Avantco MX60 is a 60-quart commercial mixer designed for heavy-duty mixing tasks in bakeries, restaurants, and commercial kitchens. It features three speeds for different mixing requirements, a powerful motor for efficient operation, and a sturdy construction for durability. The mixer comes with a dough hook, a flat beater, and a wire whip for versatile mixing options. It also includes a bowl and a spatula for easy ingredient handling.
Avantco MX60 is a 60-quart commercial mixer designed for heavy-duty mixing tasks in bakeries, restaurants, and commercial kitchens. It features three speeds for different mixing requirements, a powerful motor for efficient operation, and a sturdy construction for durability. The mixer comes with a dough hook, a flat beater, and a wire whip for versatile mixing options. It also includes a bowl and a spatula for easy ingredient handling.
User Manual
www.AvantcoEquipment.com 1
Gear Driven 60 Qt. Commercial Mixer
Models: MX60
Please read and keep these instructions. Indoor use only.
Shifting gears while this unit is
running will void warranty. 02/2022
User Manual
User Manual
2 www.AvantcoEquipment.com
Index
Standard Accessories .................................................... 3
Operation Instructions .................................................. 3
Mixer Capacity Chart ..................................................... 4
Figure 1: Top Cover and Hand Cart ............................... 5
Figure 2: Center Axle ..................................................... 6
Figure 3: Gear Axle ........................................................ 7
Figure 4: Motor ............................................................... 8
Figure 5: Fork ................................................................. 9
Figure 6: Speed Block ................................................. 10
Figure 7: Bowl Lifter Unit ............................................. 11
Figure 8: Turning Plate and Mixing Axle ..................... 12
Figure 9: Electromotion Type Bowl Lifter Unit ........... 13
Three Phase Motor Diagram ........................................ 14
Troubleshooting ........................................................... 15
User Manual
www.AvantcoEquipment.com 3
Standard Accessories
1312
STANDARD ACCESSORIES
FIGURE 10
NEMA 5015P
110 V
110V
OPERATION INSTRUCTION
ITEM DESCRIPTION QTY
1 Spatula 1
2 Dough Hook 1
3 Wisk 1
4 Bowl 1
NOTES:
โข Any agitator is easily installed by sim-
ply raising it onto the mixing axle, and
the rotating it clockwise on the shaft
until into place. To remove, raise the
agitator on the shaft until it clears the
lock and then rotate counter-clockwise
and lower.
โข All of tools are precisely fitted to the
bowl, rounded corners and easily
removable for cleaning.
SPANISH:
โข Any agitator is easily installed by sim-
ply raising it onto the mixing axle, and
the rotating it clockwise on the shaft
until into place. To remove, raise the
agitator on the shaft until it clears the
lock and then rotate counter-clockwise
and lower.
โข All of tools are precisely fitted to the
bowl, rounded corners and easily
removable for cleaning.
OFF
Please ensure power supply matches your machine
Please ensure power supply matches your machine.
FOR CHANGING THE SPEED: Please stop machine first
before changing speed in order to avoid damage to the gear box
FOR CHANGING THE SPEED: Please stop machine first
before changing speed in order to avoid damage to the gear bo
MIXING: According to the different mixing material.
Choose the different mixing devicews and speed.
MIXING: According to the different mixing material.
Choose the different mixing devicews and speed.
A. Be suitable for mix and stir batter, eggs and work with
in speed speed, working time isless than 15 minutes.
A. Be suitable for mix and stir batter, eggs and work with
in speed speed, working time isless than 15 minutes
B. Be suitable for mix and stir stuffing and raw material, and
work in middle speed, working time is less than 20 mins.
B. Be suitable for mix and stir stuffing and raw material, and
work in middle speed, working time is less than 20 mins.
C. Middle position is suitable for mixing dough, working time
is less than 30 minutes. Flour/ water quantity is 40%-50%.
C. Middle position is suitable for mixing dough, working time
is less than 30 minutes. Flour/ water quantity is 40%-50%.
A
B
C
1312
STANDARD ACCESSORIES
FIGURE 10
NEMA 5015P
110V
110V
OPERATION INSTRUCTION
ITEM DESCRIPTION QTY
1 Spatula 1
2 Dough Hook 1
3 Wisk 1
4 Bowl 1
NOTES:
โข Any agitator is easily installed by sim-
ply raising it onto the mixing axle, and
the rotating it clockwise on the shaft
until into place. To remove, raise the
agitator on the shaft until it clears the
lock and then rotate counter-clockwise
and lower.
โข All of tools are precisely fitted to the
bowl, rounded corners and easily
removable for cleaning.
SPANISH:
โข Any agitator is easily installed by sim-
ply raising it onto the mixing axle, and
the rotating it clockwise on the shaft
until into place. To remove, raise the
agitator on the shaft until it clears the
lock and then rotate counter-clockwise
and lower.
โข All of tools are precisely fitted to the
bowl, rounded corners and easily
removable for cleaning.
OFF
Please ensure power supply matches your machine
Please ensure power supply matches your machine.
FOR CHANGING THE SPEED: Please stop machine first
before changing speed in order to avoid damage to the gear box
FOR CHANGING THE SPEED: Please stop machine first
before changing speed in order to avoid damage to the gear bo
MIXING: According to the different mixing material.
Choose the different mixing devicews and speed.
MIXING: According to the different mixing material.
Choose the different mixing devicews and speed.
A. Be suitable for mix and stir batter, eggs and work with
in speed speed, working time isless than 15 minutes.
A. Be suitable for mix and stir batter, eggs and work with
in speed speed, working time isless than 15 minutes
B. Be suitable for mix and stir stuffing and raw material, and
work in middle speed, working time is less than 20 mins.
B. Be suitable for mix and stir stuffing and raw material, and
work in middle speed, working time is less than 20 mins.
C. Middle position is suitable for mixing dough, working time
is less than 30 minutes. Flour/ water quantity is 40%-50%.
C. Middle position is suitable for mixing dough, working time
is less than 30 minutes. Flour/ water quantity is 40%-50%.
A
B
C
Item Description Qty
1 Flat Beater 1
2 Dough Hook 1
3 Wire Whip 1
4 Bowl 1
NOTES:
โข Any agitator is easily installed by simply raising it onto the mixing axle, and the rotating it clockwise on the shaft
until it locks into place. To remove, raise the agitator on the shaft until it clears the lock and then rotate counter-
clockwise and lower.
โข All of the accessories are precisely fitted to the bowl, have rounded corners, and are easily removed for cleaning.
Unpacking the Equipment
and Initial Setup
Carefully remove crating or packaging materials from the equipment. Models shipped on pallets are bolted to the pallet.
Bolts must be removed to safely separate the equipment from the pallet. Place the equipment on a flat surface with
sufficient space around the mixer to allow for safe cleaning and service.
This product must be hardwired; it does not plug into a standard wall outlet. Have a licensed electrician connect the
unit to the power supply.
INSTALLATION:
1. Read this manual in its entirety prior to installation and operation. DO NOT install if you do not understand everything
in this manual.
2. Select a location for the mixer keeping in mind that:
โข Surface must be level
โข Location should be accessible for maintenance and service
โข Location should offer adequate clearance for installing and removing agitators, bowls or attachments
โข Location offers sufficient space for adding ingredients to the mixer
โข Make sure that the rear ventilation outlet of the mixer is not blocked
User Manual
4 www.AvantcoEquipment.com
Operation Instructions
Please ensure that your power supply matches your machine
This mixer does not come with a plug and must be hard wired. Consult a professional Electrician
for installation.
For changing the speed: Please stop machine first before changing speed in order to avoid
damage to the gear box. Also make sure that the bowl is in fully lifted position and the guard is closed.
โข Slow Speed is the middle, dough hook setting. The knob will be facing forward.
โข Medium Speed is the bottom, flat beater setting. The knob will be straight down.
โข High Speed is the top, whisk setting. The knob will be straight up.
Mixing: Always use the correct attachment for the job.
A. Wire Whip: Suitable for mixing liquids and soft ingredients, can work in all speeds. Do not
run for more than 15 minutes.
B. Flat Beater: Suitable for mixing dry ingredients, can work in low & medium speeds only.
Do not use in high speed. Do not run for more than 15 minutes.
C. Dough Hook: Suitable for mixing dough, can work in low & medium speeds only. Do not
use in high speed, do not run for more than 20 minutes. Absorption ratio must be more than
50%. Refer to mixer capacity chart.
!
!
1312
STANDARD ACCESSORIES
FIGURE 10
NEMA 5015P
110V
110V
OPERATION INSTRUCTION
ITEM DESCRIPTION QTY
1 Spatula 1
2 Dough Hook 1
3 Wisk 1
4 Bowl 1
NOTES:
โข Any agitator is easily installed by sim-
ply raising it onto the mixing axle, and
the rotating it clockwise on the shaft
until into place. To remove, raise the
agitator on the shaft until it clears the
lock and then rotate counter-clockwise
and lower.
โข All of tools are precisely fitted to the
bowl, rounded corners and easily
removable for cleaning.
SPANISH:
โข Any agitator is easily installed by sim-
ply raising it onto the mixing axle, and
the rotating it clockwise on the shaft
until into place. To remove, raise the
agitator on the shaft until it clears the
lock and then rotate counter-clockwise
and lower.
โข All of tools are precisely fitted to the
bowl, rounded corners and easily
removable for cleaning.
OFF
Please ensure power supply matches your machine
Please ensure power supply matches your machine.
FOR CHANGING THE SPEED: Please stop machine first
before changing speed in order to avoid damage to the gear box
FOR CHANGING THE SPEED: Please stop machine first
before changing speed in order to avoid damage to the gear bo
MIXING: According to the different mixing material.
Choose the different mixing devicews and speed.
MIXING: According to the different mixing material.
Choose the different mixing devicews and speed.
A. Be suitable for mix and stir batter, eggs and work with
in speed speed, working time isless than 15 minutes.
A. Be suitable for mix and stir batter, eggs and work with
in speed speed, working time isless than 15 minutes
B. Be suitable for mix and stir stuffing and raw material, and
work in middle speed, working time is less than 20 mins.
B. Be suitable for mix and stir stuffing and raw material, and
work in middle speed, working time is less than 20 mins.
C. Middle position is suitable for mixing dough, working time
is less than 30 minutes. Flour/ water quantity is 40%-50%.
C. Middle position is suitable for mixing dough, working time
is less than 30 minutes. Flour/ water quantity is 40%-50%.
A
B
C
1312
STANDARD ACCESSORIES
FIGURE 10
NEMA 5015P
110V
110V
OPERATION INSTRUCTION
ITEM DESCRIPTION QTY
1 Spatula 1
2 Dough Hook 1
3 Wisk 1
4 Bowl 1
NOTES:
โข Any agitator is easily installed by sim-
ply raising it onto the mixing axle, and
the rotating it clockwise on the shaft
until into place. To remove, raise the
agitator on the shaft until it clears the
lock and then rotate counter-clockwise
and lower.
โข All of tools are precisely fitted to the
bowl, rounded corners and easily
removable for cleaning.
SPANISH:
โข Any agitator is easily installed by sim-
ply raising it onto the mixing axle, and
the rotating it clockwise on the shaft
until into place. To remove, raise the
agitator on the shaft until it clears the
lock and then rotate counter-clockwise
and lower.
โข All of tools are precisely fitted to the
bowl, rounded corners and easily
removable for cleaning.
OFF
Please ensure power supply matches your machine
Please ensure power supply matches your machine.
FOR CHANGING THE SPEED: Please stop machine first
before changing speed in order to avoid damage to the gear box
FOR CHANGING THE SPEED: Please stop machine first
before changing speed in order to avoid damage to the gear bo
MIXING: According to the different mixing material.
Choose the different mixing devicews and speed.
MIXING: According to the different mixing material.
Choose the different mixing devicews and speed.
A. Be suitable for mix and stir batter, eggs and work with
in speed speed, working time isless than 15 minutes.
A. Be suitable for mix and stir batter, eggs and work with
in speed speed, working time isless than 15 minutes
B. Be suitable for mix and stir stuffing and raw material, and
work in middle speed, working time is less than 20 mins.
B. Be suitable for mix and stir stuffing and raw material, and
work in middle speed, working time is less than 20 mins.
C. Middle position is suitable for mixing dough, working time
is less than 30 minutes. Flour/ water quantity is 40%-50%.
C. Middle position is suitable for mixing dough, working time
is less than 30 minutes. Flour/ water quantity is 40%-50%.
A
B
C
1312
STANDARD ACCESSORIES
FIGURE 10
NEMA 5015P
110V
110V
OPERATION INSTRUCTION
ITEM DESCRIPTION QTY
1 Spatula 1
2 Dough Hook 1
3 Wisk 1
4 Bowl 1
NOTES:
โข Any agitator is easily installed by sim-
ply raising it onto the mixing axle, and
the rotating it clockwise on the shaft
until into place. To remove, raise the
agitator on the shaft until it clears the
lock and then rotate counter-clockwise
and lower.
โข All of tools are precisely fitted to the
bowl, rounded corners and easily
removable for cleaning.
SPANISH:
โข Any agitator is easily installed by sim-
ply raising it onto the mixing axle, and
the rotating it clockwise on the shaft
until into place. To remove, raise the
agitator on the shaft until it clears the
lock and then rotate counter-clockwise
and lower.
โข All of tools are precisely fitted to the
bowl, rounded corners and easily
removable for cleaning.
OFF
Please ensure power supply matches your machine
Please ensure power supply matches your machine.
FOR CHANGING THE SPEED: Please stop machine first
before changing speed in order to avoid damage to the gear box
FOR CHANGING THE SPEED: Please stop machine first
before changing speed in order to avoid damage to the gear bo
MIXING: According to the different mixing material.
Choose the different mixing devicews and speed.
MIXING: According to the different mixing material.
Choose the different mixing devicews and speed.
A. Be suitable for mix and stir batter, eggs and work with
in speed speed, working time isless than 15 minutes.
A. Be suitable for mix and stir batter, eggs and work with
in speed speed, working time isless than 15 minutes
B. Be suitable for mix and stir stuffing and raw material, and
work in middle speed, working time is less than 20 mins.
B. Be suitable for mix and stir stuffing and raw material, and
work in middle speed, working time is less than 20 mins.
C. Middle position is suitable for mixing dough, working time
is less than 30 minutes. Flour/ water quantity is 40%-50%.
C. Middle position is suitable for mixing dough, working time
is less than 30 minutes. Flour/ water quantity is 40%-50%.
A
B
C
User Manual
www.AvantcoEquipment.com 5
Product Agitator and Speed Maximum Bowl
Capacity
Bread and Roll Dough -60 % AR Dough Hook - 1st only 50 lb.
Heavy Bread Dough -55% AR Dough Hook - 1st only 40 lb.
Pizza Dough, Thin -40% AR Dough Hook - 1st only 25 lb.
Pizza Dough, Medium -50% AR Dough Hook - 1st only 35 lb.
Pizza Dough, Thick -60% AR Dough Hook - 1st only 40 lb.
Raised Donut Dough -65% AR Dough Hook - 1st and 2nd 25 lb.
Mashed Potatoes Flat Beater 35 lb.
Waffle or Hot Cake Batter Flat Beater 20 qt.
Egg Whites Wire Whisk 2 qt.
Whipped Cream Wire Whisk 6 qt.
Cake Batter Flat Beater 35 lb.
When mixing dough ( pizza, bread or bagels), check your "AR" absorption ratio - water weight divided by flour weight.
Above capacities based on 12% flour moisture at 70ยฐF water temperature. If high gluten flour is used, reduce above
dough batch size by 10%.
Example: If recipe calls for 5 lb. of water and 10 lb. of flour, then 5 divided by 10 = 0.50 x 100 = 50 %AR.
โข 2nd Speed should never be used on mixtures with less than 50% AR.
โข Do not use attachments on hub while mixing.
When calculating the correct size mixer for your application, here are some helpful weights & measures:
โข 8.3 lb. = 1 gallon of water โ 2.08 lb. = 1 Quart.
Mixer Capacity Chart
User Manual
6 www.AvantcoEquipment.com
TOP COVER AND HAND CART
Figure 1
2
1
3
4
5
6
7
8
9
10
11
12
13
14
15
Inner gear
Screw
Nut
Plantaty gear
Bearing
Turning plate
Spring gasket
Nut
Bearing
1
6
1
1
1
1
1
1
1
1
1
1
1
Gasket
Oil seal
Mixing axle
1
Spring gasket 1
3
4
5
6
1
27
8
9
11
12
13
10
14
15
Pin
Key
10
Qty
Descviption
16
16 1
Safety net
1
23
4
5
6
7
8
9
2
1
3
4
top cover
start switch
1
1
1
urgent stop 1
timer relay
Qty
Descviption
6
5
7
8
body
foot wheel
1
3
1
1
9
joint
1
handle
pulling board
3
Description
User Manual
www.AvantcoEquipment.com 7
CENTER AXLE
Figure 2
4
NOTES
Be sure that the keys are inserted
for each gear.
Check oil seal (15), if serious oil le-
aks from drip cup.
2
1
3
4
5
6
7
8
9
10
11
12
Center axle roundlet board
Up board
Center axle ring
Gigh-speed passive copper
1
2
1
1
1
1
1
Center axle 1
Mid-speed passive gear 1
Gasket 1
1
Gear ring 1
Engager
Small join
Qty
Descviption
Small join gasket
High-speed passive gear
13
14 1
1
Oil seal 60*90*10
Bearing 6210
15
16 1
1
Ring for cente axler
17
18
Mid-speed passive gear copper
1
1
Key 12*8*60
19
20 3
1
Ring for axle 42*1.5
Nut M4
21
22 5
5
Roller
Roller withstand
23 5
24
25 1
3
Screw M4*30
Bearing 6207
26
27 1
1
Spring gasket 24
Nut M24
Oil seal 50*80*10
Spring 8*1*18
9
Qty
1
1
1
1
2
1
3
4
5
6
arm
gear
Descviption
Item
1
1
7
8
2
2
1
2
9
10
11
12
board
screw
1
1
1
1
13
14
15
16
handwheel
handle๎axle
1
17
safefy๎covering๎switch
fluctuate๎safety๎switch
1
1
18
19
1
20
AC๎contact๎device
1
21
1
22
13
10 11
12
1
14
15
16
17 18
19
20 21
3
2
6
4
5
7
8
9
AC๎contact๎device
timer๎๎relay
22
1
key
key
gear
nut
key
thread๎bar
bearing
nut
ring
reactor
arm๎lead๎pole
2
Description
User Manual
8 www.AvantcoEquipment.com
GEAR AXLE
Figure 3
5
2
1
3
4
5
6
7
8
9
10
Axle
Bearing 80207
Gear
1
2
1
1
1
Sleeve 1
Sleeve 1
Gear 1
1
Sleeve 1
Gear
Gear
Sleeve
Qty
Descviption
1
2
3
4
5
7
6
8
10
2
9
NOTES
Be sure that the keys are inserted
for each gear.
8
11
12
11
12
11
12 2
2
Gasket
Screw M10*20
2
1
3
4
5
6
7
Screw
Speed block
Stop ring
4
1
4
1
O ring 1
O ring 1
Steel ball 4
Qty
Descviption
Spring
8
9
10
Eccentricity knot 1
Speed shaft 1
Pin 1
Description
User Manual
www.AvantcoEquipment.com 9
MOTOR
Figure 4
6
2
1
3
4
motor
oil seal
1
1
1
spiral 1
stop ring
Qty
Descviption
1
2
3
4
NOTES
If the motor does not work, first verify the
source and connection. Next, check for dama-
ged or faulty wiring or connections inside the
mixer. A noworking motor may be the result of
inappropriate voltage, broken wires, a defecti-
vecapacitor, or a defective centrifugalgovernor.
Motor damage may alsobe caused by bowl ov-
erload during mixing.
power
7
2
1
3
4
5
6
Nut
Spring gasket
Fork small axle
1
2
2
2
2
Fork axle 1
Qty
Descviption
Fork nut
Fork spring
If the motor does not work, ๎rst verify that the
power source and connection are correct. Next,
check for damaged or faulty wiring or connections
inside of the mixer. A non-functioning mixer may
be the result of inappropriate voltage, broken wires,
a defective capacitor or a defective centrifugal
governer. Motor damage may also be caused by
bowl overload during mixing.
Description
User Manual
10 www.AvantcoEquipment.com
FORK
Figure 5
6
2
1
3
4
motor
oil seal
1
1
1
spiral 1
stop ring
Qty
Descviption
1
2
3
4
NOTES
If the motor does not work, first verify the
source and connection. Next, check for dama-
ged or faulty wiring or connections inside the
mixer. A noworking motor may be the result of
inappropriate voltage, broken wires, a defecti-
vecapacitor, or a defective centrifugalgovernor.
Motor damage may alsobe caused by bowl ov-
erload during mixing.
power
7
2
1
3
4
5
6
Nut
Spring gasket
Fork small axle
1
2
2
2
2
Fork axle 1
Qty
Descviption
Fork nut
Fork spring
Description
User Manual
www.AvantcoEquipment.com 11
SPEED BLOCK
Figure 6
5
2
1
3
4
5
6
7
8
9
10
Axle
Bearing 80207
Gear
1
2
1
1
1
Sleeve 1
Sleeve 1
Gear 1
1
Sleeve 1
Gear
Gear
Sleeve
Qty
Descviption
1
2
3
4
5
7
6
8
10
2
9
NOTES
Be sure that the keys are inserted
for each gear.
8
11
12
11
12
11
12 2
2
Gasket
Screw M10*20
2
1
3
4
5
6
7
Screw
Speed block
Stop ring
4
1
4
1
O ring 1
O ring 1
Steel ball 4
Qty
Descviption
Spring
8
9
10
Eccentricity knot 1
Speed shaft 1
Pin 1
Description
User Manual
12 www.AvantcoEquipment.com
BOWL LIFTER UNIT
Figure 7
4
NOTES
Be sure that the keys are inserted
for each gear.
Check oil seal (15), if serious oil le-
aks from drip cup.
2
1
3
4
5
6
7
8
9
10
11
12
Center axle roundlet board
Up board
Center axle ring
Gigh-speed passive copper
1
2
1
1
1
1
1
Center axle 1
Mid-speed passive gear 1
Gasket 1
1
Gear ring 1
Engager
Small join
Qty
Descviption
Small join gasket
High-speed passive gear
13
14 1
1
Oil seal 60*90*10
Bearing 6210
15
16 1
1
Ring for cente axler
17
18
Mid-speed passive gear copper
1
1
Key 12*8*60
19
20 3
1
Ring for axle 42*1.5
Nut M4
21
22 5
5
Roller
Roller withstand
23 5
24
25 1
3
Screw M4*30
Bearing 6207
26
27 1
1
Spring gasket 24
Nut M24
Oil seal 50*80*10
Spring 8*1*18
9
Qty
1
1
1
1
2
1
3
4
5
6
arm
gear
Descviption
Item
1
1
7
8
2
2
1
2
9
10
11
12
board
screw
1
1
1
1
13
14
15
16
handwheel
handle๎axle
1
17
safefy๎covering๎switch
fluctuate๎safety๎switch
1
1
18
19
1
20
AC๎contact๎device
1
21
1
22
13
10 11
12
1
14
15
16
17 18
19
20 21
3
2
6
4
5
7
8
9
AC๎contact๎device
timer๎๎relay
22
1
key
key
gear
nut
key
thread๎bar
bearing
nut
ring
reactor
arm๎lead๎pole
2
Description
User Manual
www.AvantcoEquipment.com 13
TURNING PLATE AND MIXING AXLE
Figure 8
2
1
3
4
5
6
7
8
9
10
11
12
13
14
15
Inner gear
Screw
Nut
Plantaty gear
Bearing
Turning plate
Spring gasket
Nut
Bearing
1
6
1
1
1
1
1
1
1
1
1
1
1
Gasket
Oil seal
Mixing axle
1
Spring gasket 1
3
4
5
6
1
27
8
9
11
12
13
10
14
15
Pin
Key
10
Qty
Descviption
16
16 1
Safety net
1
23
4
5
6
7
8
9
2
1
3
4
top cover
start switch
1
1
1
urgent stop 1
timer relay
Qty
Descviption
6
5
7
8
body
foot wheel
1
3
1
1
9
joint
1
handle
pulling board
3
Description
User Manual
14 www.AvantcoEquipment.com
ELECTROMOTION TYPE BOWL LIFTER UNIT
Figure 9
2
Before using, please check power supply if it match
your machine and be sure ground wire is eliable.
Before testing, please take mixing device off first, in
order to avoid damage machine which is match mo-
ving direction. It's necessary to change the three-ph-
ase machine if the moving direction is not match wi-
th arrow.
Mixing: according to the different mixing-material.
Choose the different mixing devices and speed.
3
2
1
For changing the speed: Please stop machine first
before change speed in order to aviod damage gear
box.
OFF
3: Be suitable for mix and stir butter, eggs, and work wi-
th in high speed, working time is less than 15 minutes.
2. Be suitable for mix and stir stuffing and raw material,
and work in middle speed, working time is less than 20
minutes.
1: middle position is suitable for mixing dough,
working time is less than 20 minutes. Flour wat-
er quantity is 40%-50%.
380V
11
2
1
3
4
5
6
7
8
9
10
11
12
Screw M6*16
Spring gasket 6
Bearing 6004
Gear
2
4
1
2
1
1
1
Screw M6*25 2
4
2
2
Gasket 2
Lift big belt wheel
Bearing cover
Qty
Descviption
Motor transmission axle
Key 5*12
13
14 1
1
Stop ring 18
Lift gear box
15
16 1
1
Nut M12
17
18
1
1
19
20 1
1
Lift big taper gear
Key 8*12
21
22 1
1
Gear
23 1
24
25 1
1
Oil seal 30*45*10
26
27 1
1
Key 6*25
Oil cover
Lift gear box cover
Screw M4*14
Spring gasket 12
Gasket
Gear gasket
Bearing 6005
Lift small taper gear
Ring
28 1
29
30 1
1
Key 6*28
31
32 1
1
Lift motor
Lift wheel axle
Lift motor belt wheel
31
32
Lift thread bar
33
33
34
33
34 1
2
Urgent switch
Switch
Description
User Manual
www.AvantcoEquipment.com 15
THREE PHASE MOTOR DIAGRAM
Figure 9
1
The machine must be put in the dry and flat ground, and make sure the
machine steadily.
We can use four screws to fix the bracket, so the mixer will not shake or
slope.
Check the power voltage is suitable for voltage of this mixer or not befo-
re using, the ground wire is firm whether or not.
When the motor of this machine is equipped with 380V, you can ask the
professional electricians to fix the electrical source. If you find that run-
ning direction is not right, you can change the two wires, besides the gr-
ound wire.
Warning: users must install the shell ground wire.
Bowl cubage Rated voltage
Rated input power
(dm )
3(r/min) (V) (W)
60 98/186/391 3-220~ 2300
Mixing speed
2
1
3
4
Mixing device I
Bowl
1
1
1
1
123
4
Mixing device II
Mixing device III
Descviption
Qty
12
380V Electric๎diagram
SB1
SB2
SK1 30S timer
SK2 30M timer
SQP proximity switch
SQ1 safety switch
urgent stop switch
start switch
SB3 inching switch
SB4 bowl stop switch
SB5 bowl rise switch
SB6 bowl drop switch
K1 relay
protect
SQ2
FR relay
KM3 bowl rise AC contact device
KM4
K reactor
M1 motor
bowl up position switch
SQ3 bowl down position switch
KM1 mixer reduction voltage AC contact device
KM2 mixer running AC contact device
bowl drop AC contact device
M2 lift motor
M1 M2
PE R S T
KM1 KM2 KM3 KM4
K KK
FR
SB1 SB2
SQ112
SQP
K1
SK1
SK2
KM1
KM2SK1
SK1
K1SQ2
SK2
SB3
SQ2
SQ3
KM3
KM4
SB6
SB5
SB5
SB6
KM4
SB4
KM3
FR
SB3
1
The machine must be put in the dry and flat ground, and make sure the
machine steadily.
We can use four screws to fix the bracket, so the mixer will not shake or
slope.
Check the power voltage is suitable for voltage of this mixer or not befo-
re using, the ground wire is firm whether or not.
When the motor of this machine is equipped with 380V, you can ask the
professional electricians to fix the electrical source. If you find that run-
ning direction is not right, you can change the two wires, besides the gr-
ound wire.
Warning: users must install the shell ground wire.
Bowl cubage Rated voltage
Rated input power
(dm )
3(r/min) (V) (W)
60 98/186/391 3-220~ 2300
Mixing speed
2
1
3
4
Mixing device I
Bowl
1
1
1
1
123
4
Mixing device II
Mixing device III
Descviption
Qty
12
380V Electric๎diagram
SB1
SB2
SK1 30S timer
SK2 30M timer
SQP proximity switch
SQ1 safety switch
urgent stop switch
start switch
SB3 inching switch
SB4 bowl stop switch
SB5 bowl rise switch
SB6 bowl drop switch
K1 relay
protect
SQ2
FR relay
KM3 bowl rise AC contact device
KM4
K reactor
M1 motor
bowl up position switch
SQ3 bowl down position switch
KM1 mixer reduction voltage AC contact device
KM2 mixer running AC contact device
bowl drop AC contact device
M2 lift motor
M1 M2
PE R S T
KM1 KM2 KM3 KM4
K KK
FR
SB1 SB2
SQ112
SQP
K1
SK1
SK2
KM1
KM2SK1
SK1
K1SQ2
SK2
SB3
SQ2
SQ3
KM3
KM4
SB6
SB5
SB5
SB6
KM4
SB4
KM3
FR
SB3
177MX60
SPECIFICATIONS
Type MX60
Capacity 60 QT.
Power Supply 240V
Phase 3
Input Power 1750W
Hertz 60 Hz
Horsepower 2 1/2 HP
Max. Flour Capacity 50 LB.
User Manual
16 www.AvantcoEquipment.com
Troubleshooting
Trouble Possible Causes Solution
The axles canโt work when
operating the machine
Poor contact of the electrical
equipment
Check the Plug
The mixing bowl is out of position Moving direction is not correct
Change
Leaks oil Sealing washer is damaged Change
Difficult to move the bowl up and down Slideway is rusted Clean the slideway and lubricate
The motor is overheated
and speed is down
The voltage is not enough, or
incorrect speed
Check the voltage or use
lower speed
Noise and overheating Poor lubrication Add or change lubrication
Mixer touches bowl The mixing device or bowl de-
formed
Repair or change the bowl
or mixing device
Cleaning
WARNING: DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE CLEANING
!
All new mixer bowls and accessories including whips, beaters, and dough hooks should be properly washed before use.
Wash with hot water and a mild soap solution and then rinse off with either a mild vinegar or soda solution and then rinse
again with clean water. It is highly recommended this cleaning procedure is followed for bowls and accessories prior to
whipping egg whites or whole eggs. The mixer should be cleaned daily with a clean damp cloth.
If the unit has not been used for some time, it is recommended that the procedure above is followed before mixer use.
It is important that the rear bowl lift guides are greased every three months to prevent corrosion.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Avantco MX60 is a 60-quart commercial mixer designed for heavy-duty mixing tasks in bakeries, restaurants, and commercial kitchens. It features three speeds for different mixing requirements, a powerful motor for efficient operation, and a sturdy construction for durability. The mixer comes with a dough hook, a flat beater, and a wire whip for versatile mixing options. It also includes a bowl and a spatula for easy ingredient handling.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Galaxy Equipment 177GMIX30 User manual
-
VEVOR B30BT User manual
-
GGM Gastro RTK7 User manual
-
LINKRICH 3PRMI2000 User manual
-
Hobart HL400 Technical Manual
-
Hobart HL200 User manual
-
Metos SP-502A-B Owner's manual
-
Centaur MAC30 User manual
-
Globe SP40P User manual
-
Globe Food Equipment SP80PL Installation guide
