NOTE:
Depending on your
Winston Workstation®
conguration, you
may not receive all the
parts shown within this
instruction booklet.
Installation may require
two people.
CAUTION:
Mechanism can rise quickly
with no equipment in place.
User equipment must be
properly installed, prior to
height adjustment. Failure
to do so may result in
personal injury and/or
property damage.
WNST-1 WNST-2
© 2022 Human Active Technology, LLC P516332 REV B
WINSTON WORKSTATION
Installation Instructions
Human Active Technology
800 524 2744
customerservice@team-hat.com
team-hat.com
®
PAGE 1 OF 11
A Worksurface
111435
B Column
411470
C Felt Pad
111464
D Freestanding Base
111248
E Cable Retainer
111735
F 3/8-16 x 1" FHSCS
701124
G Screws
713273
H Top Plate
111736
I Utility Tray
113025
J 10-32 x 1" FHSCS
711467
K Beam (10" or 30")
412036 or 412037
L Column Clamp
111040
M 1/8" Allen Wrench
701312
N 7/32" Allen Wrench
701127
O Column Cap
111275-708
P Quick Connect VESA Plate
114808
Q M4 x 12mm Phillips Pan Head Screw
701153
R Monitor Tilter
8500 Tilter
S Dog Washer
111230-603
T 10-32 x 1/2" FHSCS
711240
U Column Cable Clip
111203-708
Depending on your Winston Workstation® configuration,
you may not receive all parts shown below.
PARTS LIST
PAGE 2 OF 11
i
A
B
Use 7/32" Allen wrench to
press cable rmly into place.
Conrm cable is
properly seated
into position.
N
IMP OR TAN T: Do not pull excessively
on cable – doing so may result in
accidental actuation of column.
CAUTION: Do not press height adjust
button until unit is fully assembled.
1a 1b 1c
1
PAGE 3 OF 11
D
C
Hang base plate over edge
of worksurface to allow
access to countersunk
holes. Side of base plate
with felt pads should be
face down.
Place worksurface
on base plate to aid
as a counterbalance.
F
E
2 3 4
5 6
7/32"
PAGE 4 OF 11
I
Slide utility tray onto
worksurface. Utility
tray simply rests on
top of worksurface.
H
G
7 8
PAGE 5 OF 11
L
J
K
O
M
910
11 12
iIMPORTANT:
Tighten bolts evenly.
The beam should sit
ush against the col-
umn, ensure there
are no gaps. Also,
it is important the
worksurface clamp
is level.
1
3
2
4
1/8"
1/8"
PAGE 6 OF 11
13
Q
Q
P
PAGE 7 OF 11
R
14
PAGE 8 OF 11
15
i
1/8"
M
S
T
T
1/8"
iTILTER FRICTION ADJUSTMENT
M
1/8"
PAGE 9 OF 11
U
16
PAGE 10 OF 11
iIS YOUR HEIGHT ADJUST BUTTON NOT WORKING?
If so, make the adjustments below.
Slide workstation so that
the worksurface hangs over
desk edge to allow access to
underneath the worksurface.
Loosen the two screws
as shown.
Slide bracket in the direction
shown and tighten screws.
Test height adjust button –
readjust by repeating the steps
above as necessary.
Press button and hold. Lift up/down. Release to lock in place.
17a
17b
17c
17d
17
PAGE 11 OF 11
/
