NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
WARNING
HOT GLASS WILL CAUSE BURNS. DO NOT
TOUCH GLASS UNTIL COOLED.
NEVER ALLOW
CHILDREN TO TOUCH GLASS.
• Fireplaces surfaces get EXTREMELY HOT!
• Install only when fireplace is OFF and COLD.
• The glass on the front of the fireplace reaches
EXTREMELY HIGH temperatures and can cause severe
burns if touched. Even after the gas is turned off,
fireplace surfaces remain extremely hot.
• Keep children away from an operating fireplace. Closely
supervise children in any room where a fireplace is
operating to prevent contact with glass.
CAUTION
RISK OF PERSONAL INJURY OR PROPERTY DAMAGE.
• Never operate fireplace with glass door assemblies removed.
• Securely tighten door latch screws when reinstalling
glass door assemblies to prevent doors from falling out.
• Handle glass door assemblies with extreme care.
Replace damaged glass door assemblies with approved
replacement assemblies only.
• The door assemblies contain ceramic glass. Handle
with care to prevent damage. If the door frame or
glass becomes damaged, replace the entire glass door
assembly with a manufacturer-approved replacement
assembly only. Do not attempt to substitute any
materials used on door assemblies or replace cracked or
broken glass with any other materials.
KIT CONTENTS
• (1) Safety Guard
• (6) Flush-face Safety Guard Brackets
• (6) Rhapsody® Surround Safety Guard Brackets
• (6) Sirius Surround Safety Guard Brackets
• (6) Bracket Clips
• (12) #10 Sheet Metal Screws
REQUIRED TOOLS
• Phillips Screwdriver
GENERAL INFORMATION
The optional safety guard is designed to prevent incidental
contact with the glass front of the fireplaces listed in Table 1
when it is installed and used in accordance with these
installation instructions and the warnings, precautions, and
instructions included in the Installation Instructions and the
Care and Operation Instructions provided with the appliance.
NOTE: Improper or repeated installation and removal of
the optional safety guard could scratch, dent, or otherwise
damage the glass front of the appliance or the metal frame
surrounding it.
HEARTH PRODUCTS
KITS AND ACCESSORIES
P/N 900077-09
Rev. NC 10/2014
RHAPSODY AND DRL6500 LINEAR
FIREPLACES SAFETY GUARD KIT
INSTALLATION INSTRUCTIONS FOR SAFETY GUARD KIT
FOR USE ON RHAPSODY DRL6500, SIRIUS, and DRL3000 LINEAR DIRECT-VENT GAS FIREPLACES
Fireplace Model Safety Guard
Cat. No.
Safety Guard
Model No.
42" Models H8565 SG-26
54" Models H8541 SG-23
Table 1: Linear Fireplaces Compatible with the
Safety Guard Kit
INSTALLATION INSTRUCTIONS
NOTE: The safety guard kit includes mounting hardware
for flush-face and surround-equipped Rhapsody and Elite
linear fireplaces.
1. Using Figure 1, identify and separate the eighteen (18)
safety guard brackets into three groups: six (6) flush-face
safety guard brackets, six (6) Rhapsody surround safety
guard brackets, and six (6) Sirius surround safety guard
brackets. Choose the correct safety guard brackets for the
desired application, and discard the remaining brackets.
Flush-Face Safety
Guard Bracket
Rhapsody Surround
Safety Guard Bracket
Elite and Sirius Sur-
round Safety
Guard Bracket
Figure 1: Identifying the Safety Guard Brackets
2. Install one bracket clip onto the flat end of each safety
guard bracket by sliding the bracket clip over the bracket
and aligning the holes, as shown in Figure 2.
Figure 2: Installing the Bracket Clips
P900077-09
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
INNOVATIVE HEARTH PRODUCTS• SAFETY GUARD KIT • LINEAR DIRECT-VENT GAS FIREPLACES • INSTALLATION INSTRUCTION SHEET
Printed in U.S.A. © 2014 Innovative Hearth Products
P/N 900077-09 Rev. NC 07/2014
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
IHP.us.com
3. For surround-equipped fireplaces, only:
Gently pull out the lower edge of the bezel to detach it from
the lower edge of the glass door frame. Then, swing the
lower edge of the bezel away from the door and lift up to
unhook the bezel upper flange from the top edge of the
glass door frame, as shown in Figure 3.
Bezel Upper
Flange
Glass Door
Frame
Bezel Lower Flange
Figure 3: Removing the Bezel
4. Position and secure the six (6) safety guard brackets
identified in step 1, using the supplied screws, onto the
fireplace in the holes shown in Figure 4.
NOTE: The are two screw hole options for each of the
bottom safety guard brackets installation positions. Either is
acceptable for installation.
Figure 4: Safety Guard Bracket Screw Holes
Figure 5: Completed Safety Guard Bracket Installation
5. For surround-equipped Rhapsody fireplaces, only:
Reverse the process in step 3 to reinstall the bezel.
6. Position the safety guard on the safety guard brackets as
shown in Figure 6. Ensure the holes in the safety guard
brackets and the safety guard are aligned.
Figure 6: Installing the Safety Guard
NOTE: Flush-Face application shown.
7. Secure the safety guard to the safety guard brackets with
the included screws.
Innovative Hearth Products reserves the right to make
changes at any time, without notice, in design, materi-
als, specifications, prices and also to discontinue colors,
styles, and products. Consult your local distributor for
fireplace code information.
P900077-09
-
1
-
2
Astria Fireplaces DRL65 Instruction Sheet
- Type
- Instruction Sheet
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Superior DRL3042TEP Installation And Operation Instructions Manual
-
Lennox ELITE LDV54N Installation Instructions Manual
-
Superior Fireplaces VRL3000 Operating instructions
-
-
-
-
-
RSF Woodburning Fireplaces Opel AP Owner's manual
-
-