Hitachi 36FX48B Operating instructions

Category
LCD TVs
Type
Operating instructions

This manual is also suitable for

3olid State Color TV
_)PERATING GUID
IMPORTANT SAFEGUARDS
FIRST TIME USE
THE GENIUS
REMOTE CONTROL
2-4
5-20
21-37
ULTRATEC BIT-MAP
ON-SCREEN DISPLAY
38-61
K USEFUL INFORMATION INDEX 62-67
IMPORTANT
Followall warningsand instructionsmarked on this color television.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUAUFiED SERVICE PERSONNEL
The lightning flash with arrowhead symbol, within an equilateral tri-
angle, is intended to alert the user to the presence of uninsulated
=dangerous voltage" within the product's enclosure g_atmay be of a
sufficient magnitude to constitute a dsk of electric shock to persons.
The exclamation point within an equilateral triangle, is intended to
alert the user to the presence of Important operating and maJnte-
nence (servicing) instructions in the literature accompanying the
appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS COLOR TELEVISION TO RAIN OR MOISTURE.
I NOTE:
There are no user serviceable parts inside the television.
Model and serial numbers are indicated on back side of the television.
I
CAUTION:
Adjust only those controls that are covered in the instructions, as improper
changes or modifications not expressly approved by Hitachi could void the user's
authority to operate the TV.
POWER SOURCE
This HITACHI color television is designed to operate on 120 volts 60Hz, AC current.
Insert power cord into a 120 volt 60Hz outlet.
TO PREVENT ELECTRIC SHOCK, DO NOT USE THE TELEVISION'S (POLARIZED) PLUG
WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES
AND GROUND TERMINAL CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
NEVER CONNECT THE TELEVISION TO 50HZ, DIRECT CURRENT, OR ANYTHING OTHER
THAN THE SPECIFIED VOLTAGE.
I NOTE:
This television receiverwilldisplay television closed captioning, (r_ or I_), in accordance with para- I
graph 15.119 of the FCC rules.
I
CAUTION:
I
Never remove the back cover of the television as this can expose you to very high voltages and other hazards. I
Ifthe television does notoperate properly, unplugthe television and call your authorized dealer or service shop.
I
SAFETY TIPS
IMPORTANT SAFEGUARDS
CAUTION: Read all of these instructions.
Save these instructions for later use.
Follow all warnings and instructions marked
on the television.
SAFETY POINTS YOU SHOULD KNOW ABOUT
YOUR HITACHI COLOR TELEVISION
Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions.
Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustratessafety tips which
will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI television.
Please fill out your warranty card and mail it to HITACHI. This will enable HITACHI to notify you promptly in the improbable event that a safety
problem should be discovered in your product model.
FOR YOUR PERSONAL SAFETY
1. This television set isequipped with a
polarized allemating-oummt line ptug
(a plug having one blade wider than
the other.) This plug will fit into the
power outlet only one way. This is a
safely feature. If you are unable to
insert the plug fully into the outlet, try
reversing the i_u9. If the plug should
still fall to fit. contact your electrician
1o replace your obsolete outlet. Do
not defeat _ safety purpose OI the
peismed i_,ug.
2. When the power cord or plug is
damaged or frayed, unplug the
television from the wall outlet and
refer servicing to qualified service
personnel.
3. Do not overload wall outlets and
exlensidn cords as this can result in
fire or electric shock.
4. Do not allow anything to rest on or
roll over the power cord, and do not
place the television where the
power cord is subject to traffic or
abuse. This may result in a shock
or fire hazard.
Oono--o--h OOn --ro
television yourself as opening or wall outlet before cleaning. Use a
removing covers may expose you damp cloth for cleaning. Do not
to dangerous voltage or other use liquid or aerosol cleaners.
hazards. Refer all servicing to
qualified service personnel.
5.
Never push objects of any kind into
the televisiun's cabinet slots as they
may touch dangerous voltage points
or short out parts that could result in
a fire or eleotdc shock. Never spill
liquid of any kind on the television.
It the television has been dropped or
the cabinet has been damaged,
unplug the television from the wall
outlet and refer sewicing to qualified
service personnel.
If liquid has been spilled into the
television set. unplug it from the
wall outlet and refer service to
qualified service personnel,
DO not subject your television to
impact of any kind. Be careful not to
damage the picture tube sudace.
11-1. Do not place the television on an
unstable cart, stand, or table. The
television may fall, causing
serious injury to child or an
adult, and serious damage to the
appliance. Ueaonlywithacartor
stand recommended by the
manufacturer, or sold wi_ the
television. Wal or shelf mounting
should follow the menutacturer's
instructions, and should use a
mounting kit approved by the
manufacturer.
11-2. An applience and cart combination
should be moved with care.
Quick slops, excessive force, and
uneven sudaces may cause the
appliance end cart combination
to overturn.
PROTECTION AND LOCATION OF YOUR TELEVISION
12. Do not use the lelevision near
water, for example, near a bathtub,
washbowl, kitchen sink. or laundry
tub, in a wet basement, or near a
swimming pool. etc.
Never expose the television to
rain or water. If the set has been
exposed to rain or water, unplug
television from wall outlet and
refer to qualified service person-
nel.
13. Choose a place where light
(artificial or sunlight) does not
shine directly on the screen.
14. Avoid dusty places. Accumulated
dust inside the chassis may cause
failure of the television when high
humidity persists.
15. The television has slots or openings
in the cabinet for ventilation
purposes which provide reliable
operation of the receiver and
protect the television from
overheating. These openings must
not be blocked or covered.
Never cover the slots or openings
with cloth or other material.
Never block the bottom ventilation I_
slots of the television by placing it on
a bed, sofa, rug, etc.
Nevor pl&ce the television near or _'f,'_*"*,'_
over a radiator or heat register.
Never p/ace the television in a built-in
enclosure oniass proper ventilation
is provided.
3
SAFETY TIPS'
PROTECTION AND LOCATION OF YOUR TELEVISION
16-1. Ifan outside antenna isconnected
to the television, be sure the
antenna system is grounded so as
to provide some protection against
voltage surges and betH-up static
charges. Section 810 of the
National Electrical Code, NFPA
No. 70-1975, provides information
with respect to proper grounding
of the mast and supporting
structure, grounding of the lea@in
wire to an antenna discharge unit,
size of grounding conductors,
location of antenna discharge unit
connection to grounding
electrode, and requirements for
the grounding electrode.
16-2. Nole to CATV system installer:
(Only for television with CATV
reception). This reminder is
provided to call the CATV system
insteller's attention to Article
820-40 of the NEC that provides
guidelines for proper grounding
and, in particular, specifies that
the cable ground shall be
connected to the grounding
system of the building, as close
to the point of cable entry as
practical.
OPERATION OF YOUR TELEVISION
19. This television should be operat-
ed only from the type of power
source indicated on the marking o_ ,_/_
label. If you are not sure of the
type of power supply at your
home. consult your dealer or local
power company. For televisions
designed to operate from battery
power, refer to the operating
instructions.
T
NEeMlX_'W. B.ECTI_.K_
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL
CODE INSTRUCTIONS.
17. An outside antenna system should
not be located in the vicinity of
overhead power lines or other
electrical lights or power circuits.
or where it can fall into such power T _
lines or circuits. Wtlen installing an II ._x /'DO o'_1_
outside antenna system, extreme _ _,_o, I D J I
care should be taken to keep from _ -L--.._J-t.
touching such power lines or
circuits as contact with them might
be fatal.
18. For added protection for the
television during a lightning storm.
or when it is unused for long
periods of time, unplug it from the
wall outlet and disconnect antenna.
This will prevent damage due to
lightning and power-line surges.
20.
If the television does not operate
normally by folowing the obeceting
instrucifons, unplug the telmCslen
from the wall outlet end refer *---"-_ €''%*"_
servicing to qualified service
personnel. Adjust only those
controls that are covered in the
insuuctk_ns as improper adjustment
of other controls may result in
damage and wilt often require
extensive work by qualified
sennus technician to restore the
televislen to normal operetiork
21. If your television is to remain p_ __.
unused for a period of time. (such
as when going on a holiday), turn
the television OFF and unplug it
from the wall outlet.
IF THE TELEVISION DOES NOT OPERATE PROPERLY
22. If you are unable to restore
normal operation by following
the detailed procedure in your
operating instructions, do not
attempt any further adjustments.
Unplug the television and call
your dealer or service technician.
23. Whenever the television is
damaged or fails, or if there is a
distinct change in performance
that indicates a need for service.
unplug the television and hove it
checked by a qualified service
technician.
24. It is normal for some televisions to
make occasional snapping or
popping sounds, particularly v/nan
being turned on or off. if the
snapping or popping is continuous
or frequent, unplug the set and
consult your dealer or service
technician.
FOR SERVICING AND MODIFICATION
25. Do not use attachments not
recommended by the television
manu/ecturer as they may cause
hazards.
j,_ o 26. If replacement beds ere required, 27. Upon completion of any service or ._. ,_,
be sure the service technician has repairs Io the television, ask the
used replacement parts specified by service technician to perform
the manufacturer that have the routine safety checks to determine
same charectenstlos es the original that the television is in sate
bert. Unauthorized substitutions operatingsonditlon.
may result in fire. electric shock, or
olhe¢ hazards.
PICTURE CAUTIONS
Picture Burn Prevention
Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and
other fixed (non-moving) patterns can cause permanent damage to television receivers. Such =PATTERN BURNS"
constitutemisuse and are NOT COVERED byyour HITACHI FactoryWarranty.
When using Picture-in-Picturefunction,the sub-pictureshouldnot be left permanently in one cornerof the screen or a
"PA'I-I'ERN BURN" may develop over a long period of time.
Public Viewing of Copyrighted Material
Public viewing of programs broadcast by TV stationsand cable companies, as well as programsfrom other sources, may
require priorauthorizationfrom the broadcaster or owner of the video program material.
4
ACCESSORIES
Check that you have the following accessories before disposingofthe packing material.
1. Remote Control Unit (See Part No. below)
2. Two "AA" size, 1.5V batteries (For Remote Control Unit).
For information regarding how to obtain these accessories, please call TOLL FREE 1-800-448-2244 for the nearest HITACHI
Authorized parts Distributorin the United States. For Alaska and Hawaii, please contact your nearest HITACHI regional office.
PARTS NAME
36UX58B
CLU-612MP
REMOTE CONTROL
PART NO.
HL00712
36FX48B
32FX48B
CLU-431UI
REMOTE CONTROL
32V TELEVISION STAND
SP316B
(Notincluded,orderseparately)
32V TELEVISION STAND
SP317B
(Notincluded,orderseparately)
36V TELEVISION STAND
SP351B
(Notincluded,orderseparately)
.HL00721
H530022
H530023
(upgrade)
H530024
.=.:,
(3_(3DGD
(3D(3_(3D
CD(3D(3D
CLU-612MP
ILLUSTRATION
I
0000
_ €_TP,m
CD CDCD
_CDCD
CLU-431U!
CUSTOM HITACHI
TELEVISION STAND
Excellent for VCR and video-
tape storage. Special fea-
tures includes curved smoke
glass doors and an
adjustable shelf.
Available in Black.
J_Ik CAUTION:
Television stand models SP316B and SP317B are designed for use only with a 32 inch or smaller television
set. Television stand model SP351B is designed for use with a 36 inch or smaller television set. Use of a
smaller stand, a non Hitachi recommended stand or a generic stand may result in instability,causing possible
injury.
REMOTE CONTROL BATTERY INSTALLATION
AND REPLACEMENT
1. Open the battery cover of the remote controlby
pushing the notched part of the cover with your
fingers.
2. Insert two new "AA" size batteries for the remote
control. When replacing old batteries, push
them towards the springs and lift them out.
3. Match the batteries to the (+) and (-) marks in
the battery compartment.
4. Replace the cover.
BOTTOM VIEW
Push in and lift up on tab to
remove back cover.
CAUTION:
1.
2.
3.
4.
If your television set is to remain unused for a long period of time, for instance when you go on vacation, unplug the television from the wall
outlet.
Do not subject the remote control to shocks such as dropping it on the floor, etc. Precision parts may be damaged.
Do not allow the remote control to become wet and avoid placing it in areas of high humidity. Do not leave it on or near a heater. Excess heat
or moisture may cause the unit to cease operation.
If the batteries become exhausted, remote controloperation may become erratic or stop altogether. Replace the old batteries with new "AA"
type.
NOTES:
1. The CHANNEL NO., VOLUME and OFF TIMER indicator are not displayed simultaneously.
2. To operate your TV, point the remote control at the remote sensor of the TV.
HOW TO SET UP YOUR NEW HITACHI COLOR TV
ANTENNA
Unless your TV is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is
recommended for best performance. However, if you are located in an exceptionally good signal area that isfree from interferenceand
multipleimage ghosts, an indoor antenna may be sufficient.
LOCATION
Select an area where sunlight or bright indoor illuminationwill not fall directly on the picture screen. Also, be sure that the location
selected allows a free flow of air to and from the perforated back cover of the set.
To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can
become excessively hot, for example, in direct sunlightor near a heating appliance, etc.
VIEWING
The major benefit of the HITACHI Color Television is its large viewing screen. To see this large screen at its best, test variouslocations
in the room to findthe optimum spot for viewing. The drawings give several suggestions.
The best picture is seen by sitting directlyin front of the "IV and about 6 to 9 feet from the screen. During daylight hours, reflections from
outside light may appear on the screen. If so, drapes or screens can be used to reduce the reflection or the "IV can be located in a
different section of the room.
If the "FV'saudio output will be connected to a Hi-Fi system's external speakers, the best audio performance will be obtained byplacing
the speakers equidistant from each side of the receiver cabinet and as close as possible to the height of the picturescreen center. For
best stereo separation, place the external speakers at least four feet from the side of the "IV, place the surroundspeakers to the side
or behind the viewing area. Differences in room sizes and acoustical environments will require some experimentation with speaker
placement for best performance.
4' MINIMUM
4' MINIMUM
I ,_CAUTION:
Magnetic fields, such as those of external speakers, may cause the picture to distort if they are placed too
close to the television. Move the magnetic field source away from the television until there is no picture
distortion.
I
HOOK-UP CABLES AND CONNECTORS
Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors.
For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell
audio/videoproducts. Below are illustrations and names ofcommon connectors. Before purchasing any cables, be sure of the output
and inputconnectortypes required by the various components and the length of each cable.
300-Ohm Twin Lead Connector
This outdoor antenna cable must be connected to an antenna
adapter (300-Ohm to 75-Ohm).
"F" Type 75-Ohm Coaxial Antenna Connector
For connectingRF signals (antenna or cableTV) to the antenna
jack on the television.
Phono Connector
Used on all standard video and audio cables which connect to
inputsand outputslocated onthe television's rear jack panel and
front control panel.
S-Video (Super Video) Connector
This connector is used on camcorders, VCRs, and laserdisc
players with an S-Video feature in place of the standard video
cable to produce a high quality picture.
Antenna Connections
These sets are equipped with one VHF/UHF antenna terminal. The VHF/UHF terminal can be used for normal TV, cable TV (CATV), a
TV game, etc.
1.
VHF (75-Ohm) antenna/CAW (Cable TV)
When using a 75-Ohm coaxial cable system, connect
the outdoor antenna or CATV coaxial cable to the ANT
A (75-Ohm) terminal. If you have a second antenna or
cableTV system, connect the coaxial cable to the ANT
B terminal.
Tooutdoor or CATVcable
L VHFAJHF ,,
75Ohm I I Q,hlL _L t (disconnect)
C°axia_...jb= LI,_ _@, (_L.J ._F Adapt°r
2. VHF (300-Ohm) antennaiUHF antenna
When using a 300-Ohm twin lead from an outdoor
antenna disconnect the (VHF or UHF) indoor antenna
leads from screws of the (VHF or UHF) adaptor and
connect outdoor (VHF or UHF) antenna leads to these
screws of a (VHF of UHF) adaptor.
To outdoor VHF
t or UHF Antenna
_llL _ (connect)
_.,_._Adaptor
3. When both VHF and UHF antennas are connected
Attachan optionalANTENNA MIXER to the TV antenna
terminal and connectthe cables to the ANTENNA
MIXER.
VHF/UHF
(RearofTV set)
ToUHF Antenna II_
To
outdoor
.,,._.__ 4"_VHFAntenna
ANTENNA
MIXER
Notes:
1. If an outdoor antenna/CATV is used, disconnect the
indoor antenna. Ghosting and poor reception may
result if both the indoor and outdoor antennas/CATV
are connected at the same time.
2. Consultyour dealer or service store for the ANTENNA
MIXER and (VHF or UHF) adaptor.
3. The special converter (decoder) willbe supplied by the
cable company.
FRONT PANEL CONTROLS FOR 32FX48B
FRONT VIEW
L J _ I Iooeeocn| I
I
HOW TO OPEN THE DOOR
I m
1. Push on "_"
2. Pullthe door toward the front to open it.
O
Dual Tuner PIP I
(_) RemoteControl
InfraredSensor
FRONT INPUT JACKS
I I INPUT3 I J
0 0 0
(_) Video:3 Input-_
0 @ ®
Volume
Button Butbm Burns
VOL- VOI.* C_ Oe.
0000000
MENU--I I I I I I
.4
Exrr.-----J I I I I
CURSOR
See pages 25 and 26 for
MENU, CURSOR, and EXIT
buttonoperations.
A detailed explanation of the circled numbers ison page 11.
FRONT PANEL CONTROLS FOR 36UX58B AND 36FX48B
FRONT VIEW
For 36UX58B Only
/.1111111/IBII
I
@ @ ® ®
InmUF_xit Volume Channel
Button Buttons Butto_
--1 _-I r-h I
Vvol.& ot
O00QO00
MENUEX=r ,4 I_
r
I Dual Tuner PIP (O)',-- .,_.,,,_
MENUJ I I I I I
CURSOR
Remote Control
Infrared Sensor
See pages 25 and 26 for
MENU, CURSOR, and EXIT
button operations.
FRONTINPUTJACKS
0000 0 O0
A detailed explanation of the circled numbers is on page 11.
i
I NOTE: (e)°SOl, INI} RErRIEVAL _ is for MODEL 36UX58B only.
10
FRONT PANEL JACKS AND CONNECTIONS
I I
INPUT/EXIT button
Press this buttonto selectthe currentantenna source of VIDEO: 1,2, 3. Your selectionis shown in the top rightcomer ofthe screen.
This button also serves as the EXIT buttonwhen in MENU mode.
VOLUME Level
Press these buttons for your desired sound level. The volume level will be displayed on the TV screen.
CHANNEL Selector
Press these buttons untilthe desired channel appears in the top right corner of the TV screen.
POWER Button
Press this buttonto tum the TV on or off.
NOTE:
Your HITACHI TV will appear to be turned off ifthere is no video input when VIDEO: 1, 2, or 3 isselected. If you have
no inputto VIDEO: 1, 2, or 3, pressthe INPUT button until the normal broadcast picture appears. (See page 25.)
If the picture does not appear, the power is OFF.
®
®
REMOTE CONTROL INFRARED Sensor
Point your remote control at this area when selecting channels, adjusting volume, etc.
FRONT INPUT JACKS
Use these audio/video jacks for a quick hook-up from a camcorder or VCR to instantlyview your favorite show or new recording.
Press the INPUT button until VIDEO:3 appears in the top rightcorner of the TV screen. If you have mono sound, insert the audio
cable intothe left channel jack.
I NOTE: Front panel control CURSOR operation will not appear the FAMILY FAVORITES channel function. I
11
FRONT PANEL JACKS AND CONNECTIONS
The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following
examples:
Video Camera
0
_ OUTPUT
Insert audio cable
into left channel
for mono sound
/
INPUT
°°°
/
Video Camera
OUTPUT
INPUT
/ /
NPUT f
OO
I°°°° Y
S-VHS V L R
OUTPUT |
(BackolVCR)
I NOTE:
t
Completely insert connection cord plugs when connectingto front panel jacks. If you do not,the picture that is played
back may be abnormal.
12
REAR PANEL JACKS
Ili.o]11
4 ÷
VHF/UHF
ANTENNA TERMINALS
(9
lJ
36FX48B and 32FX48B
/INT IJ TO ANlrA
o _ _Q
L._
Q
INPUT TERMINALS
I
I I
(
I WE,AK STRONG
" _ 8-VIDEO
AUDIO TO HIFI _,_ INPUT
OUTPUT TERMINALS
36FX48B only_,
I
I
(_) GEO_GNETISM J
CORRECTION z
I
r
36UX58B
(_) MONITOR OUT '
INPUT TERMINALS
I, I
1_;16°16°1
i t=oz_/.ll_zl l
IOflOilOil<
/o_ .1o4 '1,
I
I
INPUT
) AUDIO TO HIFI OUTPUT TERMINALS
13
REAR PANEL JACKS
(_ Antenna Inputs
The remote control allows you to switch between two separate 75-Ohm RF antenna inputs, ANT A and ANT B. ANT A inputcan
be displayed as a main picture or sub-picture. ANT B can only be displayed as a main picture. (ANT B cannot be displayed as a
sub-picture.) The antenna output labeled =TOCONVERTER" allows the ANT A connection to pass directly to a different source
such as a cable box.
O Audio/Video Inputs 1, 2
The INPUT button will step through each video source and antenna source input each time it is pressed. Use the audio and video
inputs to connect extemal devices, such as VCRs, camcorders, laserdisc players, etc. (If you have mono sound, insertthe audio
cable intothe left channel jack.)
(_) Monitor Out (36UX58B ONLY)
These jacks provide fixed audio and video signals which are used for recording.
(_) Audio to HI-FI
These jacks provide variable audio output to a separate stereo amplifier. With this connection, the audio to the stereo can be
controlledby the television's main volume. Use these jacks for the SURROUND Leftand Right channels. (See page 20)
(_ S-Video
Inputs 1 provide S-Video (Super Video) jacks forconnecting equipment with S-Video outputcapability.
(_ Goemagnetism Correction (36FX48B Only)
This TV has a super-large color picture tube. The effects of geomagnetism may cause an uneven (partially) colored picture
depending on the directionthe TV isfacing. Adjust the TV as follows for best performance:
1. Turn the Power uO_.
2. Decide on the installation position and directionof the TV. Check the directionthe TV isfacing at this time.
3. Set the DIRECTION and STRENGTH switches (on back of the TV) according to the directionof the screen as shown in the
table.
DIRECTION
FACING
SCREEN DIRECTION
North
Northeast
East
Southeast
South
Southwest
West
Northwest
SWITCH
DIRECTION
N
*E/W
E/W
**F.JVV
s
**E/W
E/W
*F_AN
STRENGTH
STRONG
WEAK
WEAK
WEAK
STRONG
WEAK
WEAK
WEAK
*ifthe Screenisfacinga Northerlydirection,setto"N'.
**IftheScreenisfacinga Southerlydirection,set to"S'.
4. After setting the switches, place the TV in the decided location.
5. After relocating the TV, tum the power =ON"and checkto make sure that the screen color (especially at the corners) iseven.
Depending on the installation location (especially where it is susceptible to goemagnetism, for example, in a reinforced concrete
building), in this case, set the DIRECTION and STRENGTH switches to set the optimum picture.
6. In certain areas, if the screen points North or South, color unevenness may be reduced when the STRENGTH switch is set to
STRONG rather than WEAK.
I NOTE: If you move your TV, the DIRECTION and STRENGTH switches may need to be reset. I
I
TIPS ON REAR PANEL CONNECTIONS
The S-Video connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these con-
nections in place of the standard video connection if your device has this feature.
If your device has only one audio output (mono sound), connect it to the left audio jack on the television.
Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables.
A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output (INPUT: 1
in the example on page 15 or 16.) Refer to your VCR operating guide for more information on line input-output connections.
14
REAR PANEL CONNECTIONS 136FX48B AND 32FX48B I
IJ
W
o_ Iol
StereoSystemAmpli6er
Ouside antenna or
cable "IV coaxial cable
l [,_-2-Way signal
J " splitter
_I
CableTVBox
IF OO
1_1o _v_ °L
!
Typicalfull feature setup. Follow connections that pertain to your personal entertainment system.
15
I
REAR PANEL CONNECTIONS 136UX58B )
I
Ouside antenna or
cable TV coaxial cable
l _-_ 2-Way signal
I - splitter
onpage14 '_J I
-'{_1
CableTVBox
I =
VCR#1 : ;
LaSermc0d_er,Player.VCR,
VCR#2 I_ _ '-"_
I
IOo ooLOol
o_ IOl
StereoSystemAmplifier
Typicalfull feature setup. Follow connectionsthat pertainto your personal entertainment system.
16
EXTERNAL CONNECTIONS
CONNECTING EXTERNAL AUDIO AMPLIFIER
Tocontrol the audio level of an external audio amplifierwith the remote control, connect the system as shown below.
EXTERNAL
SPEAKERS
(REAROFTVSET)
AUDIOTO HI-FITERMINAL
TO AUDIO INPUT TERMINAL
OF
©
AUDIO AMPLIFIER
-'--_L
I
AUDIO
TO HI-FI
EXTERNAL
SPEAKERS
NOTE:
To prevent damage to the speaker and distorted sound, set the volume control of the audio amplifier lower and adjust
the sound using the remote controlof the TV set.
17
CONNECTING EXTERNAL VIDEO SOURCES
The exact arrangement you use toconnect the VCR, camcorder, laserdiscplayer to yourTV set isdependent on the modeland features
of each component. Check the owner's manual of each component for the location of video and audio inputs and outputs.
The followingconnectiondiagrams are offered as suggestions. However, you may need to modifythem toaccommodate your particular
assortment of components and features. For best performance, video and audio cables should be made from coaxial shielded wire.
Before Operating External Video Source
The inputmode ischanged every time the INPUT buttonispressed as shown below. Connect an extemal sourceto the INPUT terminal,
then press the INPUT button as necessary to view the input source. (See page 25.)
INPUT MODE SELECTION ORDER
(Antenna)
(Input)
VIDEO
NOTE:
I
When the TV is set to VIDEO and a video signal is not received from the VIDEO INPUT JACK on the jack panel ofthe J
TV (i.e., VCR/laserdisc player, etc. is not connected or the video device is OFF), the screen will be gray-blue.
I
CONNECTING A MONAURAL AUDIO VCR OR LASERDISC PLAYER
1. Connect the cable from the VIDEO OUT of the VCR or the laserdiscplayer to the INPUT (VIDEO) jack on the TV set below.
2. Connect the cable from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO) jack.
3. Pressthe INPUT buttonto view the program from the VCR or the laserdiscplayer. The VIDEO mode disappears automatically after
approximately eight seconds.
4. Press the INPUT button to return to the previous channel.
TV INPUT
TERMINAL
INPU'I
VIDEO
[lr_',\
\\_.JJl
IMONO_
AUDIO
=
VCR
VIDEOOUT AUDIOOUT
®1
18
CONNECTING EXTERNAL VIDEO SOURCES
CONNECTING A STEREO VCR OR STEREO LASERDISC PLAYER
1. Connect the cable from the VIDEO OUT of the VCR of the laserdisc player tothe INPUT (VIDEO) jack on the TV set below.
2. Connect the cable from the AUDIO OUT R of the VCR or the laserdiscplayer to the INPUT(AUDIO/R) jack.
3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player tothe INPUT(AUDIO/L) jack.
4. Press the INPUT button to view the program from the VCR or laserdisc player. The mode VIDEO disappears automatically after
approximately eight seconds.
5. Press the INPUT button to return to the previous channel.
INPUT11
VIDEO
O
(MONOI/oL
AUDIO
TV INPUT TERMINAL
000
S-VHS V L R
OUTPUT
BACKOF VCR
HITACHI MODEL
orsimilarmodel
NOTE:
Completely insertthe connection cord plugswhen connectingto rear panel jacks. The picturethat is played back willbe
abnormal if the connection is loose.
If you have an S-VHS VCR, use the S-INPUT cable in place of the standard video cable.
A single VCR can be used for VCR #1 and VCR #2, but notethat a VCR cannot record its own video or lineoutput.
(INPUT: 1 in example on pages 15 or 16.) Refer to your VCR operating guide for more information on line input-output
connections.
19
AUDIO SYSTEM SETUP
Match the numbers below to the diagrams for speaker placement and refer to the table for the different surroundsound requirements.
(See page 58 and 59 for SURROUND and SRS functions.)
0 The television's internal speakers.
(_ These speakers are connected to a separate audio amplifier. Use the =Audio to HI-FI" output on the television.
®
0
L '4"_
II
L J
3
l
®
0
L'-' .... " ' '__!'
I
LR
OUT IN
STEREOSYSTEM O
AMPUFIER
FOR 36FX48B AND 32FX48B
3 WAY SURROUND
FEATURE
OFF
MUSIC
MOVIE
SIMULATE
REQUIRED
CONNECTION
O
OPTIONAL
CONNECTION
0
EFFECT
Receive mono and stereo sound.
At stereo input, sound of music will be louder.
Surround channel added to left and right audio
amplifier speakers.
Movie theater reproduction, surround channel
added to left and right audio amplifier speakers.
At mono input, sound will be louder.
FOR 36UX58B
sns(e
FEATURE
ON
OFF
REQUIRED
CONNECTION
O
O
OPTIONAL
CONNECTION
@
EFFECT
Exciting and realistic 3D sound experience
from just two speakers. Sound Retrieval System.
Receive mono and stereo sound.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Hitachi 36FX48B Operating instructions

Category
LCD TVs
Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI