*Actual product may vary slightly
Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product.
Observe all safety information to protect yourself and others. Failure to observe the instructions may result in property
damage and/or personal injury. Please keep instructions for future reference.
For warranty purchases, please keep your dated proof of purchase. File or attach to the manual for safe keeping.
For Customer Service, Call 1-800-348-5004
or e-mail [email protected]
40805 06/2017
This product contains or, when used, produces a chemical
known to the State of California to cause cancer and birth
defects or other reproductive harm.
(California Health & Safety Code § 25249.5, et seq.)
WARNING
17 PC AIR IMPACT WRENCH KIT W/SOCKET
40805
2
1-800-348-5004
• Follow all workshop safety rules, regulations, and conditions when using wrench.
• WARNING! Disconnect from air supply before changing accessories or servicing.
• Maintain the wrench in good condition and replace any damaged or worn parts.
Use genuine parts only. •Non-authorised parts may be dangerous and will invalidate
the warranty.
• WARNING! Check correct air pressure is maintained and not exceeded.
We recommend 90psi.
• Keep air hose away from heat, oil and sharp edges. Check air hose for wear before
each use and ensure that all connections are secure.
• Only use impact sockets which are specifically designed for use with an impact wrench.
• Wear approved safety eye/face shield, ear defenders, and hand protection.
• WARNING! Due to the possible presence of asbestos dust from brake linings, when
working around vehicle brake systems we recommend you wear suitable respiratory
protection.
• Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip
shoes.
• Keep children and non essential persons away from the working area.
• DO NOT use the wrench for a task it is not designed to perform.
• WARNING! DO NOT use wrench if damaged or thought to be faulty
(Contact Service Agent).
• DO NOT use wrench unless you have been instructed in its use by a qualified person.
• DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
• DO NOT operate wrench if you are tired, under the influence of alcohol, drugs or
intoxicating medication.
• DO NOT carry wrench with your hand on the power trigger in order to avoid
unintentional starting.
• DO NOT direct air from the air hose at yourself or others.
• When not in use disconnect from air supply and store in a safe, dry, childproof location.
SAFETY INSTRUCTIONS
Tough professional air impact wrench with fully polished alloy housing and rubber bumper.
Through type forward/reverse control. Four position adjustable air/torque selection. Fitted
with standard 1/2” square drive anvil. Fitted with rocking-dog type clutch and hardened
impact anvil. Suitable for general garage use.
INSTRUCTION & SPECIFICATION
Drive Size: . . . . . . . . . . . . . . . . . . . . . . . . . .1/2”
Operating Pressure: . . . . . . . . . . . . . . . . . . .6.2 Bar
Air Inlet Size: . . . . . . . . . . . . . . . . . . . . . . . . 1/4” BSP
Ultimate Torque: . . . . . . . . . . . . . . . . . . . . . 230 Ft/ Lbs
Free Speed: . . . . . . . . . . . . . . . . . . . . . . . . .7000/min
Air Consumption: . . . . . . . . . . . . . . . . . . . . .5 CFM
Overall Dimension: . . . . . . . . . . . . . . . . . . . 180mm x 195mm x 70mm
Net Weight(Without Accessories) . . . . . . . . 2.1kg
AIR SUPPLY
• Ensure wrench valve (or trigger) is in the "off" position before connecting to the air supply.
• You will require an air pressure of 90psi, and an air flow according to specification.
• WARNING! Ensure the air supply is clean and does not exceed 90psi while operating
the tool. Too high an air pressure and/or unclean air will shorten the product life due to
excessive wear, and may be dangerous causing damage and/or personal injury.
• Drain the air tank daily. Water in the air line will damage the tool.
• Clean air inlet filter weekly.
• Line pressure should be increased to compensate for unusually long air hoses
(over 8 metres). The minimum hose diameter should be 1/4” I.D. and fittings must have
the same inside dimensions.
• Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain
that all connections are secure.
COUPLINGS
• Vibration may cause failure if a quick change coupling is connected directly to the tool.
To overcome this, connect a leader hose to the tool. A quick change coupling may then
be used to connect the leader hose to the air line recoil hose. See Fig. 1 and Fig. 2.
PREPARING WRENCH FOR USE
3
1-800-348-5004
OPERATING INSTRUCTIONS
4
1-800-348-5004
WARNING! Ensure you read, understand and apply safety instructions before use.
• Only use impact sockets which are specifically designed for use with an impact wrench.
• Connect the wrench to the air hose as in section 3.
• Place the socket over the subject nut and depress the trigger to operate the wrench.
• To change direction push the button at the top of the handle. Direction of “R” for reverse
and “F” for forward
• The flow of air may be regulated by adjusting the flow valve at the base of the handle.
DO NOT use any additional force upon the wrench in order to remove a nut.
DO NOT allow wrench to free run for an extended period of time, as this will shorten its life.
MAINTENANCE
WARNING! Disconnect the wrench from the air supply before changing accessories,
servicing or performing any maintenance. Replace or repair damaged parts. Use genuine
parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
• Lubricate the air wrench daily with a few drops of air tool oil dripped into the air inlet.
• Check and top up the gearbox by removing grub screw located under the impact head.
• Clean the wrench after use.
• DO NOT use worn or damaged sockets.
• Loss of power or erratic action may be due to the following:
a) Excessive drain on the air line. Moisture or restriction in the air pipe.
Incorrect size or type of hose connectors. To remedy check the air supply and follow
instructions in chapter 3.
b) Grit or gum deposits in the wrench may also reduce performance. If your model has an
air strainer (located in the area of the air inlet), remove the strainer and clean it. Flush
the wrench out with gum solvent oil or an equal mixture of SAE No 10 oil and paraffin.
Allow to dry before use.
• When not in use, disconnect from the air supply, clean wrench and store it in a safe, dry,
childproof location.
5
1-800-348-5004
ASSEMBLY DIAGRAM AND PARTS LIST
Part No. Description Quantity Part No. Description Quantity
01 Protecting Rubber 1 23 Washer 4
02 Housing 1 24 Screw 4
03 Screw 1 25 Rubber 1
04 Anvil Bushing 1 26 Screw 2
05 Anvil Collar and Seal 1 27 Exhaust Deflector 1
06 "O"Ring 1 28 Screw 1
07 Anvil (1/2"SQ) 1 29 Spring 1
08 Hammer Pin 1 30 Pin 1
09 Hammer Dog 1 31 Trigger 1
10 Hammer Cage 1 32 Pin 1
11 Drive Cam 1 33 Screw 1
12 Ball Bearing 1 34 Spring 1
13 Front End Plate 1 35 "O" Ring 1
14 Rotor Blade 6 36 Air Regulator 1
15 Rotor 1 37 Valve Stem 1
16 Pin 1 38 Steel Ball 1
17 Cylinder 1 39 Spring 1
18 Pin Cylinder 1 40 Hose Adapter 1
19 Rear End Plate 1 41 Valve Slee
ve 1
20 Ball Bearing 1 42 Reverse Valve 1
21 Rear Gasket 1 43 Bushing 1
22 Rear Cover 1
Limited Manufacturer Warranty
FOT makes every effort to ensure that this product meets high quality and durability
standards. FOT warrants to the original retail consumer a 1-year limited warranty
from the date the product was purchased at retail and each product is free from
defects in materials. Warranty does not apply to defects due directly or indirectly
to misuse, abuse, negligence or accidents, repairs or alterations, or a lack of
maintenance. FOT shall in no event be liable for death, injuries to persons or
property, or for incidental, special or consequential damages arising from the
use of our products. To receive service under warranty, the original manufacturer
part must be returned for examination by an authorized service center. Shipping
and handling charges may apply. If a defect is found, FOT will either repair or
replace the product at its discretion.
DO NOT RETURN TO STORE
For Customer Service:
Email: [email protected] or Call 1-800-348-5004
6
1-800-348-5004
-
1
-
2
-
3
-
4
-
5
-
6
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Husky H4620 Installation guide
-
Max Load 36008 User manual
-
ATD Tools ATD-2112 User manual
-
SPEEDWAY 40807 User manual
-
Power Fist 8504052 Owner's manual
-
-
California Air Tools PRO 755 User guide
-
High Desert 10400 Operating instructions
-
-
