Hyperion Wireless Key Fob (4 button) www.wrensolutions.com 7L780 Rev A 200429
INSTALLATION GUIDE
HYPERION 4 BUTTON KEY FOB
HYP-FOB4-A
Hyperion Wireless Key Fob (4 button) www.wrensolutions.com 7L780 Rev A 200429
(800) 881-2249
PRODUCT SUPPORT
For comprehensive product support including manuals, FAQs and troubleshooting, visit our customer support portal.
WWW.WRENSOLUTIONS.COM
/HYPERION/HYPERION-SUPPORT
ABOUT THIS DOCUMENT
This document pertains to installation of the Hyperion 4-Button Key
Fob (HYP-FOB4-A). Before installation, please familiarize yourself with
this installation guide and review the Hyperion User Guide to
understand system configuration and setup.
PRODUCT MODIFICATIONS
This product is to be installed and used for the specific purpose for
which it was designed. It is not to be modified or serviced by anyone
other then Wren. Unauthorized changes or modifications to the
product will result in the warranty being voided and could possibly
invalidate regulatory certifications.
WARRANTY
Unless otherwise noted, all products are covered by Wren's Standard
Limited Manufacturer's Warranty as set forth in the current version of
Wren's Terms and Conditions
INTELLECTUAL PROPERTY RIGHTS
Wren maintains certain intellectual property rights that may pertain to
this product. To see a list of our patents, please refer to our
TRADEMARK ACKNOWLEDGMENTS
Wren®. the Wren logo, Hyperion® and the Hyperion logo are
trademarks of Wren. The trademarks that are followed by ® are
registered trademarks in the U.S. All other trademarks and/or
registered trademarks mentioned herein are properties of their
respective owners and are for reference purposes only. The use of
such third party trademarks does not indicate any affiliation with or
sponsorship of or by Wren. All rights reserved.
NOTICES
RF Exposure for FCC
WARNING: To satisfy FCC RF exposure requirements for mobile
transmitting devices, a separation distance of 31 cm or more should be
maintained between the antenna of this device and persons during
device operation. To ensure compliance, operations at closer than this
distance is not recommended. The antenna used for this transmitter
must not be co-located in conjunction with any other antenna or
transmitter.
RF Exposure for IC
WARNING: To satisfy IC RF exposure requirements for mobile
transmitting devices, a separation distance of 44 cm or more should be
maintained between the antenna of this device and persons during
device operation. To ensure compliance, operations at closer than this
distance is not recommended. The antenna used for this transmitter
must not be co-located in conjunction with any other antenna or
transmitter.
AVERTISSEMENT: Pour satisfaire IC RF exigences d’exposition pour
les appareils mobiles de transmission, une distance de séparation de 44
cm ou plus doit être maintenue entre l’antenne de cet appareil et des
personnes pendant le fonctionnement de l’appareil. Pour assurer la
conformité, les opérations au plus près que cette distance ne sont pas
recommandés. L’antenne utilisée pour cet émetteur ne doit pas être
situé en conjonction avec une autre antenne ou émetteur.
Hyperion Wireless Key Fob (4 button) www.wrensolutions.com 7L780 Rev A 200429
Prior to installation, verify that all hardware is included. If there
are missing components, please contact Wren.
COMPONENT LIST
Hyperion 4-button Key Fob
REQUIRED TOOLS AND ACCES-
#2 Phillips screw-
driver
AAA Batteries (x2)
INSTALL BATTERIES
1
Remove 4 screws from the back of the
enclosure to access the battery compartment.
Install the batteries making sure they are
installed in the proper orientation.
Reinstall the 4 enclosure screws, making sure
that the rubber seal is seated properly.
2
ADD DEVICE TO THE GATEWAY
The device is now powered on and ready to be added to Hyperion.
Refer to the Hyperion User Manual for setup details.
/
