© Copyright 2019 Elo Touch Solutions, Inc. 1
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
E514693 ELO-SELF-SERV-STAND-SLIM-COUNTERTOP
E514881 ELO-SELF-SERV-STAND-SLIM-FLOOR-TOP
E515260 ELO-SELF-SERV-STAND-SLIM-FLOOR-BASE
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
© Copyright 2019 Elo Touch Solutions, Inc. 2
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
Contents for Kit: E514693 ELO-SELF-SERV-STAND-SLIM-COUNTERTOP
Tie-wrap
Qty. 2
Head Assembly
Qty. 1
Screws / Mounting hardware
Bag IQty.8 SCREW, M4X8L, PAN-HEAD,
CROSS-RECESS
Bag LQty.4 SCREW, M4X6L, PAN-HEAD,
CROSS-RECESS
Bag MQty.4 SCREW, M4X18L, PAN-HEAD,
CROSS-RECESS
Bag NQty.4 SCREW, M4X12L, PAN-HEAD,
CROSS-RECESS
Panel Hardware
Qty.2 SCREW, M6X14, PAN-HEAD, CROSS-
RECESS
Qty.2 BACKER BOARD SPACER
Qty.2 THUMB SCREW
Countertop Base
Qty. 1
© Copyright 2019 Elo Touch Solutions, Inc. 3
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
Contents for Kit: E514881, ELO-SELF-SERV-STAND-SLIM-FLOOR-TOP
Straps
Qty. 1
Tower Assembly
Qty. 1
Tie-wrap
Qty. 2
Screws / Mounting hardware
Bag IQty.8 SCREW, M4X8L, PAN-HEAD,
CROSS-RECESS
Bag LQty.4 SCREW, M4X6L, PAN-HEAD,
CROSS-RECESS
Bag M Qty.4 SCREW, M4X18L, PAN-HEAD,
CROSS-RECESS
Bag NQty.4 SCREW, M4X12L, PAN-HEAD,
CROSS-RECESS
Bag KQty.6 SCREW M5X12 FLAT HEAD,
CROSS-RECESS, BLACK
Panel Hardware
Qty.2 SCREW, M6X14, PAN-HEAD, CROSS-
RECESS
Qty.2 BACKER BOARD SPACER
Qty.2 THUMB SCREW
© Copyright 2019 Elo Touch Solutions, Inc. 4
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
Contents for Kit: E515260 ELO-SELF-SERV-STAND-SLIM-FLOOR-BASE
Base plate
Qty. 1
© Copyright 2019 Elo Touch Solutions, Inc. 5
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
Remove and save (4) screws from
stand with provided hex wrench,
pull off rear cover.
1 2
For Floor Stand, skip to step 5
For Countertop Stand, continue to step 2
Attach head to counter top plate
using (4) screws from bag “I”.
© Copyright 2019 Elo Touch Solutions, Inc. 6
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
Top Landscape
Cable
direction
Add (2) screws from bag “L” to top VESA
positions. Leave ~3mm (1/8”) gap for mounting
to display bracket.
Android Landscape
(For Portrait, go to step 5)
34
Tie-wrap cables
here as needed.
Assemble the display to top slotted holes
on stand. Add additional (2) screws from
bag “L” to bottom VESA mount holes to
secure the display.
© Copyright 2019 Elo Touch Solutions, Inc. 7
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
Add (2) screws from bag “L” to top VESA
positions. Leave ~3mm (1/8”) gap for mounting
to display bracket.
56
Tie-wrap cables
here as needed.
Assemble the display to top slotted holes on stand.
Add additional (2) screws from bag “L” to bottom
VESA mount holes to secure the display.
Android Portrait
Top Portrait
Cable
direction
© Copyright 2019 Elo Touch Solutions, Inc. 8
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
8
Windows Landscape
(For Portrait, go to step 9)
15” Landscape
15”: add (2) screws from bag “M” to top 75mm VESA positions.
22”: add (2) screws from bag “N” to top 75mm VESA positions.
Leave ~3mm (1/8”) gap for mounting to display bracket.
22” Landscape
Tie-wrap cables
here as needed.
Assemble the display to top slotted holes
on stand. Add additional (2) screws from
bag “L” to bottom VESA mount holes to
secure the display.
7
Tie-wrap cables
here as needed.
© Copyright 2019 Elo Touch Solutions, Inc. 9
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
15” Portrait
15”: add (2) screws from bag “M” to top 75mm VESA positions.
22”: add (2) screws from bag “N” to top 100mm VESA positions.
Leave ~3mm (1/8”) gap for mounting to display bracket.
22” Portrait
9Windows Portrait 15” Portrait
Assemble the display to top slotted holes on stand.
Add additional (2) screws from bag “L” to bottom
VESA mount holes to secure the display.
10a
Tie-wrap cables
here as needed.
© Copyright 2019 Elo Touch Solutions, Inc. 10
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
11
Route cables through bottom of stand.
Attach back cover using screws saved
from step 1.
END for Countertop Stand
22” Portrait
Tie-wrap cables
here as needed.
10b
Assemble the display to top slotted holes on stand.
Add additional (2) screws from bag “L” to bottom
VESA mount holes to secure the display.
© Copyright 2019 Elo Touch Solutions, Inc. 11
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
Assemble base plate to tower using
(4) screws from bag “K”.
Remove and save (4) screws on the
left and right of the stand tower. Pull
off the silver cover and set aside.
Add (2) more screws from bag “K” at
bottom front of tower.
13
12
Add (2) more screws from bag “K”.
© Copyright 2019 Elo Touch Solutions, Inc. 12
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
Top Landscape
Cable
direction
Add (2) screws from bag “L” to top VESA
positions. Leave ~3mm (1/8”) gap for mounting
to display bracket.
Android Landscape
(For Portrait, go to step 16)
14 15
Tie-wrap cables
here as needed.
Assemble the display to top slotted holes on stand.
Add additional (2) screws from bag “L” to bottom
VESA mount holes to secure the display.
© Copyright 2019 Elo Touch Solutions, Inc. 13
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
Add (2) screws from bag “L” to top VESA
positions. Leave ~3mm (1/8”) gap for mounting
to display bracket.
16 17
Tie-wrap cables
here as needed.
Assemble the display to top slotted holes on
stand. Add additional (2) screws from bag “L” to
bottom VESA mount holes to secure the display.
Android Portrait
Top Portrait
Cable
direction
© Copyright 2019 Elo Touch Solutions, Inc. 14
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
19
Windows Landscape
(For Portrait, go to step 20)
15” Landscape
15”: add (2) screws from bag “M” to top 75mm VESA positions.
22”: add (2) screws from bag “N” to top 75mm VESA positions.
Leave ~3mm (1/8”) gap for mounting to display bracket.
22” Landscape
Tie-wrap cables
here as needed.
Assemble the display to top slotted holes
on stand. Add additional (2) screws from
bag “L” to bottom VESA mount holes to
secure the display.
18 15”/22” Landscape
© Copyright 2019 Elo Touch Solutions, Inc. 15
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
15” Portrait
15”: add (2) screws from bag “M” to top 75mm VESA positions.
22”: add (2) screws from bag “N” to top 100mm VESA positions.
Leave ~3mm (1/8”) gap for mounting to display bracket.
22” Portrait
20 Windows Portrait 15” Portrait
Assemble the display to top slotted holes on stand.
Add additional (2) screws from bag “L” to bottom
VESA mount holes to secure the display.
21a
Tie-wrap cables
here as needed.
© Copyright 2019 Elo Touch Solutions, Inc. 16
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
21b22
Add power brick into tower
using provided strap. Route
additional cables through
base, tower, head as needed.
22” Portrait
Assemble the display to top slotted holes on stand.
Add additional (2) screws from bag “L” to bottom
VESA mount holes to secure the display.
Tie-wrap cables
here as needed.
© Copyright 2019 Elo Touch Solutions, Inc. 17
ASSEMBLY INSTRUCTIONS, SLIM SELF-SERVICE STAND
23 24
Replace floor stand cover and secure
using (4) screws saved from step 6.
Two bolt holes (14mm [0.55”] dia. X2) are
available on top of base to secure stand to
floor. Feet can be adjusted in case of
uneven surfaces.
END for Floor Stand
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Elo TouchSystems E796783 Quick Install Guide
-
Elo Wallaby™ Self-Service Stands User guide
-
-
-
-
-
-
-
-
Other documents
-
Elo Touch Solution 1931L User manual
-
CyberResearch STH 15B Series User manual
-
-
-
Apollo APOLLO 150 User manual
-
Carf-Models Ultra Lightning Owner's manual
-
-
-
-
Elo Touch Solution ET4201L User manual