800.524.2744 www.LCDarms.com
STEP 1 | COLUMN ................................................................................................................... Page 3
STEP 2 | MOUNT .........................................................................................................................Page 4
STEP 3 | WORK SURFACE ...............................................................................Page 5
STEP 4 | BEAM ................................................................................................................................Page 6
STEP 5 | MONITOR TILTER..............................................................................Page 7
STEP 6 | MONITOR CUPS ..................................................................................Page 8
STEP 7 | CABLE MANAGEMENT .....................................................Page 9
3
4
7
1
2
5
6
© 2017 Innovative Office Products, LLC P512137 REV C
NOTE: Depending on your Winston Workstation® configuration,
you may not receive all the parts shown within this instruction booklet.
Installation may require two people.
WNST-APL-1 & WNST-APL-2
Winston Workstation® for Apple iMac | Installation Instructions
PAGE 1 OF 10
800.524.2744 www.LCDarms.com
WNST-APL-1 & WNST-APL-2
Winston Workstation® for Apple iMac | Parts List
Depending on your Winston Workstation® conguration,
you may not receive all parts shown below.
A Work Surface
1114 3 5
B Column
411470
C Felt Pad
111464
D Freestanding Base
11124 8
E Cable Retainer
11173 5
F 3/8-16 x 1" FHSCS
701124
G Screws
713273
H Top Plate
11173 6
I Utility Tray
113 0 2 5
J FHSCS 10-32 x 1-1/2”
711101
K Center Beam (10” or 30”)
1110 9 8 -10 o r 1110 9 8 - 3 0
L Column Clamp
1110 4 0
M 1/8" Allen Wrench
701312
N 7/32" Allen Wrench
70112 7
O End Cap
11115 9 -7 0 8
P Column Cap
1112 7 5 -7 0 8
Q 10-32 x 3/8" PhPHS
702281
R 75/100 mm VESA Adapter
105587
S Standard Monitor Tilter
405397
T M4 x 12mm PhPHS
702096
U Monitor Cup
4113 51
V Dog Washer
1112 3 0 - 6 0 3
W 10-32 x 1/2" FHSCS
71124 0
X Column Cable Clip
1112 0 3 -7 0 8
PAGE 2 OF 10
800.524.2744 www.LCDarms.com
COLUMNSTEP 1
i
1 2 3
A
B
Use 7/32" Allen wrench to
press cable firmly into place.
Confirm cable is
properly seated
into position.
N
IMPORTANT: Do not pull excessively
on cable – doing so may result in
accidental actuation of column.
PAGE 3 OF 10
800.524.2744 www.LCDarms.com
MOUNTSTEP 2
1 2 3
4 5
D
C
Hang base plate over edge of
work surface to allow access
to countersunk holes. Side
of base plate with felt pads
should be face down.
Place work surface
on base plate to aid as a
counterbalance.
F
7/32"
E
PAGE 4 OF 10
800.524.2744 www.LCDarms.com
WORK SURFACESTEP 3
1 2
I
Slide utility tray onto work surface.
Utility tray simply rests on top of
work surface.
H
G
PAGE 5 OF 10
800.524.2744 www.LCDarms.com
BEAMSTEP 4
1
3
2
4
1/8"
1/8"
L
J
K
1
4 5
2 3
M
N
O
P
IMPORTANT: Tighten bolts evenly.
The beam should sit flush against
the column, ensure there are no gaps.
Also, it is important the work surface
clamp is level.
i
PAGE 6 OF 10
800.524.2744 www.LCDarms.com
MONITOR TILTERSTEP 5
1 2
NOTE:
Requires VESA compatible iMac
or Apple VESA adapter
(not included).
Q
R
S
T
PAGE 7 OF 10
800.524.2744 www.LCDarms.com
MONITOR CUPSSTEP 6
i
1/8"
1 2
7/32"
U
U
V
W
PAGE 8 OF 10
800.524.2744 www.LCDarms.com
CABLE MANAGEMENTSTEP 7
1
X
PAGE 9 OF 10
800.524.2744 www.LCDarms.com
HEIGHT ADJUSTMENT
iIs your height adjust button not working?
If so, make the adjustments below.
Slide workstation so that
the work surface hangs over
desk edge to allow access to
underneath the work surface.
Loosen the two screws
as shown.
Slide bracket in the direction
shown and tighten screws.
Test height adjust button –
readjust by repeating the steps
above as necessary.
1
2
3
4
Press button and hold. Lift up/down. Release to lock in place.
PAGE 10 OF 10
/
