Element4 Club Series E-smart Operating instructions

Category
Fireplaces
Type
Operating instructions
App Pairing Instructions for
IOS and E–tab
Applicable to all Element4 Club eSeries models
English
E-Tab Controller:
1. Volume control
2. Power Buon—Press and hold for 3 seconds to turn ON/OFF
3. USB charging point
4. USB connecon lead and plug socket
1. 2.
3.
4.
1. Access either the Apple app store or Google play, this is
depending on the operang system of your smart phone or
tablet.
2. Search, locate, and download the app entled evonic e-smart.
The e-smart app can be used with both smart phone and tablet
devices.
Ulising the e-smart app will allow complete controllability of your
Evonic product.
To download the Evonic e-smart app please follow the below steps.
Please note: E-Tab control system comes with e-smart app already installed
Connecting a device to an Element4 product:
3. Once your appliance has been installed and turned on, go to the wi-fi settings on your
device and select the fire. Each fire has a unique Wi-Fi settings name which you can find
in the table below. This will connect your device to the fire. Fig 1.
4. Open your E-Smart app, and in the settings panel ( Fig 2.) establish your connection by
selecting your home wi-fi. This will pair the fire with your router. Fig 3.
5. Your evonic product will now be paired and ready to operate.
6. Under the settings panel located in the app, you can now change the name of your fire.
Ensure you enter your e-mail address, as this is to identify between the fireplace and you.
You can also change units of temperature. Fig 4.
Fig 1. Fig 2. Fig 3. Fig 4.
Table 1.
Name of Name Wi-fi
Fireplace Configuration Network
Club 80e F/C/3S Tyrell
Club 100e F/C/3S Kalmar
Club 100e T Lindstrom
Club 150e F/C/3S Linnea
Ovation e Halden
Selecng your re:
1.
2.
3.
1. Once your product is paired, open the app. The above
screen will appear with your re shown. Single press
Kalmar. Please note: It may take a few minutes for your re
to appear on the screen.
2. Single press the ame icon to turn on the lights.
3. Single press the heater buon to turn on the heater
App Control Overview:
A
C
D
E F
G
H
B
A). Target Temperature—This displays the desired room temperature.
B). Temperature Control— Temperature adjustor. Press, hold and swipe to adjust.
C). Animaon seng— Displays selected animaon. Single press arrow to reveal drop-down menu.
D). Side Lights— Single press to turn on side lights.
E). Lighng—Single press to turn on/o the fuel, ame & overbed lighng.
F). Flame— Slide le or right to adjust brightness of ame.
G). Fuel— Slide le or right to adjust brightness of fuel bed.
H). Speed— Single press to adjust the speed of selected animaon.
Pairing with Alexa:
1. Once you re is installed and fully funconing, download
the Amazon Alexa app.
2. Congure your echo with the Amazon app by adding device.
3. On the home screen, you will see a menu icon in the top le
hand side. Single press to open the menu and select skills
and games
4. Once open, in the top right corner search evonicand the
below skill opon will appear. Fig 1.
4. Single press to select skill, which will then open up the
below page. Fig 2.
5. Once you press ENABLE TO USE, you will be directed to
the evonet page.
6. To complete pairing, Input the evonet account details you
registered earlier in the e-smart app setup. You re is now
paired with Alexa.
Fig 1 Fig 2
Element4 B.V.
Paxtonstraat 23, 8013RP Zwolle, The Netherlands
Phone: +31(0)38 - 420 90 20
Element4.nl
Problem Solving:
1. e-smart app will not connect to product and is
connuously showing the below screen: Please follow the
below steps.
1. Force close the app by pressing the square at the boom of
your phone/e-tab. Then aempt to re-launch the app.
2. Ensure that the rocker switch is in the ON posion, and
re-scan for the product.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Element4 Club Series E-smart Operating instructions

Category
Fireplaces
Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI