ProLights SOLAR27Q User manual

Brand: ProLights

Model: SOLAR27Q

Category: Stroboscopes & disco lights

Type: User manual

USER MANUAL

MANUALE UTENTE

SOLAR27Q

OUTDOOR COMPACT WASHLIGHT

EN - IT

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the characteris-

tics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.002-12/18

SOLAR27Q

Packing content

• SOLAR27Q

• S27QFILTER60

• Power cable

• User manual

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 Linking

3. 5 DMX addressing conguration

3. 6 DMX mode conguration

3. 7 DMX addressing

3. 8 Wireless

3. 9 Screen

3. 10 Dimmer mode

3. 11 White balance

3. 12 LED Frequency

3. 13 Factory reload

3. 14 Information

3. 15 Master/Slave

3. 16 Eect

3. 17 Static

3. 18 Manual

3. 19 Connection of the DMX line

3. 20 Construction of the DMX termination

3. 21 DMX control

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Trouble shooting

SOLAR27Q

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bumps;

- in places with an ambient temperature of over 50°C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• The minimum distance between the xture and surrounding walls must be more than 50 cm and the

air vents at the housing must not be covered in any case.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• The maximum temperature that can be reached on the external surface of the tting, in a thermally

steady state, is high. After power o, please cool down over 15 minutes.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

SOLAR27Q

- 1 - INTRODUCTION

1.1 DESCRIPTION

SOLAR27Q is a compact fan-free outdoor wash light featuring an outstanding brightness of 10,832

lumens. Equipped with 27x10W RGBW full colour LEDs, delivering superior colour mixing. Featuring a

slim size as well as the multiple interchangeable optics through magnets, including asymmetrical lters

which, all together, make the SOLAR27Q an incredibly exible device for indoor use and outdoor. Whilst

highly-powerful, the SOLAR27Q also benets from being silent.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source:27x10 W CREE RGBW

• CT:5960 K

• CRI:71,8

• Luminous Flux:@FULL 10832 lm - With included lter 6987 lm

• Lux:@FULL (25°) 6133 lux - With included lter 1027 lux @3m Full

• Lux:@FULL (25°) 2208 lux - With included lter 370 lux @5m Full

• Source Life Expectancy: >50.000 h

• Other:Magnetic lter included to achieve 45° (60° lter), barndoor not included

OPTICS

• Beam angle:25° - With included lter 45 °

• Field angle:39° - With included lter 69 °

• Lens diameter:36 mm

• Lens type: honeycomb gapless plano-convex optics

• Additional optics:10° / 15° / 45° / 40° lter / 10X60° lter / 30X60° lter

COLOR SYSTEM

• Color Mixing: RGBW/FC

• CTC: CTC control through independent DMX channel

• Color Wheel: Virtual color wheel with presets

DYNAMIC EFFECTS

• Static Color Mode: Selection of static color

• Manual Color Mode: Manual adjustment of color

• Auto Mode: Built-in programs with execution speed adjustment

BODY

• Hardware On-board:Magnetic lter frame with 45° lter

• Tilt Angle:+/- 90 ° Manual

• Body: Sturdy die-cast aluminium body conceived for long-time durability

• Body Color: Black

CONTROL

• Protocols: DMX512, RDM, W-DMX

• DMX channels:5 / 7 / 10 / 13 / 17 channel

• Pixel control:3 horizontal individually select and control sections

• W-DMX: included, wireless solution receiver

• RDM: RDM ready for xture remote monitor and settings

SOLAR27Q

• Display: black OLED high resolution display

• Firmware upgrade: yes, via USB-DMX interface (UPBOX1) not included

• Master/Slave: for synchronized operation of more units linked in a chain

ELECTRONICS

• Dimmer: linear 0~100% electronic dimmer

• Dimmer curves: dierent dimming curves available

• Battery backup: battery backup for user operation without connecting to the main power

• Operating temperature: -20° ~ +50°

• Flicker: icker free frequency with adjustable PWM

• Selectable PWM: 600~25K Hz

ELECTRICAL

• Power supply: 100-240V – 50/60Hz

• Power consumption (at 230V):268 W

• Power consumption (at 120V):275 W

• Output (at 230V):9 units on a single power line

• Output (at 120V):5 units on a single power line

• Power factor:0,994

PHYSICAL

• Cooling: natural cooling of the peculiar chassis and to absence of fans

• Sospension and xing: hanging bracket for oor positioning with “Quick-Lock” system

• Signal connection: Seetronic XLR 5p IN/OUT connectors

• Data connection: W-DMX OEM TRX

• Power connection: Seetronic powerCON waterproof IN/OUT connectors

• IP rating:65 for temporary outdoor application, not for xed installation

• Dimensions (WxHxD):454x153x268.5 mm

• Weight:9 kg

Technical drawing

Fig.1

454mm/17,87in

83mm/

3,26in

268.5mm/11,24in

SOLAR27Q

1 32

9 9 8

4 5 6 7 1

1.3 OPERATING ELEMENTS AND CONNECTIONS

1. KNOB

2. W-DMX receiver

3. POWER IN (PowerCON TRUE IN): for connection

to a socket (100-240V/50-60Hz) via the supplied

mains cable,

4. DMX IN (5-pole XLR): 1 = massa, 2 = DMX -, 3 =

DMX +, 4 N/C, 5 N/C.

5. CONTROL PANEL with display and 4 touch but-

tons used to access the control panel functions

and manage them.

6. DMX OUT (5-pole XLR): 1 = ground, 2 = DMX-, 3

= DMX+, 4 N/C, 5 N/C.

7. POWER OUT: connect to supply power to the

next unit.

8. HOLE for safety cable passage

9. HOLE for quick-lock omega bracket

Fig.2

SOLAR27Q

- 2 - INSTALLATION

2.1 MOUNTING

The SOLAR27Q may be set up on a solid and even surface. By means of the xing facilities of the baseplate,

the unit can also be mounted upside down to a cross arm. The base plate is shown in g.3. For xing, stable

mounting clips are required. According to the gure, the bolts of the brackets are placed into the openings

provided in the base plate and turned clockwise until they lock (to the stop). Always ensure that the unit

is rmly xed to avoid vibration and slipping while operating. The mounting place must be of sucient

stability and be able to support a weight of 10 times of the unit’s weight. When carrying out any installa-

tion, always comply scrupulously with all the regulations (particularly regarding safety) currently in force

in the country in which the xture’s being used. Always additionally secure the projector with the safety

rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the maximum

fall of the projector will be 20 cm.

Fig.3

OMEGA

QUICK-LOCK

SAFETY

CABLE

SAFETY

CABLE

CLAMP

SOLAR27Q

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). The unit will run built-in program to

reset all motors to their home position. Shortly after that the SOLAR27Q is ready for operation. To switch

o, disconnect the mains plug from the socket. For a more convenient operation it is recommended to

connect the unit to a socket which can be switched on and o via light switch.

3.2 BASIC

The control panel of SOLAR27Q has a display and 4 buttons for the complete programming and manage-

ment of the projector menu (g.4).

MENU UP DOWN ENTER

Used to access the menu or to

return a previous menu option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in a

function

Used to select and store the

current menu or conrm the

current function value or option

within a menu

Fig.4 - Functions of the buttons and display icons

Down

Mode

Enter

SOLAR27Q

3.3 MENU STRUCTURE

1 CONNECT

DMX Address

1-512

DMX Mode

5CH

7CH

10CH

13CH

17CH

Wireless

Receive On/O

Receive Reset

On/O

No/Yes

Wireless on DMX

No/Yes

2 SET UP

Screen

Backlight

Key Lock

On/10s/20s/30s

No/Yes

3 ADVANCED

Dimmer Mode

O/Dimmer1/2/3

White Balance

O

Adjust

Red

Green

Blue

White

<125-255>

LED Frequency

600Hz/1200Hz/2000Hz/4000Hz/6000Hz/25kHz

Factory Reload

No/Yes

4 INFORMATION

Fixture Time

Version

UID

0-9999

V1.0

<15D00220****>

5 STAND ALONE

Master/Slave

Master

Slave

Eects

Eect1

…

Eect9

Speed 1-100

Static

Fixed Color

RGB

RGW

RBW

GBW

RGBW

Manual color

Red

Green

Blue

White

<000-255>

SOLAR27Q

3.4 LINKING

Multiple units can be connected so that all secondary units have the same lighting eect as the main unit

(Master).

1. Connect the DMX OUT output of the main unit to the DMX IN input of the rst secondary unit using a

5 pole XLR cable.

2. Connect the DMX OUT output of the rst secondary unit with the DMX IN input of the second second-

ary unit, etc.

3.5 DMX ADDRESSING CONFIGURATION

To enter the DMX mode proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Connect icon, then press the ENTER

button to access the next DMX Address.

• Use the arrow buttons to set the desired value (001-512). Press the ENTER button to conrm.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

3.6 DMX MODE CONFIGURATION

SOLAR27Q has 5 DMX channel congurations that can be accessed from the control panel.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Connect icon, then press the ENTER

button to enter the next menu.

• Press the UP/DOWN button to select DMX Mode.

• Use the UP/DOWN button to select the desired DMX channel conguration (5CH, 7CH, 10CH, 13CH, 17CH),

then press the ENTER button to conrm the selection.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

The tables on page 14, 15 and 16 indicate the operating modes and related DMX values. As an interface

DMX, the unit has 5-pin XLR contacts.

3.7 DMX ADDRESSING

For operation via a light control unit with DMX512 protocol, simply connect SOLAR27Q to the controller.

The projector has a DMX channel conguration that can be accessed from the control panel. In order to

control SOLAR27Q with a light control unit, the DMX start address must be set for the rst DMX channel.

If, for example, the address 33 is provided on the control unit to control the function of the rst DMX chan-

nel, the start address 33 must be set on the SOLAR27Q. The other panel functions will be automatically

assigned to the following addresses.

Number of

DMX chan-

nels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

5 33 33-37 38 43 48

7 33 33-39 40 47 54

10 33 33-42 43 53 63

13 33 33-45 46 59 72

17 33 33-49 50 67 84

SOLAR27Q

3.8 WIRELESS

To change the wireless control settings, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Connect icon, then press the ENTER

button to enter the next menu.

• Press the UP/DOWN button to select Wireless and press the ENTER button to proceed.

• Select the proposed option with the UP/DOWN button and press the ENTER button to conrm your

choice.

3. Receive On/O - Disables/enables the DMX signal via cable. Select OFF to deactivate the function or ON

to activate the function.

4. Receive Reset - Reset the unit’s wireless connection. Select NO to deactivate the function or YES to acti-

vate the function.

5. Wireless on DMX - able or disable this function if you need or not to retransmitt on DMX out of the unit the

same DMX signal received from wireless transmitter.

• Press the ENTER button to conrm the selection.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

NOTE: If the projector is in Blackout mode before synchronizing with the transmitting wireless unit, and

if the wireless signal is lost after synchronization with the transmitting unit, the projector will remain on

according to the last received DMX value.

If the projector was in STATIC or AUTO mode before synchronizing with the wireless transmitter, if the

wireless signal is lost after synchronization with the transmitting unit, the projector will return to the previ-

ously set STATIC or AUTO.

3.9 SCREEN

It is possible to modify the following parameters, related to the display, following the same procedure:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select Set Up, then press the ENTER button to

access the next menu.

• Press the UP/DOWN button to select Screen and press the ENTER button to proceed.

• Select the proposed option with the UP/DOWN button and press the ENTER button to conrm.

- Backlight - Auto O display backlight. This function allows you to switch o automatically the backlighting

of the display after a certain time which can be set using the directional keys. To have the display always

on select On or set a value (10s /20s/30s) to turn o the display once the chosen time has elapsed, after exit-

ing the menu.

- Key lock - With this function, you can lock the keys on the control panel to prevent, for example, tampering

Fig.5 - Example of a DMX 5-channel conguration

DMX Address: 53DMX Address: 43DMX Address: 38 DMX Address: 48

. . . . . . . . . . . .

DMX512 Controller

SOLAR27Q

with the settings. If this function is activated, the keys are locked automatically. To disable or temporarily

disable or disable the key lock function, press the keys in the following order to regain access to the menu

commands:

UP, DOWN, UP, DOWN, ENTER. Select YES to activate the function or NO to deactivate it.

• Press the ENTER button to conrm the selection.

• Press the MENU key repeatedly to exit the menu and to save the changes made.

3.10 DIMMER MODE

Select this function to choose to simulate dierent dimming curves.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Advanced icon, then press the ENTER

button to enter the next menu.

• Press the UP/DOWN button to select Dimmer Mode and press the ENTER button to proceed.

• Press the UP/DOWN button to scroll through the menu, then select O to deactivate or select Dimmer1/

Dimmer2 /Dimmer3. Then select ENTER to conrm.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

3.11 WHITE BALANCE

Select this function to adjust e Red, Green, Blue and White parameter to make dierent whites.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Advanced icon, then press the ENTER

button to enter the next menu.

• Press the UP/DOWN button to select White Balance and press the ENTER button to proceed.

• Press the UP/DOWN button to scroll through the menu, then select O to deactivate the balance. Select

Adjust to balance with following colors: Red, Green, Blue, White. Then select ENTER to conrm.

• Set the desired value (125-255)and press the ENTER button to conrm..

• Press the MENU button repeatedly to exit the menu and to save the changes made.

3.12 LED FREQUENCY

Select this function to adjust the frequency of LED.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Advanced icon, then press the ENTER

button to enter the next menu.

• Press the UP/DOWN button to select LED Frequency and press the ENTER button to proceed.

• Press the UP/DOWN button to select one of available setting: 600Hz, 1200Hz, 2000Hz, 4000Hz, 6000Hz25kH.

Then select ENTER to conrm.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

3.13 FACTORY RELOAD

Select this function to reset the unit to the factory settings.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Advanced icon, then press the ENTER

button to access the next menu.

• Press the UP/DOWN button to select Factory Reload and press the ENTER button to proceed.

• Press the UP/DOWN buttons to select ON or OFF, then press the ENTER button to conrm.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

3.14 INFORMATION

To view all the information on the device, proceed as follows:

• Press the ENTER button to access the main menu.

SOLAR27Q

• Press the UP/DOWN button to select Information, then press the ENTER button to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select one of the following information

and press the ENTER button to display it.

- Fixture Time - This option shows the user the amount of hours the SOLAR27Q has been in use throughout

its lifetime.

- Version - Through the Version function, the version can be viewed on the display of the installed software.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

3.15 MASTER/SLAVE MODE

This mode will allow you to link up the units together without a controller. Choose a unit to function as the

Master. The unit must be the rst unit in line; other units will work as slave.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to select Stand Alone, then press the ENTER button to enter the next menu.

• Press the UP/DOWN button to select Master/Slave and press the ENTER button to proceed.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

• Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the

units. For longer cable runs we suggest a terminator at the last xture (see page 13).

3.16 EFFECT

Select this function to choose the eect.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to select Stand Alone, then press the ENTER button to enter the next menu.

• Press the UP/DOWN button to select Eects, then press the ENTER button to enter the next menu.

• Set the eect Eect1, Eect2, Eect3, Eect4, Eect5, Eect6, Eect7, Eect8, Eect9 through the UP/DOWN but-

tons, then press ENTER.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

3.17 STATIC MODE

This xture has the ability to accept custom static color settings. Access these chases via the control panel

on the back of the xture.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to select Stand Alone, then press the ENTER button to enter the Static next

menu.

• Press the UP/DOWN button to select Fixed Color, then press the ENTER button to enter the next menu.

• Set the colors R, G, B, W, GB, RB, RG, RGB, RW, GW, BW, RGW, RBW, GBW, RGBW through the UP/DOWN buttons,

then press ENTER.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

3.18 MANUAL COLOR

This mode allows to combine the colors red, green, blue and white (Red, Green, Blue, White).

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to select Stand Alone, then press the ENTER button to enter the Static next

menu.

• Select the color Red, Green, Blue, White through the UP/DOWN buttons, then press ENTER.

• Using UP/DOWN buttons, select the desired color value 000 - 255.

• Press the MENU button repeatedly to exit the menu and to save the changes made.

SOLAR27Q

3.19 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

Fig.6

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.20 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

Fig.7

Example:

5 pin XLR connector

SOLAR27Q

3.21 DMX CONTROL

5 CHANNEL

MODE

FUNCTION DMX

Value

5 Ch

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

WHITE

0~100% 000 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000-051

052-101

102-152

153-203

204-255

10 CHANNEL

MODE

FUNCTION DMX

Value

10 Ch

DIMMER

0~100% 000 - 255

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

WHITE

0~100% 000 - 255

STROBE

No function

Strobe Slow to Fast

000 - 010

011 - 255

COLOR MACRO

No Function

R 100%, G 0~100%, B 0 %

R 100%~0 %, G 100%, B 0 %

R 0 %, G 100%, B 0~100%

R 0 %, G 100~0 %, B 100%

R 0~100%, G 0 %, B 100%

R 100%, G 0 %, B 100~0 %

R 100%, G 0~100%, B 0~100%

R 100~0 %, G 100~0 %, B 100%

R 100%, G 100%, B 100%, W 100%

2800k

3000k

3200k

4000k

5600k

6000k

6500k

7000k

8000k

9000k

10000k

000 - 010

011 - 030

031 - 050

051 - 070

071 - 090

091 - 110

111 - 130

131 - 150

151 - 170

171 - 200

201 - 205

206 - 210

211 - 215

216 - 220

221 - 225

226 - 230

231 - 235

236 - 240

241 - 245

246 - 250

251 - 255

7 CHANNEL

MODE

FUNCTION DMX

Value

7 Ch

DIMMER

0~100% 000 - 255

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

WHITE

0~100% 000 - 255

STROBE

No function

Strobe Slow to Fast

000 - 010

011 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000-051

052-101

102-152

153-203

204-255

SOLAR27Q

13 CHANNEL

MODE

FUNCTION DMX

Value

13 Ch

RED 1

0~100% 000 - 255

GREEN 1

0~100% 000 - 255

BLUE 1

0~100% 000 - 255

WHITE 1

0~100% 000 - 255

RED 2

0~100% 000 - 255

GREEN 2

0~100% 000 - 255

BLUE 2

0~100% 000 - 255

WHITE 2

0~100% 000 - 255

RED 3

0~100% 000 - 255

GREEN 3

0~100% 000 - 255

BLUE 3

0~100% 000 - 255

WHITE 3

0~100% 000 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000-051

052-101

102-152

153-203

204-255

10 CHANNEL

MODE

FUNCTION DMX

Value

10 Ch

EFFECTS

NO Function

Eect 1

Eect 2

Eect 3

Eect4

Eect5 (Eects1- 4)

Eect 6

Eect 7

Eect 8

Eect 9 (Eects6- 8)

000-010

011-037

038-064

065-091

092-118

119-145

146-172

173-199

200-226

227-255

EFFECTS SPEED

Eects speed slow to fast 000 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode 1 (fast speed)

Dimmer speed mode 2 (middle speed)

Dimmer speed mode 3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

SOLAR27Q

17 CHANNEL

MODE

FUNCTION DMX

Value

17 Ch

DIMMER

0~100% 000 - 255

STROBE 1

No function

Strobe Slow to Fast

000 - 010

011 - 255

STROBE 2

No function

Strobe Slow to Fast

000 - 010

011 - 255

STROBE 3

No function

Strobe Slow to Fast

000 - 010

011 - 255

RED 1

0~100% 000 - 255

GREEN 1

0~100% 000 - 255

BLUE 1

0~100% 000 - 255

WHITE 1

0~100% 000 - 255

RED 2

0~100% 000 - 255

GREEN 2

0~100% 000 - 255

BLUE 2

0~100% 000 - 255

WHITE 2

0~100% 000 - 255

RED 3

0~100% 000 - 255

GREEN 3

0~100% 000 - 255

BLUE 3

0~100% 000 - 255

WHITE 3

0~100% 000 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

SOLAR27Q

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch o the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• When the lens is visibly damaged due to cracks or deep scratches, it must be replaced.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• In order to protect the device from overheating the cooling fans (if any), and ventilation openings

should be cleaned monthly.

To ensure optimal operation and performance for a long time it is essential to periodically clean the parts

subject to dust and grease deposits. The frequency with which the following operations are to be carried

out depends on various factors, such as the amount of the eects and the quality of the working environ-

ment (air humidity, presence of dust, salinity, etc.). Use a soft cloth dampened with any detergent liquid

for cleaning glass to remove the dirt from the reectors, from the lenses and lters.

It is recommended that the projector undergoes an annual service by a qualied technician for special

maintenance involving at least the following operations:

- General cleaning of internal parts..

- Restoring lubrication of all parts subject to friction, using lubricants specically.

- General visual check of the internal components, cabling, mechanical parts, etc.

- Electrical, photometric and functional checks; eventual repairs.

Warning: we strongly recommend internal cleaning to be carried out by qualied personnel!

4.2 TROUBLESHOOTING

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• All color faders set to 0

• Faulty LED

• Faulty LED board

• Check the power supply voltage

• Increase the value of the dimmer channels

• Increase the value of the color channels

• Replace the LED board

General low light intensity

• Dirty lens assembly

• Misaligned lens assembly

• Clean the xture regularly

• Install lens assembly properly

Fixture does not power up

• No power

• Loose or damaged power cord

• Faulty internal power supply

• Check for power on power outlet

• Check power cord

• Replace internal power supply

Fixture does not respond to DMX

• Wrong DMX addressing

• Damaged DMX cables

• Bouncing signals

• Check control panel and unit addressing

• Check DMX cables

• Install terminator as suggested

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

REV.002-12/18

Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.

La riproduzione - anche parziale - per propri scopi commerciali è vietata.

Al ne di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modicare, in qualun-

que momento e senza preavviso, le speciche menzionate nel presente manuale di istruzioni.

Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it

Page is loading ...

ProLights SOLAR27Q User manual

Brand: ProLights

Model: SOLAR27Q

Category: Stroboscopes & disco lights

Type: User manual

Download PDF

report

in other languages

italiano: ProLights SOLAR27Q Manuale utente

ProLights SOLAR27Q User manual

ProLights SOLAR27Q User manual

in other languages

Related papers

Other documents