Furuno FCR-2119-BB User manual

Brand: Furuno

Model: FCR-2119-BB

Type: User manual

INSTRUCTION MANUAL

SETTING AND ADJUSTMENTS

www.furuno.com

All brand and product names are trademarks, registered trademarks or service marks of their respective holders.

Model FMD-3200/FMD-3200-BB/FMD-3300/FCR-2119-BB/

FCR-2129-BB/FCR-2139S-BB/FCR-2819/FCR-2829

FCR-2839S/FCR-2829W/FCR-2839SW

This manual is solely for use by the installer. Under no

circumstances shall this manual be released to the user.

The installer shall remove this manual from the vessel

after installation.

This manual contains no password data. Obtain password

data from FURUNO before beginning the installation.

Pub. No. E42-01204-N

(1907, YOSH) FMD-3xxx/FCR-2xx9

Printed in Japan

www.furuno.com

00019485812

INTRODUCTION

About this manual

This manual shows how to setup ECDIS and Chart Radar after the installation.

After setting, make a backup copy of configuration data onto a medium (PC, etc.).

Preparation

• PC (for the LAN connection)

• LAN cable (for the LAN connection)

Trademarks

Windows and Internet Explorer are either registered trademarks or trademarks of Microsoft Cor-

poration in the United States and/or other countries.

Silent mode

Use the silent mode when the ECDIS is not required, like in a harbor. This mode deactivates the

audio alarms.

1. Click the [OTHERS] button on the Status bar in the chart mode then click [SILENT].

You are prompted for a password.

2. Enter "3000", then click the [OK] button.

The following pop-up window appears.

3. To return to normal operation, click the [Back to Normal Mode] button in the pop-up window

shown above.

Click to return to normal operation.

TABLE OF CONTENTS

1. INITIAL SETTING AND ADJUSTMENT ................................................................1-1

1.1 How to Access the [Common Installation Setting] Menu ...........................................1-1

1.1.1 Laptop PC (LAN connection) access ............................................................. 1-1

1.1.2 Control Unit RCU-024/025/026 ...................................................................... 1-2

1.1.3 [Common Installation Setting] menu contents................................................ 1-3

1.2 [Basic Setting] Menu .................................................................................................. 1-4

1.2.1 [Basic Setting] window ................................................................................... 1-4

1.2.2 [Peripherals] window...................................................................................... 1-6

1.2.3 [VDR] window................................................................................................. 1-9

1.2.4 [Route Transfer] window .............................................................................. 1-10

1.2.5 [Application] window..................................................................................... 1-10

1.2.6 [Ship Name] window .................................................................................... 1-11

1.2.7 [ECDIS/Radar] window ................................................................................ 1-11

1.2.8 [Language] window ...................................................................................... 1-12

1.3 [Own Ship Setting] Menu ......................................................................................... 1-13

1.4 [Installation Parameters] Menu ................................................................................ 1-15

1.4.1 Sensor setting .............................................................................................. 1-15

1.4.2 Processor unit configuration......................................................................... 1-17

1.4.3 Activating the connection with the processor unit of the FAR-28 series

radar (ECDIS only).......................................................................................1-24

1.4.4 Sensor Adapter configuration....................................................................... 1-26

1.4.5 Antenna unit configuration ........................................................................... 1-30

1.4.6 Radar connection box configuration (ECDIS only)....................................... 1-31

1.4.7 Monitoring of HUB........................................................................................ 1-32

1.4.8 Signal and Port setting for external equipment ............................................ 1-33

1.4.9 Customized sensor setting........................................................................... 1-35

1.4.10 Settings to activate the shuttle ferry mode (Chart Radar only) .................... 1-36

1.5 [CCRS] Menu ........................................................................................................... 1-37

1.5.1 How to select the [Data Source]................................................................... 1-37

1.5.2 How to set [Transmission Group]................................................................. 1-38

1.5.3 [CCRS Setting] window................................................................................ 1-40

1.6 [TCS] Menu .............................................................................................................. 1-41

1.6.1 Preparation................................................................................................... 1-41

1.6.2 How to set the TCS for autopilot .................................................................. 1-43

1.6.3 How to set the Navigation Parameter .......................................................... 1-45

1.6.4 Multiple ECDIS and autopilot control ........................................................... 1-50

1.6.5 Detail settings for the TCS ........................................................................... 1-51

1.6.6 [Filter Setting] window.................................................................................. 1-53

1.6.7 [Other Setting] window................................................................................. 1-53

1.7 [AMS] Menu ............................................................................................................. 1-54

1.7.1 AMS mode operation ................................................................................... 1-54

1.7.2 Master/Backup AMS setting......................................................................... 1-55

1.7.3 Alert transfer setting..................................................................................... 1-56

1.7.4 Other setting window.................................................................................... 1-58

1.7.5 How to import and export [AMS] menu settings........................................... 1-59

1.8 [Alert Define List] Menu............................................................................................ 1-60

1.8.1 Alert Group Setting....................................................................................... 1-60

1.8.2 How to add an alert group............................................................................1-62

1.8.3 How to edit an alert group............................................................................ 1-63

1.8.4 How to delete an alert group........................................................................ 1-63

1.8.5 Alert Definition setting for each equipment .................................................. 1-63

1.8.6 How to add an alert definition....................................................................... 1-65

TABLE OF CONTENTS

iii

1.8.7 How to edit an alert definition .......................................................................1-67

1.8.8 How to delete an alert definition ...................................................................1-67

1.9 [Data Sharing] Menu.................................................................................................1-67

1.10 [Save and Sync] Menu .............................................................................................1-68

1.10.1 Consistency check and save the configuration ............................................1-68

1.10.2 How to save the configuration data to a medium .........................................1-70

1.10.3 How to load the configuration data ..............................................................1-70

1.11 [System Monitor] Menu.............................................................................................1-71

1.12 [Software Update] Menu...........................................................................................1-72

1.13 [Factory Test & Default] Menu..................................................................................1-73

1.14 [Conning] Menu ........................................................................................................1-74

1.14.1 How to select the data source ......................................................................1-76

1.14.2 Advanced settings window ...........................................................................1-77

1.15 Network Transmission Setting Between ECDIS and Radar.....................................1-98

1.16 How to Set the Forwarding Distance......................................................................1-101

1.17 Synchronization With Ship’s Clock.........................................................................1-102

1.18 How to Change the Color of Data in the Sensor Information Box According to

Integrity...................................................................................................................1-102

2. SETTING FOR SENSOR ADAPTER.....................................................................2-1

2.1 How to Set the Equipment ID .....................................................................................2-1

2.2 How to Save the Log File ...........................................................................................2-2

2.3 How to Update the Firmware (MC-3000S) .................................................................2-2

2.3.1 How to activate the maintenance program.....................................................2-3

2.3.2 How to confirm the firmware program version................................................2-3

2.3.3 How to update the firmware program .............................................................2-4

3. DUAL GYRO SYSTEM (ECDIS Only)...................................................................3-1

4. HUB-3000 IGMP QUERIER SETTING ..................................................................4-1

5. RAYTHEON ANSCHUTZ AUTOPILOT NP-5400.................................................5-1

5.1 Installation Parameters...............................................................................................5-1

5.1.1 HCS setting ....................................................................................................5-1

5.1.2 NP-5400 alert and backup navigator setting ..................................................5-2

5.1.3 BNWAS setting...............................................................................................5-2

5.1.4 Serial ports configuration................................................................................5-3

5.2 TCS Port Setting.........................................................................................................5-4

5.3 NP-5400 Alert Port Setting .........................................................................................5-5

5.4 NP-5400 Backup Navigator Port Setting ....................................................................5-5

5.5 Position and Time Ports Settings ...............................................................................5-5

5.6 Speed Port Setting .....................................................................................................5-6

5.7 Backup Navigator Setting...........................................................................................5-6

5.8 Save and Sync ...........................................................................................................5-6

APPENDIX 1 EQUIPMENT ID List...........................................................................AP-1

APPENDIX 2 SUBSYSTEM......................................................................................AP-3

APPENDIX 3 RCB-002 IP ADDRESS SETTING......................................................AP-4

TABLE OF CONTENTS

This page is intentionally left blank.

1-1

1. INITIAL SETTING AND

ADJUSTMENT

This chapter shows you how to enter the initial settings for the processor unit (EC-

3000) of ECDIS and Chart Radar after the installation.

Note: Each unit has a default IP address. Enter the initial settings (Equipment ID set-

ting) and change the IP address on the [Basic Setting] menu (see section 1.2.), before

connecting each unit and building the network. After entering the equipment ID(s),

build the network and enter other settings. You can enter the settings of each unit all

at one time by building the network.

1.1 How to Access the [Common Installation

Setting] Menu

The initial settings for the ECDIS and Chart Radar are performed on the [Common In-

stallation Setting] menu. The [Common Installation Setting] menu works with a web

browser.

Access the [Common Installation Setting] menu by either of the two methods shown

below.

• Access on a laptop PC (LAN connection). See section 1.1.1.

• Access with the control unit RCU-024/025/026. See section 1.1.2.

Note 1: Supported browsers are as follows:

• Internet Explorer

• Firefox ESR 60

Note 2: To update the software with the updating file (see section 1.12.), access the

[Common Installation Setting] menu via LAN connection. To update the software with

the DVD, access the [Common Installation Setting] menu with the control unit.

Note 3: When you access the MC-3000S directly from Internet Explorer

, you cannot

adjust the settings on the [Alert Define List] menu. Access either the EC-3000, or use

Firefox to adjust the settings on the [Alert Define List] menu.

1.1.1 Laptop PC (LAN connection) access

1. Set the IP address and subnet mask of the PC according to the LAN port where

the PC is connected.

Note: For the Sensor Adapter, use the LAN2 port (sensor network).

LAN port

IP address/

Subnet mask

Setting value

LAN1

(Gateway network)

IP address 192.168.31.200

Subnet mask 255.255.255.0

LAN2

(Sensor network)

IP address 172.31.16.200

Subnet mask 255.255.0.0

1. INITIAL SETTING AND ADJUSTMENT

1-2

2. Connect the PC to the LAN1 or LAN2 port of the processor unit with a LAN cable.

Note: It is possible to connect to the LAN1 or LAN2 port via a LAN hub. However,

to operate from the [Basic Setting] menu, turn off all units except the unit to be set.

Enter settings to processor units one by one.

3. Activate the web browser on the PC.

4. Enter the IP address on the address bar on the browser referring to the following

table.

When entering the IP address on the address bar, you are asked to enter ID and

password.

5. Enter the ID and password correctly then click the [Login] button.

The [Common Installation Setting] menu appears.

1.1.2 Control Unit RCU-024/025/026

1. Click [ ] on the status bar then select [Settings]. The pop-up message shown

below appears.

2. Click [OK] to show the [Settings] menu.

3. Click [SERVICE MODE] on the status bar, and then select [Service Login].

The password input dialog box appears.

Access

point

Type IP address

For the initial setting Gateway

Network

ECDIS 192.168.31.1

Chart Radar 192.168.31.31

Sensor

Network

ECDIS 172.31.16.1

Chart Radar 172.31.16.21

For re-setting the unit Gateway

Network

ECDIS

Chart Radar

Enter the IP address of the gateway

or sensor network according to the

Equipment ID used in the system.

See the Equipment ID list at the back

of this manual.

1. INITIAL SETTING AND ADJUSTMENT

1-3

4. Enter the password and click [OK]. [Service Mode] is shown at the bottom left po-

sition of the [Settings] window.

For RCU-024: Use the keyboard on the control unit to enter the password.

For RCU-025/026: Use the software keyboard on the display to enter the pass-

word.

5. Click [SERVICE MODE] on the status bar, and then select [Common Installation

Setting]. The message shown below appears.

6. Click [OK] to activate the web browser and show the dialog box asking for ID and

password.

7. Enter the ID and password correctly then click the [Login] button.

The [Common Installation Setting] menu appears.

1.1.3 [Common Installation Setting] menu contents

Note: Click [Exit] to close and logout from the [Common Installation Setting] menu.

You can close and logout by clicking on the web browser. However the menu can

not be re-accessed for a while.

The selected tab is highlighted in blue on the tab bar. The view area and menu bar

change according to the tab selected.

Click [ (or )] at the tab bar to shift the tab to the left (or right).

Note: If the tab bar does not move when clicking either or , clear the browser

cache.

Tab bar

View area

Info bar

Menu bar*

Click here to close and

logout from the

[Common Installation

Setting] menu.

*: Selected item is highlighted in blue.

1. INITIAL SETTING AND ADJUSTMENT

1-4

*: Adjustment not required.

1.2 [Basic Setting] Menu

1.2.1 [Basic Setting] window

1. Access the [Common Installation Setting] menu and click [Basic Setting] on the

tab bar.

2. Select the Equipment ID of the processor unit from the [Equipment ID] pull-down

list.

For the ECDIS: Setting range: [ECD001] to [ECD016]

Tab name Feature

Basic Setting Sets the Equipment ID, monitor unit, printer, and own ship

information, etc.

Own Ship Setting Enters the ship’s parameter and sensor position.

Installation Parameters Sets the system configuration and input/output data.

CCRS Sets the priority of the sensors and NMEA sentences.

TCS Sets the TCS.

AMS Sets the AMS and relevant settings.

Alert Define List Sets the alerts.

Data Sharing* Sets the interlocking system between units.

Save and Sync Save and synchronize the settings. You can save settings to

a medium.

System Monitor Confirms the system condition.

Software Update Updates the software.

Factory Test and Default Performs the factory test; restores the default settings.

Conning Configures the layout and data to show on the conning dis-

play.

Click . .

TCSTCS AMSAMSCCRSCCRS

Basic SettingBasic Setting

Own Ship SettingOwn Ship Setting Installation ParametersInstallation Parameters

TCSTCS AMSAMSCCRSCCRSOwn Ship SettingOwn Ship Setting Installation ParametersInstallation Parameters Alert Define ListAlert Define List

1. INITIAL SETTING AND ADJUSTMENT

1-5

For the Chart Radar: Setting range: [CRA001] to [CRA004]. Do not select

[CRA005] to [CRA010].

The [Equipment Name], [Equipment Type No.], and [IP Address] are automatically

entered according to the Equipment ID. For details, see the Equipment ID list is at

the back of this manual.

Note 1: For the first ECDIS, set [Equipment ID] to [ECD001]. For the first Chart

Radar, set [Equipment ID] to [CRA001].

Note 2: Assign a different Equipment ID to each processor unit.

Note 3: [Serial No.] is entered before shipment. If you change the SSD or delete

[Serial No.] by mistake, click the box of [Serial No.] to enter the serial number of

the processor unit (example: xxxx-xxxx).

Note 4: The properties of data transmitted under IEC61162-450 protocol are

changed according to the Equipment ID settings.

• The Processor Unit's SFID, Device No. and Channel change as shown in the

following table.

• When this unit has Back-up ECDIS enabled (see subsection 1.4.2) and Back-

up ECDIS mode is active, the SFID changes as shown below.

*: This SFID is applied to all ECDIS-related functions.

3. Select [FMD-3200|3300] or [FCR-29] from the [Equipment Type No.] pull-down

list.

Note: Do not use [FCR-29 ED.1] and [FCR-29 ED.2].

Equipment ID SFID Device No. Channel

CRA001 RA0001 61 1, 2, 3

CRA002 RA0002 62 1, 2, 3

CRA003 RA0003 63 1, 2, 3

CRA004 RA0004 64 1, 2, 3

ECD001 EI0001 21 1, 2, 3

ECD002 EI0002 22 1, 2, 3

ECD003 EI0003 23 1, 2, 3

ECD004 EI0004 24 1, 2, 3

ECD005 EI0005 25 1, 2, 3

ECD006 EI0006 26 1, 2, 3

ECD007 EI0007 27 1, 2, 3

ECD008 EI0008 28 1, 2, 3

ECD009 EI0009 29 1, 2, 3

ECD010 EI0010 30 1, 2, 3

ECD011 EI0011 31 1, 2, 3

ECD012 EI0012 32 1, 2, 3

ECD013 EI0013 33 1, 2, 3

ECD014 EI0014 34 1, 2, 3

ECD015 EI0015 35 1, 2, 3

ECD016 EI0016 36 1, 2, 3

Back-up ECDIS

is not active

Back-up ECDIS

is active*

RA0001 EI0021

RA0002 EI0022

RA0003 EI0023

RA0004 EI0024

1. INITIAL SETTING AND ADJUSTMENT

1-6

4. For the Chart Radar, select the Equipment ID of the radar processor unit from

the [Equipment ID] pull-down list. Setting range: [RAS001] to [RAS004]. Do not

use [RAS005] to [RAS010]. For the ECDIS, go to step 8.

The [Equipment Name], [Equipment Type No.], and [IP Address] are automatically

entered according to the Equipment ID.

5. Select [RPU-013] from the [Equipment Type No.] pull-down list.

6. Select the antenna position from the [Antenna Position] pull-down list.

Settings: [Fore], [Main Top], [Main 2nd], [Main 3rd], [Aft], [Port], [Starboard].

7. Click the box of [Serial No.] to enter the serial number of the radar processor unit

(example: xxxx-xxxx).

8. Click [Save] on the info bar. Several confirmation messages appear. Click [OK] to

reboot the system. To discard all changes, click [Discard Changes].

1.2.2 [Peripherals] window

1. Access the [Common Installation Setting] menu and click [Basic Setting] on the

tab bar.

2. Click [Peripherals] on the menu bar.

3. Select the monitor type and resolution connected to the DVI1 port from the [Type

Number] pull-down list of DVI1.

The setting options are as follows:

• [MU-190 (SXGA)] • [HD 24T22FUD (WUXGA)]

• [MU-231 (SXGA)] • [HD 26T21MMD (WUXGA)]

• [MU-231 (UXGA)]

• [HD 26T22MMD (WUXGA)]*

• [MU-270W (WUXGA)]*

• [HD 26T22FUD (WUXGA)]

• [MU-270W-B (WUXGA)]*

• [HD 27T22FUD (FHD)]*

• [MU-201CE (SXGA)] • [HD 27T22FUD (WUXGA)]

• [MU-231CE (SXGA)]

• [HD 32T22FUD (FHD)]*

• [MU-231CE (UXGA)]*

• [HD 32T22FUD (WUXGA)]

• [JH 19T14FUD (SXGA)]

• [HD 55T22FUD (FHD)]*

䠖Not used.

䠖Shown for the ECDIS.

䠖Shown when [Connected] is selected in [Connection] of [Service Gateway].

1. INITIAL SETTING AND ADJUSTMENT

1-7

Note 1: The DVI2 port outputs the display data same as the data of DVI1 port.

Note 2: If the MU-201, MU-231CE or the monitor of Hatteland Display is connect-

ed, the optional cable DSUB9P-X2-A-L5M/L10M for brilliance control is required

to connect.

4. Select the monitor type and resolution connected to the DVI3 port from the [Type

Number] pull-down list of DVI3.

When the processor unit is not connected to the VDR or you do not use the dual

display, select [Not Connected (NONE)] and go to the step 8.

5. Select the display data to output from the DVI3 port from the [Output Mode] pull-

down list.

6. When one of the following monitors is selected at step 3, click the [Run] button for

[Monitor Color Calibration] to perform the color calibration. For all other monitors,

go to step 8.

“Processing” appears at the next to the [Run] button during the color calibration.

After completing the calibration, check result appears ([Succeeded] or [Failed]).

• [JH 20T17FUD (UXGA)] • [HD 55T22FUD (WUXGA)]

• [JH 23T12FUD (UXGA)]*

• [NI WA460-01.MON.01(FHD)]*

• [JH 23T14FUD (UXGA)] • [NI WA460-01.MON.01(WUXGA)]

• [JH 26T11MMD (WUXGA)]*

• [NI WA270-01.MON.01-XXFU(FHD)]*

• [HD 19T21MMD (SXGA)]*

• [NI WA270-01.MON.01-XXFU(WUXGA)]

• [HD 24T21MMD (FHD)]*

• [AHD 119F (SXGA)]*

• [HD 24T21MMD (WUXGA)]*

• [AHD 119G (SXGA)]*

• [HD 24T22FUD (FHD)]*

: When the serial number of the MU-270W is “1000-4610-” or “10”, se-

lect [MU-270W (WUXGA)]. If not, select [MU-270W-B (WUXGA)].

: Do not use for the monitor connected to the DVI1 port. These monitors are avail-

able for the port other than DVI1 port.

: Not used.

: ECDIS only.

Setting option Remarks

[Clone] DVI1 to DVI3 ports output the same resolution and display data. For the

ECDIS, the DVI1 port can switch ECDIS and Conning display data.

Note 1: When [Clone] is selected, the [Type Number] for DVI1 and

DVI3 port should be same setting option.

Note 2: When the Chart Radar is connected to a VDR, it is required to

set to [Clone].

[Independent] The DVI3 port outputs the conning display data.

Note: Do not set to [Independent] in case of the Chart Radar, when the

CPU board of the EC-3000 is “ADP-555-xx”.

• [HD 19T21MMD (SXGA)] • [HD 26T22FUD (WUXGA)]

• [HD 24T21MMD (FHD)] • [HD 27T22FUD (FHD)]

• [HD 24T21MMD (WUXGA)] • [HD 27T22FUD (WUXGA)]

• [HD 24T22FUD (FHD)] • [HD 32T22FUD (FHD)]

• [HD 24T22FUD (WUXGA)] • [HD 32T22FUD (WUXGA)]

• [HD 26T21MMD (WUXGA)] • [HD 55T22FUD (FHD)]

• [HD 26T22MMD (WUXGA)] • [HD 55T22FUD (WUXGA)]

1. INITIAL SETTING AND ADJUSTMENT

1-8

When the check result is [Succeeded], the following confirmation message ap-

pears. Click the [OK] button to reboot the system and apply the calibration setting.

When the check result is [Failed], retry the color calibration. If the error is not rec-

tified, contact your dealer.

Note: Be sure to perform the color calibration. If the calibration is not performed,

you cannot adjust the monitor brilliance.

7. Access the [Common Installation Setting] menu and open the [Peripherals] win-

dow again.

8. Select the type of the printer from the [Printer Mode] pull-down list.

Note 1: For no printer, set [Printer Mode] to [HP Officejet 100 Mobile].

Note 2: The printer HP Officejet Pro 8000 Enterprise Printer can not be connected

to the processor unit.

9. Select the port that connects the printer from the [Printer Port] pull-down list.

USB: Only the processor unit connected to the printer can print.

Network: EC-3000s in the same network can print. The IP address of the printer

is shown on the [Printer] screen. Do not change the IP address.

10. To automatically print images captured with [Screenshot] function, check the

checkbox for [Auto Print out (SS)].

11. For the ECDIS, select the chart data storage equipment from the [Connection]

pull-down list in the [Chart Service] field. In this case, the IP address appears be-

low the [Connection] item. For the Chart Radar, the [Chart Service] field does not

appear. Go to the next step.

• [Not Connected]: Not connected to chart data storage equipment.

• [FURUNO]: Connected to the FURUNO Gate-1.

• [NAVTOR]: Connected to the NAVTOR NavBox.

• [NeCST]: Not used.

Setting option Remarks

[HP Officejet Pro 8000] Connect the printer to LAN1 port or USB port, and then set

the IP address of the printer to "192.168.31.241". For how to

set the IP address of the printer, see the operator’s manual

of the printer.

[HP Officejet Pro 8100]

[HP Officejet Pro 8210]

[HP Officejet 100 Mobile] Connect the printer to the USB port of the processor unit.

[HP Officejet 200 Mobile]

Printer Printer Port

HP Officejet 100 Mobile/HP Officejet 200 Mobile/

Not Connected

[USB]

HP Officejet Pro 8000/HP Officejet Pro 8100/

HP Officejet Pro 8210

[USB], [Network]

1. INITIAL SETTING AND ADJUSTMENT

1-9

12. To connect a service gateway, select [Connected] at [Service Gateway] then the

IP address and the port number appear below the [Connected] item. Do not

change these settings.

13. Click [Save] on the info bar. Several confirmation messages appear. Click [OK] to

reboot the system. To discard all changes, click [Discard Changes].

Note 1: If the monitor does not display images correctly after system reboot, re-

boot the monitor.

Note 2: When the message shown below appears after system reboot, confirm

the connection and settings of the system.

1.2.3 [VDR] window

1. Access the [Common Installation Setting] menu and click [Basic Setting] on the

tab bar.

2. Click [VDR] on the menu bar.

3. If a VDR is connected, select [Connected] from the [Connection] pull-down list.

Refer to the table below to set the items in the menu.

Menu item/

interactive field

Description

[Monitor] Select the DVI port connected with the VDR.

[Transmit per 15 sec.] Set the number of transmissions in 15 seconds.

[Transmission Rate] Set the transmitting rate.

[Image Format] Set the image format.

[JPEG Quality] Set the quality of JPEG data. Available when [JPEG] is se-

lected for [Image Format].

[Network] Select the network connected with the VDR.

[Transmission Timing] Set the delay timing. The delay is applied regardless of the

Display Mode selected (RADAR or Back-up ECDIS).

[Destination] Set the IP address and port of the destination.

1. INITIAL SETTING AND ADJUSTMENT

1-10

4. Click [Save] on the info bar. Several confirmation messages appear. Click [OK] to

reboot the system. To discard all changes, click [Discard Changes].

1.2.4 [Route Transfer] window

1. Access the [Common Installation Setting] menu and click [Basic Setting] on the

tab bar.

2. Click [Route Transfer] on the menu bar.

3. To transfer data to a specified network, select [Connected] from the [Connection]

pull-down list.

4. Click [Save] on the info bar. Several confirmation messages appear. Click [OK] to

reboot the system. To discard all changes, click [Discard Changes].

1.2.5 [Application] window

1. Access the [Common Installation Setting] menu and click [Basic Setting] on the

tab bar.

2. Click [Application] on the menu bar.

[Source] Set the status and information text, max. 16 characters.

[Location] Set the status and information text, max. 32 characters.

[Initial Value of Se-

quence No.]

Set the initial value for the binary transmission sequence

number (IEC61162-450 compliant) to be used when

transmitting video to a VDR.

Menu item Description

[Connection] Select [Connected] to transfer the data.

[Transmission Rate] Set the transmission rate.

[Network] Select the destination network for route data.

[Destination] Set the IP address and port of the destination.

[Initial Value of Sequence

No.]

Set the initial value for the binary transmission se-

quence number (IEC61162-450 compliant) to be

used when transferring route data to a device(s)

connected to the LAN.

Menu item/

interactive field

Description

1. INITIAL SETTING AND ADJUSTMENT

1-11

3. Select the primary display mode from the [Primary] pull-down list.

The primary display mode is displayed when you start the ECDIS. Also, the work-

ing indicator at the upper right changes according to the setting, and the spinner

can be clicked to return to the primary display mode.

Note: [AMS] is not available for Chart Radar systems.

4. Click [Save] on the info bar. Several confirmation messages appear. Click [OK] to

reboot the system. To discard all changes, click [Discard Changes].

1.2.6 [Ship Name] window

1. Access the [Common Installation Setting] menu and click [Basic Setting] on the

tab bar.

2. Click [Ship Name] on the menu bar.

3. Enter your ship information. The data entered here is included in any printing.

Note: ECDIS and Chart Radar can display own ship’s data input from AIS, on the

[Own Ship] page in the [Nav Status] menu. The data entered here is not reflected

to the AIS data.

4. Click [Save] on the info bar. Several confirmation messages appear. Click [OK] to

reboot the system. To discard all changes, click [Discard Changes].

1.2.7 [ECDIS/Radar] window

[Ship Name]: Own ship’s name. [Call Sign]: Own ship’s call sign

[IMO No.]: Own ship’s IMO no. [MMSI]: Own ship’s ID

Menu item Description

[Calculate CPA/TCPA] Keep the default setting. Confirm that the checkbox has no check

mark. If there is a check mark, remove it.

: No setting.

: [ECDIS] is selected.

: [RADAR] is selected.

: [CONNING] is selected.

: [AMS] is selected.

1. INITIAL SETTING AND ADJUSTMENT

1-12

1.2.8 [Language] window

The menu language for the everyday operating screens can be set to English or Jap-

anese. The [Common Installation Setting] menu has English menus only.

Note: This language setting is synchronized with all processor units on the network.

Reboot the synchronized processor unit(s) to use the selected menu language.

1. Access the [Common Installation Setting] menu and click [Basic Setting] on the

tab bar.

2. Click [Language] on the menu bar.

3. Select [English] (default) or [Japanese].

4. Click [Save] on the info bar. Several confirmation messages appear. Click [OK] to

reboot the system. To discard all changes, click [Discard Changes].

[Use Legacy TTM ID] For ECDIS:

Determine the behavior when the TTM sentence contains a “0”

(zero). Refer to the table below and set according to the maker of

radar and the TTM ID range.

Note 1: N/A means that the setting does not affect the operation

of FMD.

Note 2: When you connect the FURUNO radar, it is recommend-

ed to check the checkbox.

For Chart Radar:

When the checkbox is checked, the TT whose ID is “100” is out-

put with the ID “0”. This checkbox is used only when needed. For

example, the checkbox may be checked when a non-Furuno EC-

DIS is connected.

[RAMDISK Size (ADP-

555-xx)]

• [1GB (ECDIS)]: Select when the radar function is not used.

• [2GB (Radar/MFD)]: Select when the radar function is used.

Note: This menu item appears only when the CPU board of the

EC-3000 is “ADP-555-xx”. Also, this menu item is not shown for

FCR-29.

Menu item Description

Radar

maker

TTM ID

range

Recommended

setting

FURUNO

Other maker

00-99

01-200

00-99

01-99

00-999

01-999

Checked

N/A

Checked

N/A

Not checked

N/A

1. INITIAL SETTING AND ADJUSTMENT

1-13

1.3 [Own Ship Setting] Menu

Enter the information for ship parameters/CCRP, antenna unit, GPS sensor, AIS tran-

sponder, echo sounder (E/S), and SDME sensor. As for the symbol for sensors, there

are six colors to show the priority: white (CCRP), cyan (Radar), green (GPS), magenta

(AIS), orange (E/S) and blue (SDME) in that order.

1. Access the [Common Installation Setting] menu and click [Own Ship Setting] on

the tab bar.

2. Activate each field and enter own ship’s data, using the table below for reference.

Menu item/interactive field Description

[Vessel Type] Own ship type among [Fast/Super Small], [Fast/

Small], [Slow/Big] and [Super Tanker].

[Ship Length (LOA, m)] Own ship’s length, in meters.

[Ship Width (m)] Own ship’s width, in meters.

[Summer Load Line (m)] Distance between own ship’s hull and the summer

load line, in meters.

[MAX ROT (deg/min)] Own ship’s maximum angular velocity (Rate of turn).

[Block Coefficient] Own ship’s block coefficient.

[Min Maneuvering Speed (kn)] Minimum maneuvering speed. This value is used as

the threshold for the alert 159 "Low Speed Alarm".

The TCS is available when the vessel cruise at the set-

ting speed or more.

Note: Keep in mind the performance of the autopilot to

set the own ship’s minimum maneuvering speed.

[Center of Gravity] Own ship’s center of gravity, in meters, set by X, Y and

Z axis.

[Pivot Point] Own ship’s pivot point, in meters, set by X, Y and Z

axis. Approximately 80% of the ship’s length is recom-

mended for the pivot point. For example, the ship’s

length is 350 m, enter "280 m" to [Y (m)]. For TCS, the

XTE is calculated on the value set at here.

[CCRP] Select the [CCRP] you wish to setup by left-clicking the

check box to the left of each CCRP number. You can

set up a maximum of four CCRP positions. Set up of

[CCRP1] is required.

1. INITIAL SETTING AND ADJUSTMENT

1-14

3. Click [Radar Antenna] on the menu bar.

Note: When you set the value for [Antenna Position] on the [Installation Parame-

ters] menu, the setting value is shown at the right of [Equipment ID].

4. According to the number of antenna units connected to the processor unit, check

applicable checkbox to activate the antenna unit(s).

You can enter up to four antenna unit position data. Setting range: [RAS001] to

[RAS004]. Do not select [RAS005] to [RAS010]. Setup the antenna units activated

here on the [Installation Parameters] menu. See subsection 1.4.5 for details.

Note 1: Check all the antenna unit connected to the processor unit.

Note 2: For an FAR-27 and FAR-28 series radar antenna, set the antenna

no. (Equipment ID), taking care not to duplicate the Equipment ID of other radars.

For how to set the antenna no., see the installation manual of the radar.

5. Enter the position data of antenna unit(s) in the boxes [X (m)], [Y (m)], and [Z (m)].

Note: For the Chart Radar, the value of [Z (m)] is reflected in the default setting

on [MENU][1 ECHO][1 CUSTOMIZE ECHO][9 CONDITION][2 STC ANT

HEIGHT].

6. Enter the information for the GPS sensor, AIS transponder, echo sounder, and

SDME sensor in a similar manner.

Note 1: For the Chart Radar, [RAS001] (antenna unit), [GPS001] (GPS sensor),

[AIS001] (AIS transponder), and [LOG001] (SDME sensor) are activated by de-

fault. Enter their position data.

Note 2: When using the Radar Connection Box (RCB-002), make sure you input

the location information for the external radar antenna. Also, when multiple RCB-

002s are connected to the same network, change the IP address of the RCB-

002s, referring to "RCB-002 IP ADDRESS SETTING" on page AP-4.

Page is loading ...

Furuno FCR-2119-BB User manual

Furuno FCR-2119-BB User manual

Furuno FCR-2119-BB User manual

Related papers

Other documents