRONG rather than WEAK.

I NOTE: If you move your TV, the DIRECTION and STRENGTH switches may need to be reset. I

I

TIPS ON REAR PANEL CONNECTIONS

The S-Video connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these con-

nections in place of the standard video connection if your device has this feature.

If your device has only one audio output (mono sound), connect it to the left audio jack on the television.

Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables.

A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output (INPUT: 1

in the example on page 15 or 16.) Refer to your VCR operating guide for more information on line input-output connections.

14

REAR PANEL CONNECTIONS 136FX48B AND 32FX48B I

IJ

W

o_ Iol

StereoSystemAmpli6er

Ouside antenna or

cable "IV coaxial cable

l [,_-2-Way signal

J " splitter

_I

CableTVBox

IF OO

1_1o _v_ °L

!

Typicalfull feature setup. Follow connections that pertain to your personal entertainment system.

15

I

REAR PANEL CONNECTIONS 136UX58B )

I

Ouside antenna or

cable TV coaxial cable

l _-_ 2-Way signal

I - splitter

onpage14 '_J I

-'{_1

CableTVBox

I =

VCR#1 : ;

LaSermc0d_er,Player.VCR,

VCR#2 I_ _ '-"_

I

IOo ooLOol

o_ IOl

StereoSystemAmplifier

Typicalfull feature setup. Follow connectionsthat pertainto your personal entertainment system.

16

EXTERNAL CONNECTIONS

CONNECTING EXTERNAL AUDIO AMPLIFIER

Tocontrol the audio level of an external audio amplifierwith the remote control, connect the system as shown below.

EXTERNAL

SPEAKERS

(REAROFTVSET)

AUDIOTO HI-FITERMINAL

TO AUDIO INPUT TERMINAL

OF

©

AUDIO AMPLIFIER

-'--_L

I

AUDIO

TO HI-FI

EXTERNAL

SPEAKERS

NOTE:

To prevent damage to the speaker and distorted sound, set the volume control of the audio amplifier lower and adjust

the sound using the remote controlof the TV set.

17

CONNECTING EXTERNAL VIDEO SOURCES

The exact arrangement you use toconnect the VCR, camcorder, laserdiscplayer to yourTV set isdependent on the modeland features

of each component. Check the owner's manual of each component for the location of video and audio inputs and outputs.

The followingconnectiondiagrams are offered as suggestions. However, you may need to modifythem toaccommodate your particular

assortment of components and features. For best performance, video and audio cables should be made from coaxial shielded wire.

Before Operating External Video Source

The inputmode ischanged every time the INPUT buttonispressed as shown below. Connect an extemal sourceto the INPUT terminal,

then press the INPUT button as necessary to view the input source. (See page 25.)

INPUT MODE SELECTION ORDER

(Antenna)

(Input)

VIDEO

NOTE:

I

When the TV is set to VIDEO and a video signal is not received from the VIDEO INPUT JACK on the jack panel ofthe J

TV (i.e., VCR/laserdisc player, etc. is not connected or the video device is OFF), the screen will be gray-blue.

I

CONNECTING A MONAURAL AUDIO VCR OR LASERDISC PLAYER

1. Connect the cable from the VIDEO OUT of the VCR or the laserdiscplayer to the INPUT (VIDEO) jack on the TV set below.

2. Connect the cable from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO) jack.

3. Pressthe INPUT buttonto view the program from the VCR or the laserdiscplayer. The VIDEO mode disappears automatically after

approximately eight seconds.

4. Press the INPUT button to return to the previous channel.

TV INPUT

TERMINAL

INPU'I

VIDEO

[lr_',\

\\_.JJl

IMONO_

AUDIO

=

VCR

VIDEOOUT AUDIOOUT

I® ®1

18

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING A STEREO VCR OR STEREO LASERDISC PLAYER

1. Connect the cable from the VIDEO OUT of the VCR of the laserdisc player tothe INPUT (VIDEO) jack on the TV set below.

2. Connect the cable from the AUDIO OUT R of the VCR or the laserdiscplayer to the INPUT(AUDIO/R) jack.

3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player tothe INPUT(AUDIO/L) jack.

4. Press the INPUT button to view the program from the VCR or laserdisc player. The mode VIDEO disappears automatically after

approximately eight seconds.

5. Press the INPUT button to return to the previous channel.

INPUT11

VIDEO

O

(MONOI/oL

AUDIO

TV INPUT TERMINAL

000

S-VHS V L R

OUTPUT

BACKOF VCR

HITACHI MODEL

orsimilarmodel

NOTE:

Completely insertthe connection cord plugswhen connectingto rear panel jacks. The picturethat is played back willbe

abnormal if the connection is loose.

If you have an S-VHS VCR, use the S-INPUT cable in place of the standard video cable.

A single VCR can be used for VCR #1 and VCR #2, but notethat a VCR cannot record its own video or lineoutput.

(INPUT: 1 in example on pages 15 or 16.) Refer to your VCR operating guide for more information on line input-output

connections.

19

AUDIO SYSTEM SETUP

Match the numbers below to the diagrams for speaker placement and refer to the table for the different surroundsound requirements.

(See page 58 and 59 for SURROUND and SRS functions.)

0 The television's internal speakers.

(_ These speakers are connected to a separate audio amplifier. Use the =Audio to HI-FI" output on the television.

®

0

L '4"_

II

L J

3

l

®

0

L'-' .... " ' '__!'

I

LR

OUT IN

STEREOSYSTEM O

AMPUFIER

FOR 36FX48B AND 32FX48B

3 WAY SURROUND

FEATURE

OFF

MUSIC

MOVIE

SIMULATE

REQUIRED

CONNECTION

O

O®

OPTIONAL

CONNECTION

0

.°

EFFECT

Receive mono and stereo sound.

At stereo input, sound of music will be louder.

Surround channel added to left and right audio

amplifier speakers.

Movie theater reproduction, surround channel

added to left and right audio amplifier speakers.

At mono input, sound will be louder.

FOR 36UX58B

sns(e

FEATURE

ON

OFF

REQUIRED

CONNECTION

O

OPTIONAL

CONNECTION

@

EFFECT

Exciting and realistic 3D sound experience

from just two speakers. Sound Retrieval System.

Receive mono and stereo sound.

20

Page is loading ...

Hitachi 36UX58B, 32FX48B, 36FX48B Operating instructions

Related papers

Other documents