Trinitron °CoIor TV
Operating Instructions
KV-27S15
KV-27V15
KV-29RS15
KV-32S15
KV-32S16
KV-32V15
KV-32V16
KV-34V15C
_c%1995bv Sony Corporation
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
RISK OF I_LECTRIG SHOCK
DO NOT OpEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR SACK)
NO USER.SERVICEABLE PASTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
This symbol is intended to alert the user to the
presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock'to per'sons.
This symbol is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
CAUTION
To prevent electric shock, do not use this polarized AC plug
with an extension cord, receptacle or other outlet unless the
blades can be fully inserted to prevent blade exposure.
Precautions
Safety
• Operate the TV only on 120 V AC (except KV_34V15C).
• Operate the TV only on 220-240 V AC (KV-34V15C).
• One blade of the plug is wider than the other for safety
purposes and will fit into the power outlet only one way.
If you are unable to insert the plug fully into the outlet,
contact VOklr dealer.
• Should any liquid or solid object fall into the cabinet,
tmplug the TV and have it checked by qualified
personnel before operating it any further.
2 I
• Unplug the TV from the wall outlet if you are not going
to use it for several days or more. To disconnect the cord,
pull it out by the plug• Never pull the cord itself.
For details concerning safety precautions, see the supplied
leaflet "IMPORTANT SAFEGUARDS"
Installing
• TO prevent internal heat build-up, do riot block the
ventilation openings.
• Do not install the TV in a hl_t or hulnid place, ol in a
place subject to excessive dust or mechanical vibration.
CAUTION
When using TV games, computers, ancl similar products with
your TV, keep the brightness and contrast functions at low
settings. If a fixed (non-moving) pattern is left on the scrt_n
for long periods of time at a high brightness or contrast
setting, the image can be permanently imprinted onto the
screen. These types of imprints are not covered by your
warranty because they are the result of misuse.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment
Note on Caption Vision (except for KV-29RS15)
This television receiver provides display of television closed
captioning in accordance with § 15.119 of the FCC rules
Note to CATV system installer
This reminder is provided to call the CATV system installer's
attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
Use of this television receiver for other than private \,iewing
of programs broadcast on UHF or VHF or transmitted by
cable companies for the use of the general public may require
authorization from the broadcaster/cable company and/or
program owner.
Owner's Record
The model and serial numbe?s are Incated at the rear of the
TV. Record these numbers in the spaces provided below.
Refer to them whenever you call upon your Sony dealer
regarding this product.
Model No.
Serial No.
4 Welcome!
4 Checking your model number
Getting Started
$ Step 1: Hookup
9 Step 2: Setting up the remote commander
10 Step 3: Setting up the TV automatically
(AUTO SET UP)
13 Changing the menu language
Operations
14 Watching the TV
15 Watching two programs at a time---PiP
16 Adjusting the picture (VrDEO)
17 Adjusting screen bright-hess automatically
(LU_SVONDER)
18 Adjusting the sound (AUDIO)
19 Listening to surround sound (SURROUND)
19 Selecting Stereo or bilingual programs (MTS)
20 Setting the speaker switch (SPEAKER)
20 Setting audio out (AUDIOOUT)
21 Customizing the channel number buttons (crt
CAPTION/GUIDE)
22 Setting video labels (VIDEOLABEL)
23 Displaying Caption Vision (CAFT1ONVlSlON)
24 Operating video equipment
25 Operating a cable box
Additional Information
27 Troubleshooting
29 Specifications
30 Index
The captions in parentheses indicate menu names.
I 3
Thank you for purchasing the Sony Trinitron ®Color
TV. Here are some of the features you will enjoy with
your TV:
• Oa-screen menus that let you set the picture quality,
sound, and other settings.
• Surround system that simulates the sound quality of a
concert hall or movie theater.
• Picture-in-Picture that allows you to watch another TV
channel, video or cable image as a window picture.
• Cable box control (Cable Mouse) that allows your TV
tocontrol channel selection on most brands of cable
boxes (KV-27VI5/32VI5/32V16 only).
• Lumisponder that automatically adjusts the brightness
of the screen (KV-27V15i32V15/32V16i34V15C only).
The instructions in this manual are for eight models
listed below. Before you start reading, check your
model number by looking at the rear of your TV. The
KV-27S15 is the model used for illustration purposes.
Any differences in operation are clearly indicated in the
text, for example, "KV-27S15 only."
Instructions in this manual are based on the remote
commander. You can also use the controls on the TV if
they have the same name as those on the remote
commander.
Feature packages
._ .~
-I:(:ll((il
number
KV-27SI5
_v-_v_sI'1"1 I'l'l'r'l
KV-29Rs_sI 1"1 ! [ I I I
KV'32V15 I q t q q q q " I
KV-34WSCI,I I'1 I'i'l I
/
* Refer to the supplied Cable Mouse manual for
additional information specific to its use.
4 I
Getting Started
Although you can use either an indoor antenna or
outdoor antenna with your TV, we recommend you to
connect an outdoor antenna or a cable TV system to get
better picture quality.
How to connect different types of
cables
The illustrations below show the examples of
connecting cable to the TV directly.
A (Rearof TV)
• VHF only 75-ohm coaxial cable VHF/UHF
or
• VHFIUHF
or
• Cable
B
(Rear of TV)
• VHFonly 300-ohm twin lead cable VHF/UHF
or
• UHFonly
or
• VHF/UHF
Arltenfla connector
C
• VHF
and
• UHF
7S-ohm coaxial cable
.m. (Rear of I"V)
EAC-66UPI mixer
_- _ (not suppliedl
300-ohm twin lead cable
Notes
• Most VHF/UHF combination antermas have a signal splitter.
Remove the splitter before attaching the appropriate connector.
• If you use the U/V mixer, snow and noise may appear in the
picture when viewing cable TV channels over 37.
Connecting an antenna/cable TV
system without a VCR
If your cable company requires you to connect a cable
box, make the connection as follows:
Cable or antenna (Rearof
VHF/UHF
Cable
Cable box (Rear of TV)
VHF/UHF
Cable ::_ _:_mml_
INL-_OUT
Cable box
Cable box and cable (KV-32V15/32V16/34V15C only)
I (Rear of TV)
Cable box _)_AUX
75-ohm coaxialcable TO
(not $uppliedl CONVERTER
CATV cable _)_
VHF/UHF
Pay cable TV systems use scrambled or encoded signals
requiring the cable box* in addition to the normal cable
connection.
* The cable box will be supplied by the cable company.
Note
• You cannot watch the signal through AUX connector as a
window picture.
Cable and antenna (KV-32V15/32V16/34V15C only)
(Rearof TV)
CAW cable :_),m_
AUX
TO
CONVERTER
Antenna cable
VHF/UHF
Note
• Do not connect anything to the TO CONVERTER connector in
this case.
Getting Started I 5
Connecting an antenna/cable TV system with a VCR
To connect your VCR to the TV, first check the model
number of your TV and select the corresponding
connection. For details on connection, see the
instruction manual of your VCR. In order to operate
PIP, a VCR must be connected to your TV. Before
making connection, disconnect the AC power cords of
the equipment to be connected.
After making these connections, you will be able to do
the following:
• View the playback of video tapes
• Record one TV program while viewing another
program
• Watch two TV programs at once using a window
picture (picture-in-picture)
Without a cable box
Cable
IN
VCR
AUDIO VIDEO
LINE !
?
Note
• To connect a monaural VCR, connect tl_e audio output ot the
VCR to AUDIO-L (mono} of VIDEO 1 IN on the TV.
VHF/UHF
I
I
VMC-810S/820S
(not supplied)
(RearofTV)
_ IDEO (yellow)
AUDIO-L (white)
AUDIO-R (red)
To an S video equipped VCR without a cable box
If your VCR has an S video output jack, hook up as
follows and then set S VIDEO to ON on your TV
(page12). It is set to ON at the factory.
Cable
VCR
::(_]_OUT AUDIO VrDEO s VIDEO
LINE
IN OUT
VHF/UHF
YC-15V/30V
(not supplied)
1
I
RK-74A
(not supplied)
(Rear of TV)
---I
/T! r?L2=
S VIDEO
AUDIO-L (white)
AUDIO-R (red)
6 Getting Started
With a cable box
VCR
OUT AUDIO VIDEO
LINE[_..
IN OIJT
Cable box l
Splitter
Note
• To connect a monaura] VCR, connect the audio output of the
VCR to AUDIO-L (mono) of VIDEO 1 IN on the "IV.
VHF/UHF
I
|
VMC410S/820S
(not supplied)
(RearofTV)
-- VIDEO (yellow)
AUDIO-L (white)
-- AUDIO-R (red)
To an S video equipped VCR with a cable box
(RearofTV)
VHF/UHF
VCR
Cable box l
Ca_ P'_ _ OUT
Splitter
_ YC-15V/30V
(not supplied)
I
I
RK-74A
(not supplied)
-- S-VIDEO
AUDIO-L (white)
-- AUDIO-R (red)
Note
• Video signals are composed of Y(luminance) and C (chroma)
signals. The Sconnection sends the two signals separately
preventing degradation, and gives better picture quality
compared to conventional connection.
Getting Started 7
Connecting a camcorder
• KV-27V15132S15132S16132V1$132Vl6134V15Conly
This connection is convenient for viewing a camcorder.
(Front of KV-32S15/32V16)
Video and
audio outputs VMC-810S/820S
(not supplied)
L
VIDE' W_
(yello
AUDIO-R
(red)
AUDIO-L
(white)
(Front of KV.27V15/32V15/32V16/34V15Q
STEREO/ u c_
VIDE w)-'-_ L_ AUDIO-R
(yello (red)
AUDIO-L
(white)
Note
* To connect a monaural camcorder, connect the audio output of
the VCR to AUOIO-L (mono) of VIDEO 2 INPUT on the TV.
Connecting an audio system
when cora_ecting audio equipment, see page 20 for
more information.
(RearofIV)
.
RK-74A(not supplied) --
AUDIO OUT-L (white)
AUDIO OUT-R (red)
Set the amplifier's
function to line input.
Line _
+u o
Connecting other Sony equipment with CONTROL S jack
• KV-27V15/32V15/32V16 only
Connect the supplied cable box controller (Cable
Mouse) to the CONTROL S OUT jack. Refer to the the
Cable Mouse's manual for details on the connection.
(RearofTV)
Make the following connections to control the TV and
connected equipment with one remote commander.
• To control other Sony equipment with the TV's remote
commander, connect the input of the equipment to
CONTROL S OUT jackon the TV.
• To control the TV with the remote commander of other
Sony equipment, connect the ou_ut of the equipment
to CONTROL S IN jack on the TV.
8 I Getting Started
Insert one size AA (R6) battery (supplied) by matching
the + and - on the battery to the diagram inside the
battery compartment.
Notes
• With normal use, the battery should last for approximately six
months.
• If you do not use the remote commander for an extended
period of time, remove the battery to avoid possible damage
from battery leakage.
• Do not handle the remote commander roughly. Do not drop it,
step on it or let it get wet.
• Do not place the remote commander in direct sunlight, near a
heater, or where the humidity is high.
Using the remote commander
The upper half of the remote commander has three
selectable operation modes, Each button in this area
has three different functions. You can select the mode
by sliding a selector on the left side.
For normal TV viewing
Variable indicator --
area
Indicates MODE selected
Set the selector to the
lowest position.
f
MUTING
f
_0 _0 _0
c::nO c:_O c::mO
I_0 <£mO _0
TVNI_O "_/ JUMP
C_D C_D C_D
(9®®
For operating video equipment
Indicates _ selected
Setthe selectorto the "_
middle position
F
c_nO c_nO c_nO
TV_ID[_ TV JUMP
Ci) (lIE)(lID
(D®®
For using the Picture-in-Picture feature
Indicates PIP selected --
Set the selector to the --
highest position.
F
MUTING
_0 _0 _0
cznO c:_O _E_O
mmO G_z_l
_#_ TV JUMP
(IED (EID (EID
Getting Started / g
You can set up your TV easily by using the AUTO SET
UP feature. It presets all the receivable channels.
To set up the TV manually, see "Setting cable TV on or
off" (page12) and "Presetting channels"(page12).
If the TV is set to a video input, you cannot execute
AUTO SET UP. Press TV/VIDEO or TV so that a
channel number appears.
(Front of KV-27S 15129RS 15/32S15/32S16}
(Front of KV-27V15132VIS/32V16134V15C)
SETUP I_/NIDEO -- VOLUME + --CHANNEL_ OPOWEFI
i[ • I I I . I • I • I_
J l' ' '1' I' I'1"
SET UP VOL+ CH- CH+ POWER
1 Press POWER to turn the "IV on.
OPOWER
g
2 Press SET UP on the front of the TV.
The menu appears.
SETUP
IOEMO 1
VOL+
AUTO SET UP : CH÷
FACTORY : CH-
PRESET
3 Press CH +.
AUTO PI_AM
"AUTO PROGRAM" appears on the screen and
the TV starts scanning and presetting channels
automatically. When all the receivable channels are
stored, "AUTO PROGRAM" disappears and the
lowest numbered channel is displayed. If the TV
receives cable TV channels, CATV is set to ON
automatically.
Notes
• If more than 90 seconds elapse after you press a button, the
menu disappears automatically,
• In case of using the AUX connector, preSs the TV button on the
remote commander first and make sure that "AUX" is
displayed beside the channel number on the screeen. Then
follow steps 2 and 3 above to perform AUTO SET LIP. (KV-
32V15/32V16 only)
DEMO: To browse the main functions,
Press VOL + in step 3. The functions and menus are
displayed one by one.
FACTORY PRESET: To restore the factory settings
when you are confused about the TV settings,
Press CH- in step 3. The settings of picture and sound
are restored to the factory setting.
Erasing or adding channels
After AUTO SET UP you can erase unnecessary
channels or add the channels you want. Preset channels
during the day rather than late at night, when some
channels may not be broadcasting.
_ (2zx3
+ t or 4 MENU
MODE RETURN
LOW po_ttfon_
1 Press MENU.
The main menu appears.
IVIOEO 1
AUOIO
SET UP
CRPIION VISIO_
se ._Exil_
10 Getting Started
(cofltmued)
_" Press + t or - t to move the cursor (1_) to
SET UP and press RETURN.
The SET UP menu appears.
_CH CAPTION/GUIDE
GH SET UP
3 Press + • or - • to move the cursor (1_)to CH
SET UP and press RETURN.
The CH SET UP menu appears.
CH SET UP I
• CABLE : ON
AUTO PROC_,_M
CH ERASE/ADD
_MENU
Use € _Jl_ Exit i_
4 Press + t or - _ to move the cursor (1_) to CH
ERASE/ADD and press RETURN.
The CH ERASE/ADD menu appears.
5 Erase and/or add the channel you want:
To erase an unwanted channel
(1) Make sure the cursor (1_) is beside ERASE.
(2) Press CH +/- to select the channel you
want to erase and,
Selected channel number
ICH ERASE/ADO
PERASE
Select INe channel
Use # _ Ex i I
To add a channel that you want
(1) Press + _ or - _, to move the cursor (b.) to ADD.
(2) Press the 0 - 9 buttons to select the channel you
want to add and press ENTER and,
®®®
®®®
®
Selected channel number
CH ERASEIADO _1
ERASE
Select the channel
Use € _mi Exit
(3) press RETURN.
The indication "+" appears beside the channel
number, showing that the channel is added to
the preset memory.
6 To erase end/or add other channels, repeat
step 5.
7 When you finish, press MENU.
Notes
• If you erase or add a VHF or UFLF channel, the cable TV
channel with the same number is also erased or added, and
vice vei<_.
• Erasing and adding channels are also available for the AUX
input. (KV-32V15/32V16/34V15C only)
(3) press RETURN.
The indication "-" appears beside the channel
number, showing that the channel is erased
from the preset memory.
Getting Started 11
Setting cable TV on or off Presetting channels
If you have connected the TV to a cable TV system, set
CABLE to ON, the factory setting. If not, set CABLE to
OFF. You do not have to do this procedure if you
execute AUTO SET UP (page 10). Do this procedure
only when you want to set it manually.
1 Press MENU.
2 Press + _ or - 4 to move the cursor (1_)to
SET UP and press RETURN.
3 Press + 4,or - • to move the cursor (1_)
to CH SET UP and press RETURN.
CH SET UP
-CABLE : ON
AUTO PR(_zCl/ZM
CH ERASEtAD_
:_MENU
Use €ltifiiIExitlj
4 Set CABLE to ON or OFF:
(1) Make sure the cursor (1_-)is beside CABLE and
press RETURN.
If the cursor is not beside tABLE, press + t' or
- • to move the cursor and press RETURN.
(2) Press + _.or - # to select ON or OFF and, press
RETURN.
CH SET UP
PCABLE : OFF
AUTO PROGRAM
CH ERASE/ADD
:_ENU
Use B_ Exit _
5 Press MENU to return to the original screen.
Note
• If CH SET UP appears in black, the TV is set to a video input
and you cannot select CABLE. Press TV/VIDEO or TV so that
a charmel number appears.
You can preset TV channels easily by using the AUTO
PROGRAM feature. You do not have to do this
procedure if you execute AUTO SET UP (page 10). Do
this procedure only when you want to set it manually.
1 Press MENU.
2 Press + t or - 4,to move the cursor (1_)
to SET UP and press RETURN.
3 Press + • or - • to move the cursor (1_)
to CH SET UP and press RETURN.
H SET UP
bCABLE : ON
AUTO pROGFIAM
CH ERASE/ADO
:_t4ENU
se €_i_ Exil _
4 Press + ) or - t to move the cursor (,)
to AUTO PROGRAM and press RETURN.
"AUTO PROGRAM" appears on the screen and the
TV starts scanning and presetting channels
automatically. When all the receivable channels are
stored, "AUTO PROGRAM" disappears and the
lowest numbered channel is displayed.
5 Press MENU to return to the original screen.
Notes
• If the CH SET UP menu appears in black, the TV is set to a
video input and you cannot select AUTO PROGRAM. Press
W/VIDEO or'IV so that a channel number appears.
• Presetting channels is also available for the AUX input. (KV-
32V15/32V16/34V15C only)
12 jGettingStarted
Setting S video on or off
You can change the S VIDEO menu to ON or OFF,
1 Press TVNIDEO to select VIDEO 1.
2 Press MENU.
3 Press + • or - 4 to move the cursor (1_)
to SET UP and press RETURN.
4 Press + _ or - t to move the cursor (1_)
to S VIDEO and press RETURN.
ET UP
CH CAPT ION/GUIDE
UH SET UP
I.S VIDEO : ON
:3MENU
se #_ Exit _i_
5 Press + t_or - • to select ON or OFF and
press RETURN.
SET UP
CH CAPTION/GUiDE
CH SET UP
"S VIDEO : OFF
:_MENU
Use 0_ Exil
6 Press MENU to return to the original screen.
Notes
• If S VIDEO appears in black, set a video input to VIDEO 1.
• If you set S VIDEO to ON, the TV automatically receive S
video signals whenever a VCR with S video is connected.
• KV-29RS15134V15Conly
If you prefer Spanish to English, you can change the
menu language.
+_°r-#_ MEN U
MODE RETURN
Low position
1 Press MENU.
The main menu appears.
_ I "VIDEO
AUDIO
SET UP
ENGLISH
Use €l_i_Exill
2 Press + • or - t to move the cursor (1_) to
ENGLISH and press RETURN.
VIDEO
AUDIO
SET UP
Use €_ Exit _i
,E_NGLISH
3 Press + ) or - t to select ESPAI_IOL and press
RETURN.
I VIDEO
AUDIO
AJU5 ES
"EEP_L
[UsBf#i_lSalifD
4 Press MENU to return to the original screen.
Note
• Certain parts of the ESPANOL menus remain in English.
Getting Started I 13
Operations
MUTING --
SLEEP
MODE
Low position --_
DISPLAY --
VOL +/- --
C_O c:_OC230
C_OC_O_
_3 c:_ocz_
DOC
sJ !U! L_
-- JUMP
0 - 9 buttons
-- ENTER
-- CH +/-
1 press POWER (TV) to turn the TV on.
If "VIDEO" appears on the screen, press the TV/
VIDEO or TV button so that a channel number
appears.
2 Select the channel you want:
Toselect a channel directly
Press the 0- 9 buttons and then press ENTER.
Toscanthrough channels
Press CH +/- until the channel you want appears,
®®®
®®
®
The channel can also be selected without pressing
ENTER.
3 Press VOL +1- to adjust the volume.
Note
• Set the CABLE BOX/TV selector to TV.
14 lOPerati°ns
VOLUME
Switching quickly between two
channels
Press JUMP.
The channel you watched previously appears.
JUMP
Pressing JUMP again switches back the channel.
Muting the sound
Press MUTING.
"MUTING" appears on the screen.
MUTING
To restore the sound, press MUTING again, or press
VOL +.
Displaying on-screen information
Use this feature to check the channel number, channel
caption (if set), and MTS mode (if SAP is selected).
Press DISPLAY.
DISPLAY
To cancel the display, press DISPLAY again.
Setting the Sleep Timer
The TV stays on for the length of time you specify and
then shuts off automatically.
Press SLEEP repeatedly until the time (minutes)
you want appears.
Each time you press SLEEP, the time changes as
follows: 30 _ 60 _ 90 ---*OFF.
To cancel the Sleep Timer, press SLEEP repeatedly
until "SLEEP OFF" appears, or turn the TV off.
Changing the VHF/UHF input to the
AUX input
a KV.32V15/32V16/34V15C only
Press "IV.
TV
%
Pressing TV again switches back to the previous input.
I
Changing the window picture input
mode
The Picture-in-Picture (PIP) feature allows you to
watch both the main picture and a window picture
simultaneously.
Your TV must be connected to a VCR to enjoy this
feature (_cept KV-32V15/32V16/34V15C). See
"Connecting an antenna/cable TV system with a VCR"
(page 6 and 7) for connections.
SWAP
POSITION PIP
FREEZE TV/VIDEO
AUDIO CH +/-
PIP
High position
Displaying a window picture
Press PIP.
Input-source mode or "IV
channel for the main picture
Main pictUree l"=__
(1W);dsi°welPi(tUrlnpu,-sourcelm(der or TV ,
channel for the window picture
Press PIP again to display a smaller window
picture.
To remove the windo_a } icture, press PIP again.
Notes
• If the main picture is not receiving an image, the window
picture may be in black and white.
• The windo_ picture may be affected by the condition of the
main picture.
• The window picture s_und is also output h'om the
VARIABLE/FIX AUDIO OUT jacks when you listen to it.
• In order to operate PIP, your VCR must be turned (_n (l'.w-t,/it
KV-32VI5132VI6/34V15C).
Press TV/VIDEO in the PIP control area to select
the input mode.
Each time you press TV/VIDEO, "TV', "VIDEO 1",
"VIDEO 2" and "VIDEO 3 (except for KV-27S15/
29RS15)" appear in sequence.
A window picture will appear in the same input mode
as the last time you used PIP.
Note
• If you use one of the connections from page 6, your PIP input
source is a VCR. If you use one of the connections from page
7, your PIP input source is a VCR or cable box.
Listening to the sound of the window
picture
Press AUDIO.
The ._ display appears for a few seconds, indicating
that the window picture sound is being received.
To restore the main picture sound, press AUDIO again.
Changing W channels in the window
picture
Press CH +/- in the PIP €ontrol area.
Operations I 15
Changing the position of the window
picture
Press POSITION.
Each time you press POSITION, the window picture
will move counterclockwise on the screen.
Freezing the window picture
This feature is useful when you want to write down a
recipe from a cooking program, a displayed address or
a phone number and so on,
Press FREEZE.
To restore the normal screen, press FREEZE again.
II
Swapping the main and window
pictures
Press SWAP.
Each time you press SWAP, the images from the main
and window pictures switch places along with the
sound.
t
I VIDEO 1
::.* 6
Note
• T_e ch_ra3els being received through the AUX jack cannot be
displayed as a window picture (KV-32VIS/32V16/34V15C only).
When watching TV programs, you can adjust the
quality of the picture to suit your taste.
You can adjust the picture of video input(s) as well.
These settings are stored separately from those for the
TV picture.
+0or_0_
RESET MENU
MODE RETURN
1 Press MENU.
2 Make sure the cursor (1_) is beside VIDEO
and press RETURN.
V I DEO
PPICTUflE IIIIIIIIItlEIM
HUE _#"""
COLOR IWlII""
BRleHT
SHARP UmlI-----
_ENU
Use ¢1i_ Exit W
3 Select the item you want to adjust.
For example:
(l) To adjust brightness, press + t1"or - • to select
BRIGHT and,
IVIDEO I
PICTURE mmamlm=
COLOR IIIII-'---
='BRIGHT IIIIIIII1_,
SHARP
:_NU
Us_ € _i Exl[ ii
BRIGHTNESS
(2) press RETURN.
16 Operations
4 Adjust the selected item:
(1) Press + t or - • to adjust the item and,
I
(_(_ , 6RIGHTNESS
(2) press RETURN.
The new setting appears in the VIDEO menu.
VIDEO
(_ _BRIGHT:_MENuSHARpCOLGRHuEPICTURE_EllE'="_l
Use #_i Exit _i_
For details on each item, see "Description of
adjustable items" below.
5 To adjust other items, repeat steps 3 and 4.
Description of adjustable items
Item Press + • to
PICTURE Increase picture
contrast and give
vivid color.
HUE Make skin tones
become greenish.
COLOR
BRIGHT
SHARP
Press - • to
Decrease picture
contrast and give soft
color.
Make skin tones
become purplish.
Increase color intensity. Decrease color intensity.
Brighten the picture. . Dar.ken the picture.
Sharpen the picture. Soften the picture.
To restore the factory settings
Press RESETwhile the VIDEO menu is displayed.
All the settings except for PICTURE are restored to the
factory settings.
• KV-27V15132V15132V16134V15C only
The LUMISPONDER feature adjusts the brightness of
the screen automatically according to the ambient
brightness. The LUMISPONDER function
automatically adjusts the level set by the user in the
VIDEO menu to the standard.
÷•or-• _ MENU
MODE _ RETURN
Low position
1 Press MENU.
2 Press + • or - • to select VIDEO and press
RETURN.
3 Press + * or - • to select LUMISPONDER and
press RETURN.
iv00i
PI CIURE
@ _L_ _
BRIGHT il_
SHARP _
bLUMISPI_IDER : OFF
:_ENU
4 Press + 4,or - • to select ON or OFF and
press RETURN.
lVlOEO I
PJCTGHE(_ BRIGHT llII-"---
SHARP _
,_LLIMI SPOi_OER : ON
:I_Hu
Operations17
You can adjust the quality of the TV sound to suit your
taste. You can adjust the sound of video input(s) as
well. These settings are stored separately from those
for the TV sound.
C:D C:D_
Feor-t
RESET MENU
MODE RETURN
Low position
1 Press MENU.
2 Press + • or - t to select AUDIO and press
RETURN.
BALANCE----4....
(_ SURROUNO:OFF
Mrs: MAIN
SPEAKER SWITCH
' ;_NJ
3 Select the item you want to adjust.
For example:
(1) To adjust bass, press + # or - • to select BASS
and,
i_ole
_0 TREBLE
='BASS Selle,.,,.-
BALANCE_
(_(_ SURROUNO :OFF
MrS: MAIN
SPEAKER SWITCH
:_ENU
(2) press RETURN.
4 Adjust the selected item:
(1) Press+ # or - $ to adjust the item and,
BASS
I
(2) press RETURN.
The new setting appears in the AUDIO menu.
AUDIO ]
TREBLE
.sAssSS------
BAL_@ICE--"4-----
Sli_D :OFF
MTE: MAIN
SPEAKER SWITCH
NU
For details on each item, see "Description of
adjustable items" below.
5 To adjust other items, repeat steps 3 and 4
above,
TREBLE Increase the treble
response,
BASS Increase the bass
response.
BALANCE Emphasize the right
speaker's volume.
Description of adjustable items
Item Press + • to Press - # to
Decrease the treble
response.
Decrease the bass
response.
Emphasize the left
speaker's volume.
To restore the factory settings
Press RESET while the AUDIO menu is displayed.
Note
• When SPEAKER (page 20) is OFF and AUDIO OUT (page 20)
is FIXED condition, the sound is set to mid-level and it cannot
be adjusted.
18 JOperations
SURROUND feature simulates sound reproduction
with the atmosphere of a movie theater or a concert
hall. Surround sound is only effective for stereo
programs.
MODE
Low position
1 Press MENU.
MENU
RETURN
2 Press + • or - t to select AUDIO and press
RETURN.
3 Press + • or - 4 to select SURROUND and
press RETURN.
IAUDIO I
TREBLE _
BASS
BALANCE_--,I-,---,
,SURROL_ND:OFF
MT$: MAIN
SPEAKER _ITCH
:_ENU
4 Press ÷ ) or - • to select ON and press
RETURN.
IAUDIO 1
TREBLE
BASS
BALARCE"-I
>SURROUND:ON
kITS: MAIN
SPEAKER_ITCH
_NU
The Multichannel TV Sound (MTS) feature allows you
to enioy stereo sound or Second Audio Programs (SAP)
at your choice. The initial setting is stereo sound
(MAIN).
+_or-_ _ MENU
MODE _ RETURN
LOW position
1 Press MENU.
2 Press + • or - t to select AUDIO and press
RETURN.
3 Press + t or - • to select MTS and press
RETURN.
IAUDIO I
TREBLE
BASS''--"
BALAi_E
_@ SURROUND:OFF
_.k_S: _JIA_R
SPEAKER _ITCH
:_ENU
4 Press + t_or - • to select MAIN, SAP, or
MONO and press RETURN.
_eDlO
TREBLE
BASS
BALANCE'"4""_
BURROUND:OFF
,_TS: SAP
SPEAKER :SWITCH
Choose
MAIN
SAP
MONO
To
Listen to stereo sound.
The STEREO indicator on the TV lights up
while a stereO broadcast is received.
Listen to bilingual programs.
The sound of non-SAP programs will be
muted when SAP is selected.
Reduce noise during stereo broadcasts.
Note
• Stereo and SAP sounds are sub)ect to program sources.
Operations I 19
You may switch off the TV speakers when, for
example, you want to listen to the sound through a
stereo system.
+_or-__MENU
MODE _:_ RETURN
1 Press MENU•
2 Press + t or - • to select AUDIO and press
RETURN.
3 Press + _ or - t to select SPEAKER SWITCH
and press RETURN.
SPEP,KER SWITCH
4 Make sure the cursor (1_) is beside SPEAKER
and press RETURN.
I 1
SPEAKER _ITCH
_]_ _'SPEAKER : ON
5 Press + • or - • to select ON or OFF and
press RETURN.
c_. Q_ _;oOuTvAo
20 I Operations
You can select audio out to variable or fixed when
SPEAKER is set to OFF.
Audio out is variable when SPEAKER is set to ON.
+)or-t _MENU
MODE RETURN
LOW position
1 Press MENU.
2 Press + • or - • to select AUDIO and press
RETURN.
3 Press + t or - • to select SPEAKER SWITCH
and press RETURN.
_O _
SPEAKER _NI TCH
='SPEAKER : OFF
_,o OUT: v,_
4 press + • or - t to select AUDIO OUT and
press RETURN.
_Q _
SPEAKER SWITCH I
SPEAKER : OFF
5 Press + * or - • to select VAR or FIXED and
press RETURN.
_O _
SPEAKER SWJTCH :1
SPEAKER : OFF
"AUDIO OUT FIXED
::t,_ NU
VAR: Sound output varied according to the TV
settings. You can adjust the volume, bass,
treble and balance.
FIXED: Sound output is always fixed to a certain
level. The volume, bass, treble and balance
are also fixed to the factory settings.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Hitachi 55FX20B Owner's manual
-
Zenith SLS7253S Owner's manual
-
-
-
Akai PT4298HD Owner's manual
-
-
-
-
RetroSound Exile LED Monitor Owner's manual
-
Gibraltar Building Products CHADS-1/8 Operating instructions