ProLights LED Fresnel User manual

Brand: ProLights

Model: LED Fresnel

Category: Stroboscopes & disco lights

Type: User manual

ProLights LED Fresnel is a compact, lightweight LED Fresnel fixture with a wide range of features, making it suitable for various applications. It provides smooth and even illumination with variable beam angle and adjustable focus, allowing precise control over the shape and size of the projected light. The device has built-in effects and color temperature adjustment, enabling dynamic and versatile lighting effects. It can be controlled via DMX or the onboard control panel, providing flexibility in operation.

USER MANUAL

MANUALE UTENTE

ECLFR2KTU-DY

EN - IT

FRESNEL PROJECTOR

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.01-05/19

ECLFR2KTU-DY

Packing content

• ECLFR2KTU-DY

• ECLFR2KTPG

• ECLFR2KBD

• ECLFRSPG

• Power cable

• User manual

TABLE OF CONTENTS

Safety

General instructionsGeneral instructions

Warnings and installation precautionsWarnings and installation precautions

1 Technical drawing

1. 1 Operating elements and connections1. 1 Operating elements and connections

2 Installation

2. 1 Mounting2. 1 Mounting

3 Functions and settings

3. 1 Operation3. 1 Operation

3. 2 Basic3. 2 Basic

3. 3 Menu structure3. 3 Menu structure

3. 4 DMX addressing3. 4 DMX addressing

3. 5 DMX conguration3. 5 DMX conguration

3. 6 Linking3. 6 Linking

3. 7 Screen3. 7 Screen

3. 8 Fixture settings3. 8 Fixture settings

3. 9 Information3. 9 Information

3. 10 Master/Slave mode3. 10 Master/Slave mode

3. 11 Eects mode3. 11 Eects mode

3. 12 Static mode3. 12 Static mode

3. 13 DMX control3. 13 DMX control

3. 14 Connection of the DMX line3. 14 Connection of the DMX line

3. 15 Construction of the DMX termination3. 15 Construction of the DMX termination

4 Maintenance

4. 1 Maintenance and cleaning the unit4. 1 Maintenance and cleaning the unit

4. 2 Trouble shooting4. 2 Trouble shooting

ECLFR2KTU-DY

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bumps;

- in places with a temperature of over 45 °C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

ECLFR2KTU-DY

- 1 - TECHNICAL DRAWING

Technical drawing Fig.1

455

421

537

Fig.2

ECLFR2KTU-DY

1.1 OPERATING ELEMENTS AND CONNECTIONS

1. VENTILATION GRID for air ow outlet not to

be obstructed.

2. Knob for inclination adjustment.

3. HANDLE

4. MOUNTING BRACKET

5. SPIGOT

6. CONTROL PANEL with display and 1 button

used to access the control panel functions

and manage them.

7. ZOOM ADJUSTMENT Knob AND FOCUS to

zoom the projected image clearly.

8. GEL FILTER FRAME

9. BARN DOOR with directional aps to adjust

the light beam.

10. GUIDE for locking and releasing accessories

11. MAIN FUSE HOLDER: replace a burnt-out fuse by

one of the same type only

12. POWER IN (PowerCON TRUE IN): for connection

to a socket (100-240V~/50-60Hz) via the supplied

mains cable.

13. DMX IN (5-pole XLR): 1 = ground, 2 = DMX-, 3 =

DMX+, 4 N/C, 5 N/C.

14. DMX OUT (5-pole XLR): 1 = ground, 2 = DMX-, 3 =

DMX+, 4 N/C, 5 N/C.

15. POWER OUT (PowerCON TRUE OUT): power

output for connection of multiple units in series.

Fig.4

CLAMP

ECLFR2KTU-DY

- 2 - INSTALLATION

2.1 MOUNTING

ECLFR2KTU-DY is designed for applications in exhibition areas, commercial spaces, museums, restaurant,

churches, and any other installation where size is an important factor. For xing, stable mounting clips are

required. The mounting place must be of sucient stability and be able to support a weight of 10 times

of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the xture’s being used.

• Install the projector at a suitable location.

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm. The

adjust the projector and use the knobs.

NOTE - For the installation of the ECLFR2KTU-DY make sure that the ridge of the adaptor is in with the

groove of the track. Turn knobs 90° to connect the adaptor to the circuit. Please see the gure 4.

Fig.5

ECLFR2KTU-DY

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

To turn ECLFR2KTU-DY connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then the unit

is ready for operation and can be operated via a DMX controller. To switch o, disconnect the mains plug

from the socket. For a more convenient operation it is recommended to connect the unit to a socket which

can be switched on and o via a light switch.

3.2 BASIC

The ECLFR2KTU-DY has a display and 1 button for access to the control panel functions (g.5).

Knob

Used to access the menu, to return a previous

menu option, to navigate through the menu,

to select and store the current menu or conrm

the current function value or option within a

1 CONNECT

DMX Address

Value (001-512)

DMX Mode

EASY 1CH

BASIC 2CH 1

BASIC 2CH 2

BASIC 3CH

STANDARD 5CH

2 SETUP

Screen

Back Light

10S

20S

30S

Flip Display

No-Yes

3 ADVANCED

Dimmer Mode

O

Dimmer 1

Dimmer 2

Dimmer 3

Led Frequency

600Hz

1200 Hz

2000 Hz

4000 Hz

6000Hz

25kHZ

Fan Mode

Auto

O

Silent

Factory Reload

No-Yes

4 INFORMATION

Fixture Hours

0-9999

Version

V1.0

UID

15D0022A****

5 STAND ALONE

Master/Slave

Eects

Eect 1

Speed 1~100

Eect 2

Eect 3

Eect 4

Static

Dimmer

Value ( 0~255)

Strobe

ECLFR2KTU-DY

3.3 MENU STRUCTURE

ECLFR2KTU-DY

3.4 DMX ADDRESSING

To set DMX addressing follow the instructions below:

• Press the knob to enter the menu mode.

• Use the knob to select Connect. Press the knob to conrm.

• Rotate the knob to select DMX Address. Press the knob to conrm.

• Rotate the knob to select the desired value 001-512. Press the knob to conrm.

• Press repeatedly the knob to return the menu mode.

To able to operate the ECLFR2KTU-DY with a light controller, adjust the DMX start address for the rst a

DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX

channel, adjust the start address 33 on the ECLFR2KTU-DY. The other functions of the light eect panel are

then automatically assigned to the following addresses.

3.5 DMX CONFIGURATION

The ECLFR2KTU-DY has dierent DMX channels congurations available selectable through the control

panel.

• Rotate the knob to enter the menu mode.

• Use the knob to select the Connect. Press the knob to conrm.

• Press the knob to select the DMX mode. Then press the knob to conrm.

• Press the knob to select the desired conguration (EASY 1CH - BASIC 2CH 1 - BASIC 2CH 2 - BASIC3CH - STANDARD

5CH); then press it to save.

• Press repeatedly the knob to return the menu mode.

The tables on page 12 indicate the operating mode and DMX value. The ECLFR2KTU-DY is equipped with

5-pole XLR connections.

3.6 LINKING

Several units may be interconnected; follow the instructions below:

1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the

units. For longer cable runs we suggest a terminator at the last xture (see page 13).

Numero

canali DMX

Indirizzo di

start (esempio)

Indirizzo DMX

occupati

Prossimo indirizzo di start

possibile per unità n°1

Prossimo indirizzo di start

possibile per unità n°2

Prossimo indirizzo di start

possibile per unità n°3

1 33 33 34 35 36

2 33 33-34 35 37 39

3 33 33-35 36 39 42

5 33 33 - 37 38 43 48

. . . . . . . . . . . .

DMX Address: 33 DMX Address: 42DMX Address: 36 DMX Address: 39

Fig.5 - Example 3 DMX channels conguration

. . . . . . . . . . . .

DMX512 Controller

ECLFR2KTU-DY

3.7 SCREEN

It is possible to modify the following parameters, related to the display, following the same procedure:

• Press the knob to access the main menu.

• Rotate the knob to scroll through the menu, select Set Up, then press the knob access the next menu.

• Press the knob to select Screen and press the knob to proceed.

• Select the proposed option with the knob and press the knob to conrm.

- Backlight - Auto O display backlight. This function allows you to switch o automatically the back-

lighting of the display after a certain time which can be set using the directional keys. To have the

display always on select On or set a value between those shown (10s, 20s, 30s) to turn o the display

once the chosen time has elapsed, after exiting the menu.

- Flip Display - Display orientation. This feature allows you to rotate the display by 180 ° to get a better

view of the display when the unit is hanging upside down. Select Yes to activate the function, No to

deactivate it.

• Press the knob to conrm the selection.

• Press the knob repeatedly to exit the menu and to save the changes made.

3.8 ADVANCED

You can change the parameters for the device by following these steps:

• Press the knob to enter the menu mode.

• Use the knob to select the Advanced. Press the button knob.

• Press the knob to select the desired option and press the Knob to conrm:

- Dimmer Mode - Adjusting the dimmer. Enter in Dimmer Mode to select specic dimming curve.

Particularly when set:

• O: The increase in light intensity is linear.

• Dimmer 1: dimmer curve with low fade.

• Dimmer 2: dimmer curve with medium fade.

• Dimmer 3: dimmer curve with high fade.

- LED Frequency - To adjust the frequency of the LEDs. Select the frequency 600 Hz - 25 KHz using the knob

and press it to conrm the selection.

ECLFR2KTU-DY

- Fan Mode - Fan Speed. Select the fan speed (Auto, On, O, Silent) using the knob.

- Factory Reload - To reset the unit. Select Yes or No and select the knob to conrm.

• Press repeatedly the knob to return the menu mode.

3.9 INFORMATION

To view all the information on the device, proceed as follows:

• Press the knob to access the main menu. Rotate the knob to select Information, then press it to access

the next menu.

• Rotate the knob to scroll through the menu, then select one of the following informationa nd press it

to display it.

- Fixture Time - To view the operating time of the projector.

- Software Version - To view the rmware version will show on the display.

- UID - To view the identication ID for the RDM control.

• Press repeatedly the knob to return the menu mode.

3.10 MASTER/SLAVE MODE

This mode will allow you to link up the units together without a controller. Choose a unit to function as the

Master. The unit must be the rst unit in line; other units will work as slave.

• Press the knob so many times until the display shows Stand Alone, then press it.

• Select Master/Slave.

• Using knob, select the desired mode and then press the Knob.

• Press the knob to go back or to meet the waiting time to exit the setup menu.

• Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the

units. For longer cable runs we suggest a terminator at the last xture (see page 13).

• Set the slaves to the same DMX modes.

NOTE: the unit, set in Static or Eect mode, always appears to be Master.

3.11 EFFECTS MODE

This xture has a built-in automatic program. To access this, please see the below instructions:

• To enter the Eects mode, press the knob to access the menu.

• Rotate the knob select Stand Alone, then select Eect. Press it to conrm

• Use the knob to select the desired program Eect 1, Eect 2, Eect 3, Eect 4, then press it to conrm.

• Set the value (1 - 100), then press the knob to conrm.

NOTE: after selecting the described mode, the unit will be Master.

3.12 STATIC MODE

This xture has the ability to accept custom static color settings. Access these chases via the control panel

on the back of the xture.

• To enable the static mode, press the knob repeatedly until Stand Alone shows on the display.

• Set the strobo value Strobe (000 - 255), through the knob, then press it to conrm.

• Set the dimmer value Dimmer (000 - 255), through the knob, then press it to conrm.

• Press repeatedly the knob to return the menu mode.

NOTE: after selecting the described mode, the unit will be Master.

1 CHANNEL

MODE

FUNCTION DMX

Value

1 Ch

DIMMER

0~100% 000 - 255

2 CHANNELS 2

MODE

FUNCTION DMX

Value

2 Ch

DIMMER

0~100% 000 - 255

STROBE

NO Function

Strobe Slow to Fast

000 - 010

011 - 255

3 CHANNELS

MODE

FUNCTION DMX

Value

3 Ch

DIMMER

0~100% 000 - 255

DIMMER FINE

0~100% 000 - 255

STROBE

NO Function

Strobe Slow to Fast

000 - 010

011 - 255

5 CHANNELS

MODE

FUNCTION DMX

Value

5 Ch

DIMMER

0~100% 000 - 255

STROBE

NO Function

Strobe Slow to Fast

000 - 010

011 - 255

AUTO PROGRAMS

No Function

Auto Program 1

Auto Program 2

Auto Program 3

Auto Program 4

000 - 010

011 - 070

071 - 130

131 - 190

191 - 255

AUTO SPEED

Auto speed slow to fast 000 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

2 CHANNELS 1

MODE

FUNCTION DMX

Value

2 Ch

DIMMER

0~100% 000 - 255

DIMMER FINE

0~100% 000 - 255

ECLFR2KTU-DY

3.13 DMX CONTROL

ECLFR2KTU-DY

Fig.6

Fig.7

3.14 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.15 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

Example:

5 pin XLR connector

ECLFR2KTU-DY

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch o the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

4.2 TROUBLESHOOTING

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• Faulty LED

• Check the power supply voltage

• Increase the value of the dimmer channels

• Replace the LED board

General low light intensity

• Dirty lens assembly

• Misaligned lens assembly

• Clean the xture regularly

• Install lens assembly properly

Fixture does not power up

• No power

• Loose or damaged power cord

• Check for power on power outlet

• Check power cord

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

REV.01-05/19

Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.

La riproduzione - anche parziale - per propri scopi commerciali è vietata.

Al ne di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modicare, in

qualunque momento e senza preavviso, le speciche menzionate nel presente manuale di istruzioni.

Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it

ECLFR2KTU-DY

• ECLFR2KTU-DY

• ECLFR2KTPG

• ECLFR2KBD

• ECLFRSPG

• Cavo di alimentazione

• Manuale utente

Contenuto dell'imballo:

INDICE

Sicurezza

Avvertenze generaliAvvertenze generali

Attenzioni e precauzioni per l’installazioneAttenzioni e precauzioni per l’installazione

1 Disegno tecnico

1. 1 Elementi di comando e di collegamento 1. 1 Elementi di comando e di collegamento

2 Installazione

2. 1 Montaggio2. 1 Montaggio

3 Funzioni e impostazioni

3. 1 Funzionamento3. 1 Funzionamento

3. 2 Impostazione base3. 2 Impostazione base

3. 3 Struttura menù3. 3 Struttura menù

3. 4 Modalità DMX3. 4 Modalità DMX

3. 5 Congurazione canali DMX3. 5 Congurazione canali DMX

3. 6 Collegamento3. 6 Collegamento

3. 7 Screen3. 7 Screen

3. 8 Advanced3. 8 Advanced

3. 9 Informazioni sul dispositivo3. 9 Informazioni sul dispositivo

3. 10 Modalità Master/Slave3. 10 Modalità Master/Slave

3. 11 Modalità Eects3. 11 Modalità Eects

3. 12 Modalità Static3. 12 Modalità Static

3. 13 Canali DMX3. 13 Canali DMX

3. 14 Collegamenti della linea DMX3. 14 Collegamenti della linea DMX

3. 15 Costruzione del terminatore DMX3. 15 Costruzione del terminatore DMX

4 Manutenzione

4. 1 Manutenzione e pulizia del sistema ottico4. 1 Manutenzione e pulizia del sistema ottico

4. 2 Risoluzione dei problemi4. 2 Risoluzione dei problemi

ECLFR2KTU-DY

ATTENZIONE! Prima di effettuare qualsiasi operazione con l’unità, leggere con attenzione

questo manuale e conservarlo accuratamente per riferimenti futuri. Contiene informazioni

importanti riguardo l’installazione, l’uso e la manutenzione dell’unità.

SICUREZZA

Avvertenze generali

• I prodotti a cui questo manuale si riferisce sono conformi alle Direttive della Comunità Europea e per-

tanto recano la sigla .

• Il dispositivo funziona con pericolosa tensione di rete 230V~. Non intervenire mai al suo interno al di

fuori delle operazioni descritte nel presente manuale; esiste il pericolo di una scarica elettrica.

• È obbligatorio eettuare il collegamento ad un impianto di alimentazione dotato di un’eciente messa

a terra (apparecchio di Classe I secondo norma EN 60598-1). Si raccomanda, inoltre, di proteggere le

linee di alimentazione delle unità dai contatti indiretti e/o cortocircuiti verso massa tramite l’uso di

interruttori dierenziali opportunamente dimensionati.

• Le operazioni di collegamento alla rete di distribuzione dell’energia elettrica devono essere eettuate

da un installatore elettrico qualicato. Vericare che frequenza e tensione della rete corrispondono alla

frequenza ed alla tensione per cui l’unità è predisposta, indicate sulla targhetta dei dati elettrici.

• L’unità non per uso domestico, solo per uso professionale.

• Evitare di utilizzare l’unità:

- in luoghi soggetti a vibrazioni, o a possibili urti;

- in luoghi a temperatura superiore ai 45°C.

• Evitare che nell’unità penetrino liquidi inammabili, acqua o oggetti metallici.

• Non smontare e non apportare modiche all’unità.

• Tutti gli interventi devono essere sempre e solo eettuati da personale tecnico qualicato. Rivolgersi al

più vicino centro di assistenza tecnica autorizzato.

• Se si desidera eliminare il dispositivo denitivamente, consegnarlo

per lo smaltimento ad un’istituzione locale per il riciclaggio.

Attenzioni e precauzioni per l’installazione

• Se il dispositivo dovesse trovarsi ad operare in condizioni dierenti da quelle descritte nel presente

manuale, potrebbero vericarsi dei danni; in tal caso la garanzia verrebbe a decadere. Inoltre, ogni altra

operazione potrebbe provocare cortocircuiti, incendi, scosse elettriche, rotture etc.

• Prima di iniziare qualsiasi operazione di manutenzione o pulizia sull’unità togliere la tensione dalla rete

di alimentazione.

• È assolutamente necessario proteggere l’unità per mezzo di una fune di sicurezza. Nell’eseguire qual-

siasi intervento attenersi scrupolosamente a tutte le normative (in materia di sicurezza) vigenti nel

paese di utilizzo.

• Installare l’unità in un luogo ben ventilato.

• Mantenere i materiali inammabili ad una distanza di sicurezza dall’unità.

• I ltri, le lenti o gli schermi ultravioletti se danneggiati possono limitare la loro ecienza.

• I LED devono essere sostituiti se danneggiati o termicamente deformati.

• Non guardare direttamente il fascio luminoso. Tenete presente che i veloci cambi di luce possono pro-

vocare attacchi d’epilessia presso persone fotosensibili o epilettiche.

• Non toccare l’alloggiamento del prodotto quando è in funzione perché potrebbe essere molto caldo.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

ECLFR2KTU-DY

- 1 - DISEGNO TECNICO

Disegno tecnico Fig.1

455

421

537

Fig.3Pannello posteriore

1. GRIGLIA DI VENTILAZIONE per uscita usso

d'aria da non ostruire.

2. MANOPOLA per regolazione inclinazione.

3. MANIGLIE

4. STAFFA DI MONTAGGIO

5. SPIGOT

6. PANNELLO DI CONTROLLO con display e 1

pulsante per accesso e gestione delle funzioni.

7. MANOPOLA DI REGOLAZIONE ZOOM E

MESSA A FUOCO per zoommare l'immagine

proiettata in modo chiaro.

8. TELAIO PORTA GELATINA

9. ALETTE per regolazione fascio di luce.

1.2 ELEMENTI DI COMANDO E COLLEGAMENTI

10. GUIDA per bloccaggio e rilascio accessori.

11. PORTAFUSIBILE: sostituire un fusibile difettoso

solo con uno dello stesso tipo.

12. POWER IN (PowerCON TRUE IN): per il

collegamento ad una presa di rete (100-240V~/50-

60Hz) tramite il cavo rete in dotazione.

13. DMX IN (XLR a 5 poli): 1= massa, 2 = DMX -, 3 =

DMX +, 4 N/C, 5 N/C.

14. DMX OUT (XLR a 5 poli): 1 = massa, 2 = DMX -, 3 =

DMX +, 4 N/C, 5 N/C.

15. POWER OUT (PowerCON TRUE OUT): output

alimentazione per connessione di più unità in

serie.

ECLFR2KTU-DY

Page is loading ...

ProLights LED Fresnel User manual

Brand: ProLights

Model: LED Fresnel

Category: Stroboscopes & disco lights

Type: User manual

Download PDF

report

in other languages

italiano: ProLights LED Fresnel Manuale utente

ProLights LED Fresnel User manual

ProLights LED Fresnel User manual

in other languages

Related papers

Other documents