Max Load 35710 User manual

Brand: Max Load

Model: 35710

Type: User manual

36W

2160 LUMENS 12 CREE LED

COMBINATION LIGHT BAR

*Actual product may vary slightly

Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product.

Observe all safety information to protect yourself and others. Failure to observe the instructions may result in property

damage and/or personal injury. Please keep instructions for future reference.

For warranty purchases, please keep your dated proof of purchase. File or attach to the manual for safe keeping.

For Customer Service, Call 1-800-348-5004

or e-mail [email protected]

35710 03/2017

This product contains or, when used, produces a chemical

known to the State of California to cause cancer and birth

defects or other reproductive harm.

(California Health & Safety Code § 25249.5, et seq.)

WARNING

TECHNICAL SPECIFICATIONS

Bulb Type 3W CREE® LED

Bulb Qty. 12pc

Voltage

10-30V

Beam Type Combination (Spot/Flood)

Watts

36W

Lumen

2160 LM

Color Temperature

6500k

Operating Temperature -40°F to +145°F

10.276in.

3.740in.

4.173in.

92.0°

[email protected]

1-800-348-5004

WARNING

Please check your state and local laws before installing this LED off-road product. Every state/province

has different policies and procedures in place regarding aftermarket vehicle accessories.

The installation is recommended to be performed by a licensed professional. Please read the following

instructions thoroughly before installing this LED Light Bar.

LIGHT BAR USE AND CARE

1. Do not shine directly into your eyes.

2. Slowly tighten end cap bolts, do not over-tighten, stop when lock washers are flattened.

3. Do not turn on light during assembly; it may damage the light.

MOUNTING THE LED LIGHT BAR

1. Prior to installation, inspect and check the operation of this LED Light Bar to ensure that it is functioning

properly. Simply connect the Red power wire to the Positive (+) terminal on the battery and then connect

the Black wire to the Negative (-) terminal on the battery or to any other good unpainted ground source.

2. Using the included 5/16" x 9/16" screws, attach each mounting bracket to both ends of the LED Light Bar

and tighten with a 6mm Allen or hex key.

3. Identify the area where you would like to mount your LED light bar. Using the included 5/16" x 1-9/16"

screws, bolts and rubber washers, securely mount the light bar to your vehicle (Please measure carefully

before mounting).

POWERING THE LED LIGHT BAR

Note 1: Before installation, make sure to disconnect the battery for safety.

Note 2: If this light bar is directly connected to a battery, a toggle switch is needed to turn the light on/off,

as well as an in-line fuse within 12 inches of the power source.

Note 3: When you are extending the lead power wires to the light bar, it is highly recommended to solder

the connection and then to heat-shrink over the soldered connection (these materials are not included

– but they are available at most hardware or auto part stores.)

1. Connect the RED power wire to the positive output post of the toggle switch and run the appropriate

gauge wire (18 gauge at a minimum) from the input post of the toggle switch to positive (+) terminal

on the battery.

NOTE: Be sure to install the appropriate fuse (10A) for your light bar within 12 inches of your power source.

2. Next, connect the ground wire to the negative (-) terminal on the battery or any other good bare metal

ground source.

3. You can now flip the toggle switch to the "on" position to test your LED light bar for full functionality.

CAUTION

1. Work under the specified voltage DC10-30V.

2. The light becomes hot under continuous use. Don't remove or touch the casing for at least 30 minutes

after turning lamp off.

3. Keep heat-sink fins clean and free of debris to maintain air flow.

[email protected]

1-800-348-5004

Limited Manufacturer Warranty

FOT makes every effort to ensure that this product meets high quality and durability

standards. FOT warrants to the original retail consumer a 1-year limited warranty

from the date the product was purchased at retail and each product is free from

defects in materials. Warranty does not apply to defects due directly or indirectly

to misuse, abuse, negligence or accidents, repairs or alterations, or a lack of

maintenance. FOT shall in no event be liable for death, injuries to persons or

property, or for incidental, special or consequential damages arising from the

use of our products. To receive service under warranty, the original manufacturer

part must be returned for examination by an authorized service center. Shipping

and handling charges may apply. If a defect is found, FOT will either repair or

replace the product at its discretion.

DO NOT RETURN TO STORE

For Customer Service:

Email: [email protected] or Call 1-800-348-5004

[email protected]

1-800-348-5004

Max Load 35710 User manual

Max Load 35710 User manual

Max Load 35710 User manual

Related papers

Other documents