H3C s5800 series Installation guide

H3C S5800 Series Ethernet Switches

Installation Manual

New H3C Technologies Co., Ltd.

http://www.h3c.com.hk

Document version: 6W111-20170718

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of New H3C Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H

3

Care, , IRF, NetPilot, Netflow,

SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New

H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Environmental protection

This product has been designed to comply with the environmental protection requirements. The storage,

use, and disposal of this product must meet the applicable national laws and regulations.

Preface

H3C S5800 Series Ethernet Switches Installation Manual describes the appearance, installation,

power-on, maintenance, and troubleshooting of the H3C S5800 series Ethernet switches.

This preface includes the following topics about the documentation:

• Audience.

• Conventions.

• Obtaining documentation.

• Technical support

• Documentation feedback.

Audience

This documentation is intended for:

• Network planners.

• Field technical support and servicing engineers.

• Network administrators working with the S5800 series.

Conventions

The following information describes the conventions used in the documentation.

Command conventions

Convention Descri

p

tion

Boldface Bold text represents commands and keywords that you enter literally as shown.

Italic Italic text represents arguments that you replace with actual values.

[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars, from which

you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical bars, from

which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by vertical

bars, from which you select a minimum of one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by vertical

bars, from which you select one choice, multiple choices, or none.

&<1-n>

The argument or keyword and argument combination before the ampersand (&) sign can

be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Descri

p

tion

Boldface

Window names, button names, field names, and menu items are in Boldface. For

example, the New User window opens; click OK.

> Multi-level menus are separated by angle brackets. For example, File > Create > Folder.

Symbols

Convention Descri

p

tion

WARNING

An alert that calls attention to important information that if not understood or followed can

result in personal injury.

CAUTION

An alert that calls attention to important information that if not understood or followed can

result in data loss, data corruption, or damage to hardware or software.

IMPORTANT

An alert that calls attention to essential information.

NOTE

An alert that contains additional or supplementary information.

TIP

An alert that provides helpful information.

Network topology icons

Represents a generic network device, such as a router, switch, or firewall.

Represents a routing-capable device, such as a router or Layer 3 switch.

Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports

Layer 2 forwarding and other Layer 2 features.

Represents an access controller, a unified wired-WLAN module, or the access controller

engine on a unified wired-WLAN switch.

Represents an access point.

Wireless terminator unit.

Wireless terminator.

Represents a mesh access point.

Represents omnidirectional signals.

Represents directional signals.

T



Represents a security product, such as a firewall, UTM, multiservice security gateway, or

load balancing device.

Represents a security module, such as a firewall, load balancing, NetStream, SSL VPN,

IPS, or ACG module.

Examples provided in this document

Examples in this document might use devices that differ from your device in hardware model,

configuration, or software version. It is normal that the port numbers, sample output, screenshots, and

other information in the examples differ from what you have on your device.

Obtaining documentation

To access the most up-to-date H3C product documentation, go to the H3C website

at http://www.h3c.com.hk

.

To obtain information about installation, configuration, and maintenance, click

http://www.h3c.com.hk/Technical_Documents

To obtain software version information such as release notes, click

http://www.h3c.com.hk/Software_Download

Technical support

servic[email protected]

http://www.h3c.com.hk

Documentation feedback

You can email your comments about product documentation to info@h3c.com.

We appreciate your comments.



i

Contents

Product overview ·························································································································································· 1

About the H3C S5800 Switch Series ····························································································································· 1

Switch models and technical specifications ··················································································································· 1

Hardware compatibility matrix ········································································································································ 4

S5800-60C-PWR panel views ········································································································································· 6

Front panel ································································································································································ 6

Rear panel ································································································································································· 7

S5800-56C panel views ·················································································································································· 7

Front panel ································································································································································ 7

Rear panel ································································································································································· 9

S5800-56C-PWR panel views ········································································································································· 9

Front panel ································································································································································ 9

Rear panel ······························································································································································ 10

S5800-54S panel views ················································································································································ 10

Front panel ····························································································································································· 10

Rear panel ······························································································································································ 11

Left side panel ························································································································································ 11

S5800-32C panel views ··············································································································································· 12

Front panel ····························································································································································· 12

Rear panel ······························································································································································ 12

S5800-32C-PWR panel views ······································································································································ 13

Front panel ····························································································································································· 13

Rear panel ······························································································································································ 13

S5800-32F panel views ················································································································································ 14

Front panel ····························································································································································· 14

Rear panel ······························································································································································ 14

Ports ················································································································································································· 15

Console port ·························································································································································· 15

Management Ethernet port ··································································································································· 15

USB port ································································································································································· 15

10/100/1000Base-T Ethernet port ···················································································································· 16

100/1000Base-X SFP port ··································································································································· 16

SFP+ port ································································································································································ 17

LEDs ················································································································································································· 19

System status LED··················································································································································· 19

Power module LED ················································································································································· 20

RPS status LED ························································································································································ 20

Port mode LED ························································································································································ 21

Seven-segment LED ················································································································································ 21

10/100/1000Base-T Ethernet port LED ············································································································· 22

100/1000Base-X SFP port LED ··························································································································· 23

SFP+ port LED ························································································································································ 23

Management Ethernet port LEDs ·························································································································· 24

OAP card status LED ············································································································································· 24

PoE module status LED ·········································································································································· 24

Interface card status LED ······································································································································· 25

Hot swappable power modules···································································································································· 25

Hot swappable fan trays ··············································································································································· 27

Interface cards ································································································································································ 28

ii

OAP cards ······································································································································································ 29

Hot swappable PoE modules ········································································································································ 29

Preparing for installation ··········································································································································· 30

Safety recommendations ··············································································································································· 30

Examining the installation site ······································································································································ 30

Temperature/humidity ·········································································································································· 30

Cleanness ······························································································································································· 31

EMI ·········································································································································································· 31

Laser safety ····························································································································································· 31

Installation tools ······························································································································································ 32

Installing the switch ···················································································································································· 33

Installing the switch in a 19-inch rack ·························································································································· 34

Installation methods ··············································································································································· 34

Mounting bracket and cable management bracket kits ···················································································· 35

Rack mounting rail kit ··········································································································································· 36

Installing the mounting brackets, chassis rails, and grounding cable (for the S5800-54S) ·························· 36

Attaching the mounting brackets to the switch chassis (for all S5800 switches except the S5800-54S) ···· 39

Rack-mounting the S5800-54S switch ················································································································ 40

Rack-mounting an S5800 switch except the S5800-54S ················································································· 43

Mounting the switch on a workbench ·························································································································· 44

Grounding the switch ···················································································································································· 45

Grounding the switch with a grounding strip ····································································································· 45

Grounding the switch in other grounding environment ····················································································· 48

Installing/Removing a fan tray ····································································································································· 49

Installing a fan tray ··············································································································································· 49

Removing a fan tray ·············································································································································· 50

Installing/Removing a power module ·························································································································· 50

Installing/Removing a power module (for the S5800-54S) ············································································· 51

Installing/Removing a power module (for the S5800-60C-PWR and the S5800-32F) ································· 54

Connecting the power cord ·········································································································································· 56

Connecting an AC power cord to the switch ····································································································· 56

Connecting the switch to a –54 VDC output RPS ······························································································ 58

Connecting the switch to a 12 VDC output RPS ································································································ 58

Connecting the PSR150-A/PSR150-A1 ·············································································································· 59

Connecting the PSR150-D/PSR150-D1 to a –48 VDC power source ····························································· 60

Connecting the PSR150-D/PSR150-D1 to a –54 VDC output RPS ·································································· 61

Connecting the PSR300-12A/PSR300-12A1/PSR300-12A2 ·········································································· 61

Connecting the PSR300-12D1/PSR300-12D2 to a –48 VDC power source ················································ 62

Connecting the PSR300-12D1/PSR300-12D2 to a –54 VDC output RPS ······················································ 63

Connecting the PSR750-A ···································································································································· 63

Connecting the PSR750-D to a –54 VDC output RPS ························································································ 64

Connecting the LSVM1AC650/LSVM1AC300 ································································································· 65

Connecting the LSVM1DC650/LSVM1DC300 ································································································· 66

Installing/Removing an interface card························································································································· 66

Installing an interface card ··································································································································· 67

Removing an interface card ································································································································· 68

Installing/Removing an OAP card ······························································································································· 68

Installing an OAP card in the OAP card slot (only for the S5800-60C-PWR) ················································ 68

Removing the card in the OAP card slot (only for the S5800-60C-PWR) ······················································· 69

Installing an OAP card in an expansion interface card slot (for the entire series but the S5800-54S) ······· 70

Removing the OAP card in an expansion interface card slot (for the entire series but the S5800-54S) ···· 70

Installing/Removing a PoE module ······························································································································ 71

Installing a PoE module ········································································································································· 71

iii

Removing the PoE module ···································································································································· 71

Verifying the installation ················································································································································ 72

Powering on the switch for the first time ··················································································································· 73

Setting up the configuration environment ···················································································································· 73

Connecting the console cable ······································································································································ 73

Console cable ························································································································································ 73

Connection procedure ·········································································································································· 73

Setting terminal parameters ·········································································································································· 74

Powering on the switch·················································································································································· 77

Setting up an IRF fabric ············································································································································· 78

IRF fabric setup flowchart ·············································································································································· 78

Planning IRF fabric setup ··············································································································································· 79

Planning IRF fabric size and the installation site ································································································ 79

Identifying the master switch and planning IRF member IDs ············································································ 79

Planning IRF topology and connections ·············································································································· 80

Identifying physical IRF ports on the member switches ····················································································· 81

Planning the cabling scheme ······························································································································· 82

Configuring basic IRF settings ······································································································································· 84

Connecting the physical IRF ports ································································································································ 84

Accessing the IRF fabric to verify the configuration ··································································································· 85

Maintenance and troubleshooting ···························································································································· 86

Password loss ································································································································································· 86

Console login password loss ······························································································································· 86

Boot ROM password loss ····································································································································· 86

Power module failure ····················································································································································· 86

Fixed power module failure ································································································································· 86

Hot swappable power module failure ················································································································ 88

OAP card failure ···························································································································································· 89

Failure of the OAP card in the OAP card slot ···································································································· 89

Failure of the OAP card in an expansion interface card slot ··········································································· 90

Hot swappable PoE module failure ······························································································································ 90

Fan failure ······································································································································································· 91

Fixed fan failure ····················································································································································· 91

Hot swappable fan tray failure ···························································································································· 91

Configuration terminal problems ·································································································································· 91

Index ··········································································································································································· 93

1

Product overview

About the H3C S5800 Switch Series

The H3C S5800 Switch Series is a line of Layer 3 Gigabit Ethernet switching products intended for the

distribution and access layers of enterprise or metropolitan area networks. You can also use this switch

series to offer access to the server farms in a data center.

The H3C S5800 Switch Series offers the following benefits:

• 10-Gigabit uplinks and a wide range of features, including the routing features, IPv4 and IPv6 dual

stack, and H3C cluster management for streamlined network management.

• Innovative Intelligent Resilient Framework (IRF) technology, which can virtualize connected S5800

switches into one virtual switch for higher availability, scalability and resiliency, and manageability.

• Support for the H3C Open Application Architecture (OAA). You can install customized open

application platform (OAP) cards in your S5800 switch to provide services such as firewall,

anti-virus, IPS, and wireless access control.

Switch models and technical specifications

The H3C S5800 Switch Series includes the following models:

• S5800-60C-PWR

• S5800-56C

• S5800-56C-PWR

• S5800-54S

• S5800-32C

• S5800-32C-PWR

• S5800-32F

Table 1 H3C S5800 Switch Series technical specifications

Item

S5800-6

0C-PWR

S5800-56

C

S5800-5

6C-PWR

S5800-5

4S

S5800-3

2C

S5800-3

2C-PWR

S5800-3

2F

Dimensions

(H × W × D)

86.1 ×

440 ×

465 mm

(3.39 ×

17.32 ×

18.31 in)

43.6 ×

440 × 367

mm (1.72

× 17.32 ×

14.45 in)

43.6 ×

440 ×

427 mm

(1.72 ×

17.32 ×

16.81 in)

43.6 ×

440 ×

660 mm

(1.72 ×

17.32 ×

25.98 in)

43.6 ×

440 ×

367 mm

(1.72 ×

17.32 ×

14.45 in)

43.6 ×

440 ×

427 mm

(1.72 ×

17.32 ×

16.81 in)

43.6 ×

440 ×

427 mm

(1.72 ×

17.32 ×

16.81 in)

Weight

≤ 18 kg

(39.68 lb)

≤ 6.5 kg

(14.33 lb)

≤ 8.5 kg

(18.74 lb)

≤ 12.2 kg

(26.90 lb)

≤ 6.0 kg

(13.23 lb)

≤ 8 kg

(17.64 lb)

≤ 8.5 kg

(18.74 lb)

2

Item

S5800-6

0C-PWR

S5800-56

C

S5800-5

6C-PWR

S5800-5

4S

S5800-3

2C

S5800-3

2C-PWR

S5800-3

2F

Console ports

1, on the

front

panel

1, covered

by the logo

plate on

the front

panel

1, covered

by the

logo plate

on the

front panel

1, on the

rear panel

1, on the

front panel

1, on the

front panel

1, covered

by the

logo plate

on the

front panel

Management

Ethernet ports

N/A N/A N/A

1, on the

rear panel

N/A N/A

1, on the

rear panel

USB ports (full

speed)

1, on the

front

panel

1, covered

by the logo

plate on

the front

panel

1, covered

by the

logo plate

on the

front panel

1, on the

rear panel

1, on the

front panel

1, on the

front panel

1, covered

by the

logo plate

on the

front panel

10/100/10

00Base-T

Ethernet ports

48, PoE 48 48, PoE 48 24 24, PoE N/A

100/1000B

ase-X SFP

ports

4 N/A N/A N/A N/A N/A 24

SFP+ ports N/A

4 4 6 4 4 4

You can plug an SFP+ transceiver module, SFP transceiver module or SFP+ cable

into an SFP port. An SFP port plugged in with an SFP+ cable can be used to

connect IRF member switches.

Expansion

interface card

slots

2, on the

front

panel

1, on the

rear panel

1, on the

rear panel

N/A

1, on the

rear panel

1, on the

rear panel

1, on the

front panel

OAP card

slots

1 N/A N/A N/A N/A N/A N/A

Fan tray slots

1, hot

swapping

N/A

Fixed fans

are used.

N/A

Fixed fans

are used.

2, hot

swapping

N/A

Fixed fans

are used.

N/A

Fixed fans

are used

1, hot

swapping

PoE module

slots

1, N/A N/A N/A N/A N/A N/A

Power

module slots

2, hot

swapping

N/A N/A

2, hot

swapping

N/A N/A

2, hot

swapping

AC-input

voltage

Rated voltage: 100 VAC to 240 VAC @ 50 or 60 Hz

Max voltage: 90 VAC to 264 VAC @ 47 or 63 Hz

3

Item

S5800-6

0C-PWR

S5800-56

C

S5800-5

6C-PWR

S5800-5

4S

S5800-3

2C

S5800-3

2C-PWR

S5800-3

2F

DC-input

voltage

Rated

voltage:

• 300

W at

–48

VDC

to

–60

VDC

• 750

W at

–54

VDC

to

–57

VDC

N/A N/A

Rated

voltage:

–40 VDC

to –60

VDC

N/A N/A

Rated

voltage:

–48 VDC

to –60

VDC

RPS-input

voltage

Rated

voltage:

–52 VDC

to –55

VDC

Rated

voltage:

10.8 VDC

to 13.2

VDC

Rated

voltage:

–52 VDC

to –55

VDC

N/A

Rated

voltage:

10.8 VDC

to 13.2

VDC

Rated

voltage:

–52 VDC

to –55

VDC

Rated

voltage:

–52 VDC

to –55

VDC

Minimum

power

consumption

DC: 94 W

AC: 96 W

102 W

DC: 107

W

AC: 131

W

105 W 67 W

DC: 64 W

AC: 85 W

DC: 58 W

AC: 67 W

Maximum

power

consumption

Single DC

output:

1840 W

(1500 W

for PoE

output)

Dual DC

outputs:

1840 W

(1500 W

for PoE

output)

Single AC

output:

714 W

(425 W

for PoE

output)

Dual AC

outputs:

1147 W

(740 W

for PoE

output)

163 W

DC: 973

W (740

W for PoE

output)

AC: 673

W (370

W for PoE

output)

AC: 130

W

DC: 130

W

105 W

DC: 870

W (740

W for PoE

output)

AC: 598

W (370

W for PoE

output)

DC: 136

W

AC: 146

W

4

Item

S5800-6

0C-PWR

S5800-56

C

S5800-5

6C-PWR

S5800-5

4S

S5800-3

2C

S5800-3

2C-PWR

S5800-3

2F

Operating

temperature

0°C to 45°C (32°F to 113°F)

Operating

humidity

10% to 90%, noncondensing

Hardware compatibility matrix

Interface cards, OAP cards, PoE modules, power modules, and RPSs must be purchased separately.

When you purchase or install these components, check that they are compatible with the switch.

You must separately purchase two fan trays for the S5800-54S switch. All other S5800 switches come

with fixed fans or a fan tray installed.

Table 2 Pluggable component compatibility matrix

Card/module

S5800-6

0C-PWR

S5800-

56C

S5800-5

6C-PWR

S5800-5

4S

S5800-3

2C

S5800-3

2C-PWR

S5800-32F

Hot swa

pp

able

p

ower module o

p

tions

PSR300-12A Yes No No No No No No

PSR300-12A1 Yes No No No No No No

PSR300-12A2 Yes No No No No No No

PSR300-12D1 Yes No No No No No No

PSR300-12D2 Yes No No No No No No

PSR750-A Yes No No No No No No

PSR750-D Yes No No No No No No

PSR150-A No No No No No No Yes

PSR150-A1 No No No No No No Yes

PSR150-D No No No No No No Yes

PSR150-D1 No No No No No No Yes

LSVM1AC650 No No No Yes No No No

LSVM1DC650 No No No Yes No No No

LSVM1AC300 No No No Yes No No No

LSVM1DC300 No No No Yes No No No

Hot swa

pp

able fan tra

y

o

p

tions

LSW1FAN Yes No No No No No No

LSW1BFAN No No No No No No Yes

LSWM1FANSC No No No Yes No No No

LSWM1FANSCB No No No Yes No No No

5

Card/module

S5800-6

0C-PWR

S5800-

56C

S5800-5

6C-PWR

S5800-5

4S

S5800-3

2C

S5800-3

2C-PWR

S5800-32F

Interface card options

LSW1SP4P0

Yes Yes Yes No Yes Yes Yes

LSW1SP2P0

Yes Yes Yes No Yes Yes Yes

LSW1GP16P0

Yes Yes Yes No Yes Yes Yes

LSW1GT16P

Yes Yes Yes No Yes Yes Yes

LSW1XGT2P0 Yes Yes Yes No Yes Yes Yes

LSW1XGT4P0 Yes Yes Yes No Yes Yes Yes

OAP card options

LSWM1IPS10

Yes No No No No No No

LSWM1FW10

Yes No No No No No No

LSWM1WCM10

Yes No No No No No No

LSWM1WCM20

Yes Yes Yes No Yes Yes Yes

NOTE:

You install the LSWM1WCM20 card in the expansion interface card slot and all other OAP cards in the OAP

card slot.

Hot swappable PoE module options

LSW148POEM

Yes No No No No No No

NOTE:

For more information about these cards and modules, see the following sections:

• "Hot swappable power modules"

• "Hot swappable fan trays"

• "Interface cards"

• "OAP cards"

• "Hot swappable PoE modules"

Table 3 RPS compatibility matrix

RPS

S5800-

60C-PWR

S5800-

56C

S5800-

56C-PWR

S5800-

54S

S5800-

32C

S5800-

32C-PWR

S5800-

32F

RPS1000-A3 Yes No Yes No No Yes Yes

RPS1600-A Yes No Yes No No Yes Yes

RPS800-A No Yes No No Yes No Yes

6

S5800-60C-PWR panel views

Front panel

Figure 1 S5800-60C-PWR front panel

(1) Expansion interface card slot 1 (2) Expansion interface card slot 2

(3) 10/100/1000Base-T Ethernet port LED

(4) Seven-se

g

ment LED

(5) Port mode LED

(6) Console port

(7) USB port (8) System status LED (SYS)

(9) Power module 1 status LED (PWR1)

(10) Power module 2 status LED (PWR2)

(11) OAP card status LED (SLOT3) (12) PoE module status LED (SLOT4)

(13) 100/1000Base-X SFP port LED (14) Port LED mode switching button

(15) 100/1000Base-X SFP port (16) 10/100/1000Base-T auto-sensin

g

Ethernet port

NOTE:

• The S5800-60C-PWR switch comes with the two expansion interface card slots covered by filler panels.

In this figure, two LSW1SP4P0 interface cards are installed in the slots.

• You install the LSWM1WCM20 OAP card in an expansion interface card slot rather than the OAP card

slot.

7

Rear panel

Figure 2 S5800-60C-PWR rear panel

(1) OAP card slot

(2) PoE module slot

(3) Groundin

g

screw (4) Filler modules

(5) Power module slot 1 (6) Power module slot 2

(7) Hot swappable fan tray

NOTE:

• The S5800-60C-PWR switch comes with power module slot 1 empty and power module slot 2 covered

by a filler panel. You can install one or two power modules for the switch as needed. In this figure, two

PSR300-12A AC power modules are installed in the slots.

• This switch also comes with the PoE module slot and the OAP card slot covered by filler panels.

S5800-56C panel views

Front panel

Figure 3 S5800-56C front panel

(1) 10/100/1000Base-T auto-sensing Ethernet port (2) 10/100/1000Base-T Ethernet port LED

(3) Seven-se

g

ment LED (4) Port mode LED

(5) SFP+ port LED

(6) Lo

g

o plate (A console port and a USB port are under this lo

g

o plate)

(7) System status LED (SYS) (8) RPS status LED (RPS) (9) Interface card status LED (SLOT1)

(10) SFP+ port (11) Port LED mode switchin

g

button

8

To use the console port and USB port, open the logo plate.

Figure 4 Open the S5800-56C logo plate

CAUTION:

To avoid any damage to the logo plate, always follow these instructions on openin

g

and closin

g

the lo

g

o

plate:

• Insert your finger into the notch on the right side of the logo plate to open it. Do not try to open the lo

g

o

plate in any other ways.

• The logo plate is attached to the chassis with a rubber strip on its left. Rotate the logo plate within the

elasticity of the rubber strip. To avoid the rubber strip falling off or being broken, do not pull or rotate the

logo plate with excessive force.

• When closing the logo plate, insert the pin on the left of the logo plate into the fastening hole in the front

panel, rotate the logo plate inward until the tab on the right aligns with the fastening slot on the front

panel, and slightly press the logo plate until the tab clicks into the hole. If the tab is not fully engaged in

the fastening slot, make another try instead of pressing the logo plate with excessive force.

Figure 5 S5800-56C logo plate and ports under the logo plate

(1) Tab of the logo plate (2) Pin of the logo plate

(3) Console port (4) USB port

(5) Fastening slot on the front panel (6) Rubber strip

9

Rear panel

Figure 6 S5800-56C rear panel

(1) Bail latch (2) RPS DC-input power receptacle

(3) Groundin

g

screw (4) Expansion interface card slot

(5) AC-input power receptacle

NOTE:

The S5800-56C switch comes with the expansion interface card slot covered by a filler panel. In this

figure, an LSW1SP4P0 interface card is installed in the slot.

S5800-56C-PWR panel views

Front panel

Figure 7 S5800-56C-PWR front panel

(1) 10/100/1000Base-T auto-sensing Ethernet port (2) 10/100/1000Base-T Ethernet port LED

(3) Seven-se

g

ment LED (4) Port mode LED

(5) SFP+ port LED

(6) Lo

g

o plate (A console port and a USB port are under this lo

g

o plate)

(7) System status LED (SYS) (8) RPS status LED (RPS)

(9) Interface card status LED (SLOT1)

(10) SFP+ port

(11) Port LED mode switchin

g

button

To use the console port and USB port, open the logo plate, as shown in Figure 4 and Figure 5.

(1) (2)

(3)

(4) (5)

(6)

(7)

(8)

(9)

(11)

(10)

10

Rear panel

Figure 8 S5800-56C-PWR rear panel

(1) RPS DC-input power receptacle (2) Bail latch

(3) Groundin

g

screw (4) Interface card

slot

(5) AC-input power receptacle

NOTE:

The S5800-56C-PWR switch comes with the expansion interface card slot covered by a filler panel. In this

figure, an LSW1SP4P0 interface card is installed in the slot.

S5800-54S panel views

Front panel

Figure 9 S5800-54S front panel

(1) 10/100/1000Base-T auto-sensing Ethernet port (2) 10/100/1000Base-T Ethernet port LED

(3) SFP+ port (4) Seven-se

g

ment LED

(5) Port LED mode switchin

g

button (6) Port mode LED

(7) System status LED (SYS) (8) SFP+ port LED

11

Rear panel

Figure 10 S5800-54S rear panel

(1) Groundin

g

screw (auxiliary

g

roundin

g

point 2)

(2) Mana

g

ement Ethernet port

(3) Console port (4) Fan tray slot 1

(5) Fan tray slot 2

(6) Power module slot 1

(7) Power module slot 2 (8) LINK LED for the mana

g

ement Ethernet port

(9) ACT LED for the management Ethernet port (10) USB port

NOTE:

• The S5800-54S switch comes with the power module slots empty and the filler modules for the slots as

accessories. You can install one or two power modules for your S5800-54S switch as needed. In this

figure, two LSVM1AC650 AC power modules are installed.

• The S5800-54S switch comes with the fan tray slots empty. You must install two fan trays for the

S5800-54S for adequate heat dissipation, and their models must be the same. In this figure, two

LSWM1FANSC fan trays are installed.

Left side panel

Figure 11 S5800-54S left side panel

(1) Primary

g

roundin

g

point (2) Auxiliary

g

roundin

g

point 1

12

S5800-32C panel views

Front panel

Figure 12 S5800-32C front panel

(1) 10/100/1000Base-T auto-sensing Ethernet port (2) 10/100/1000Base-T Ethernet port LED

(3) SFP+ port LED

(4) Console port

(5) USB port (6) Seven-se

g

ment LED

(7) Port mode LED (8) System status LED (SYS)

(9) RPS status LED (RPS) (10) Interface card status LED (SLOT1)

(11) Port LED mode switchin

g

button

(12) SFP+ port

Rear panel

Figure 13 S5800-32C rear panel

(1) Bail latch (2) RPS DC-input power receptacle

(3) Groundin

g

screw (4) Interface card

slot

(5) AC-input power receptacle

NOTE:

• The S5800-32C switch comes with the expansion interface card slot covered by a filler panel. In this

figure, an LSW1SP4P0 interface card is installed in the slot.

• The switch also comes with the RPS DC-input power receptacle covered by a protective cover.

Page is loading ...

H3C s5800 series Installation guide

This manual is also suitable for

H3C s5800 series Installation guide

Related papers

Other documents