9” Fan
MF222SL
Instruction book
Matsui MF222SL IB.qxd 27/11/06 12:25 PM Page 1
Getting to know your fan
Please read these instructions and have a good look at the
illustrations before using your fan.
Power cord
Rear guard
Oscillating pin
Front guard
On/off switch and
speed control
Matsui MF222SL IB.qxd 27/11/06 12:25 PM Page 2
Safety first !
Your fan should be used in such a way
that it is protected from moisture. e.g.
condensation, splashed water etc.
Stand your fan on a stable, level surface
during use.
Do not place or store your fan where it can
fall or be pulled into water or any other
liquid.
Do not reach for the appliance if it has
fallen in any water or any other liquid.
Unplug immediately.
It is DANGEROUS to insert fingers or
objects into the grill. Do not allow young
children to play with your fan.
Close supervision is necessary when your
fan is used near children.
No part of this publication may be reproduced,
stored in a retrieval system or transmitted, in any
form or by any means, without the prior
permission in writing of Dixons Stores Group, nor
be otherwise circulated in any form of binding or
cover other than that in which is published and
without asimilar condition including this condition
being imposed on the subsequent purchaser.
Your fan should be unplugged from
the wall socket when left unused for a
long time.
Your fan should be placed away from
heat sources such as radiators,
gas/electric fires and direct sunlight.
Keep the power cord away from any
heated surfaces.
Use the appliance only for its intended
use, as described in this manual.
Do not use outdoors.
Never use your fan if it is damaged in
any way.
Do not remove any fixed covers.
Never use this appliance if it is not
working properly, or if it has been
dropped or damaged.
Matsui MF222SL IB.qxd 27/11/06 12:25 PM Page 3
How to assemble your fan
1 2 3
Unscrew the GUARD LOCK
NUT.
Fit the REAR GUARD to the
MOTOR. Push firmly until the 3
pins stick through the 3 holes.
Secure the REAR GUARD to
the MOTOR using the GUARD
LOCK NUT.
Make sure
your fan is
unplugged
before you
attempt to
assemble
FRONT GUARD BLADE LOCATION PINS
GUARD LOCK NUT
During transit this component
is stored on the motor housing
MOTOR SHAFT
REAR GUARD
Matsui MF222SL IB.qxd 27/11/06 12:25 PM Page 4
4 5 6
Press the BLADE onto the
MOTOR SHAFT.
Insert the hook on the top of the
FRONT GUARD over the rim of
the REAR GUARD.
Secure the FRONT GUARD
using the 4 locking clips and the
2 screws.
Matsui MF222SL IB.qxd 27/11/06 12:25 PM Page 5
How to use your fan
Plug into a mains socket and
switch on at the wall.
Press buttons 1 or 2 to control
The fan speed. Press 0 to stop
the fan.
1 3
5
Adjust the angle of the fan.
2
To make the fan move from side
to side, push the OSCILLATING
PIN into the MOTOR.
4
To adjust the direction of the fan,
switch OFF. Pull the
OSCILLATING PIN up.
Matsui MF222SL IB.qxd 27/11/06 12:25 PM Page 6
Cleaning
Always unplug your fan from the mains supply before
attempting cleaning. Do not use harsh cleaners or
solvents on the fan as they may damage the casing.
Specifications
Power Supply..........230V 50Hz 30W
The fan blade and body of the unit should be cleaned
using a cloth dampened with warm water and detergent.
Make sure you do not allow water to seep into the
controls or motor housing of your fan.
This symbol on the product or in the instructions
means that your electrical and electronic equipment
should be disposed at the end of its life separately from
your household waste. There are separate collection
systems for recycling in the EU.
For more information, please contact the local authority
or your retailer where you purchased the product.
Matsui MF222SL IB.qxd 27/11/06 12:25 PM Page 7
Features and specifications are subject to change without notice.
All trademarks and registered trademarks are the property of their respective owners.
All rights reserved.
Matsui MF222SL IB.qxd 27/11/06 12:25 PM Page 8
/
