Cub Cadet 19A30037100 User manual

Type
User manual
Form No. 769-12361
(October 3, 2017)
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
OperatOrs Manual
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS PRODUCT.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
FastAttach™ All-Season Plow
19A30037100
To The Owner
1
2
Assembly & Set-Up .................................................. 3
Controls & Features ................................................ 11
Operation ................................................................ 12
Maintenance & Adjustment.................................13
Illustrated Parts List ...............................................14
Warranty ..................................................Back Cover
Table of Contents
Product Registration and Customer Support
Please register your product on our website, www.cubcadet.com.
If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of
this product, you can seek help from the experts. Choose from the options below:
Visit us on the web at www.cubcadet.com
Locate your nearest Cub Cadet Dealer at (877) 282-8684
Write to Cub Cadet LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019
Thank you for purchasing a Cub Cadet FastAttach™ All-
Season Plow. It was carefully engineered to provide excellent
performance when properly operated and maintained.
Please read this entire manual prior to operating the equipment.
It instructs you how to safely and easily set up, operate and
maintain your product. Please be sure that you, and any other
persons who will operate the product, carefully follow the
recommended safety practices at all times. Failure to do so could
result in personal injury or property damage.
All information in this manual is relative to the most recent
product information available at the time of printing. Review this
manual frequently to familiarize yourself with the product, its
features and operation.
Please be aware that this Operator’s Manual may cover a range
of product specifications for various models. Characteristics and
features discussed and/or illustrated in this manual may not be
applicable to all models. We reserve the right to change product
specifications, designs and equipment without notice and
without incurring obligation.
If you have any problems or questions concerning the product,
phone your local Cub Cadet dealer or contact us directly. Cub
Cadets Customer Support telephone numbers, website address
and mailing address can be found on this page. We want to
ensure your complete satisfaction at all times.
Throughout this manual, all references to right and left side of the
product are observed from the tractor operating position.
Thank You
Record Product Information
Before setting up and operating your new equipment, please
locate the model plate on the equipment and record the
information in the provided area to the right. This information
will be necessary, should you seek technical support via our web
site or with your local Cub Cadet dealer.
MOdel nuMber
serial nuMber
CALIFORNIA PROPOSITION 65
WARNING! This product contains a chemical(s) known to the State of California to cause
cancer, birth defects or other reproductive harm.
Assembly & Set-Up
2
3
Contents of Carton
6
22
2
5
11
21
21
12
14
15
13
12
19
20
18
16
17
8
9
10
7
3
4
1
Part Number Description Qty.
1 749-05858 Lower Control Tube 1
2 749-05855 Control Tube 1
3 720-0274 Grip 1
4 735-0246A End Plug 1
5 689-00656 Lift Handle Assembly 1
6 689-00661 Blade Assembly 1
7 689-00662 Trip Spring Kit 1
8 689-00632 Pivot Plate Assembly 1
9 711- 06173 Pivot Shaft 1
10 789-00471 Blade Tongue 1
11 689-00667 SHF Assembly 1
Part Number Description Qty.
12 747-06957 Tie Rod 2
13 741-0192 Flange Bearing 2
14 689-00663 Tongue Lock Pin Assembly 1
15 689-00691 Lever Lock Assembly 1
16 689-00686 Right Front Bracket Asy 1
17 689-00685 Left Front Bracket Asy 1
18 689-00682 Right Mounting Assembly 1
19 689-00681 Left Mounting Assembly 1
20 789-00463 Large Mounting Bracket 1
21 746-04794 Cable Lever 2
22 789-00471 Shave Plate 1
Section 2— ASSembly & Set-Up4
26
12
3
5
1
4
6
8
7
1
15
11
14
13
29
12
1
9
10
28
2
30
18
17
16
1
23
19
21
27
20
5
25
24
Hardware Pack 1 689-00677
Hardware Pack 3 689-00679
Hardware Pack 2 689-00678
Hardware Pack 5 689-00688
Hardware Pack 4 689-00680
Hardware Pack 6 689-00666
22
Hardware Pack
Section 2 — ASSembly & Set-Up
5
Part Number Description Qty.
- 689-00677 Hardware Pack 1 1
1 712-04065 Nut 4
2 710-3001 Screw 3/8-16 X .880 GR5 4
30 710-06012A Fixing Bolt 3/8-16 X .125 GR5 4
- 689-00678 Hardware Pack 2 1
1 712-04065 Nut 4
3 714-3020 Internal Cotter Pin 2
4 736-04183 Washer .395 X 1.0 X .62 4
5 710-0514 Screw 3/8-16 X 1 GR5 4
- 689-00679 Hardware Pack 3 1
1 712-04065 Nut 1
6 603-0297 Eye-Bolt 1
7 710-1625 Oval Head Screw #10-24 X 1.75 2
8 710-3180 Hex Head Bolt 5/16-18 X 1.75 2
11 710-3008 Screw 5/16-18 X .75 GR5 3
12 712-04063 Flange Lock Nut 5/16-18 5
13 712-3004A Hex Flange Nut 1
14 936-0414 Teon Washer .570X1.120x.062 1
15 738-0143 Shoulder Screw .498 Dia X .340 1
29 736-0451 Curved Washer 4
- 689-00680 Hardware Pack 4 1
16 703-0650 Blade Skid Shoe 2
17 912-3048 Hex Nut 2
18 712-04150 Nut 2
- 689-00688 Hardware Pack 5 1
1 712-04065 Nut 4
5 710-0514 Screw 3/8-16 X 1 GR5 2
12 712-04063 Flange Lock Nut 5/16-18 2
19 710-04683C Self-tapping Screw 3/8-16 X 1 1
20 710-3008 Screw 5/16-18 X .75 GR5 2
21 710-3181 Screw 1/2-13X1.50 GR5 1
22 710-3261 Screw 3/8-16 X 7.00 GR5 1
23 712-3022 Hex Nut Ctr Lk 1/2-13 2
24 732-04345 Extension Spring 1
25 936-0208 Washer .51 X 1.5 X .07 1
26 736-0234 Flat Washer .390 Id X 1.50 Od X .075 1
27 938-0507B Shoulder Screw 1
- 689-00666 Hardware Pack 6 1
9 710-0451 Carriage Bolt 5/16 - 18 .750 6
10 712-0429 Hex Nut 5/16 - 18 .750 6
28 714-0209 Cotter Pin 2
Section 2— ASSembly & Set-Up6
Required Tools
Phillips Head Screwdriver (1) 9/16” Socket Wrench (1) 9/16” Open/Box Wrench (1) 1/2” Socket Wrench (1)
15/16” Wrench (1) 3/4” Wrenches (2) 1/2” Open/Box Wrench (1) Adjustable Wrench (1)
WARNING! Disengage the PTO,
engage the brake lock, and stop the
tractor engine before performing
any preparation procedures. Place
the tractor on a firm and level
surface before beginning installation
procedures.
WARNING! The exhaust system
and surrounding areas are HOT. To
avoid personal injury, allow the
tractor to cool before beginning
any plow installation or removal
procedures.
NOTE: The hardware used to install some
components on the all-season plow has been
loosely installed for shipping purposes. To
assemble the plow it may be necessary to
remove this hardware to complete installation.
Attach Bracket Assemblies To Tractor
Note: If your tractor already has
FastAttach™ brackets installed, skip
to Large Mounting Bracket Assembly
instructions.
1. Attach FastAttach™ brackets (689-00685)
(689-00686) to the outside of the tractor
frame using 4 3/8 bolts (710-3001) and
4 locking nuts (712-04065) found in
hardware pack 1 (689-00677). See Figure
2-1.
Note: If single tube bumper is installed
on tractor, use the following alternate
step. Remove bumper by unbolting
4 fixing bolts. Using 4 new bolts
(710-06012A), attach left and right
FastAttach™ brackets (689-00685)
(689-00686) to the outside of the frame,
re-using the riv-nuts in the bumper in
place of nuts (712-04065) provided in
hardware pack 1. It is recommended to
hand start the bolts prior to tightening.
Once bolts are in place, tighten all 4
bolts.
Figure 2-1
Large Mounting Bracket Assembly
1. Attach RH and LH mounting assemblies
(689-00682) (689-00681) to large
mounting bracket (789-00463) with
4 screws (710-0514) 4 washers (736-
04183) and 4 nuts (712-04065) found in
hardware pack 2 (689-00678). See Figure
2-2.
Figure 2-2
Install Large Mounting Bracket To
Tractor
WARNING! The exhaust
system and surrounding
areas are HOT. To avoid
personal injury, allow the
tractor to cool before
beginning any plow
installation or removal
procedures.
1. Slide large mounting bracket into
brackets installed earlier on tractor. See
Figure 2-3.
Figure 2-3
2. Align FastAttach™ tabs and slide in to
secure.
3. Pull spring pins outward on each side
and rotate into place to lock. See Figure
2-4.
Figure 2-4
4. Install slotted end of tie rod (747-06957)
into bracket mounted on tractor frame
and then rotate and secure other end of
tie rod into hole and secure with 2 cotter
pins (714-3020) found in hardware pack 2
(689-00678). See Figure 2-5.
5. Repeat with the second tie rod (747-
06957) on the other side.
Figure 2-5
Note: Tighten all hardware that was left
loose in bracket assembly procedure.
Section 2 — ASSembly & Set-Up
7
6. Insert bearing flanges (741-0192) into
large mounting bracket. See Figure 2-6.
Figure 2-6
Blade Tongue Assembly
1. Attach lever lock assembly (689-00691)
to blade tongue (789-00471) with 2
screws (710-3008) and 2 flange lock nuts
(712-04063) found in hardware pack 5
(689-00688). See Figure 2-7.
2. Fasten extension spring (732-04345)
from hardware pack 5 (689-00688) to
arm of lever lock assembly (689-00691)
and blade tongue (789-00471). See
Figure 2-7.
Figure 2-7
Tongue Lock Assembly
1. Install pin lock assembly (689-00663) to
blade tongue (789-00471) with 2 bolts
(710-0514) and 2 nuts (712-04065) found
in hardware pack 5 (689-00688). See
Figure 2-8.
Figure 2-8
Large Mounting Bracket To Tongue
Assembly
1. Place large mounting bracket assembly
onto blade tongue assembly. Slide SHF
assembly (689-00667) into mounting
holes, and secure with self-tapping
screw (710-04683C) found in hardware
pack 5 (689-00688). See Figure 2-9.
Figure 2-9
Attach Blade Tongue To Pivot
Assembly
1. Secure pivot plate assembly (689-00632)
to blade tongue (789-00471) with 1 bolt
(710-3181) and 2 hex nuts (712-3022)
found in hardware pack 5 (689-00688).
Do not overtighten. Pivot Plate assembly
and Blade Tongue should rotate freely.
See Figure 2-10.
Note: Lubricate the pivot points
between the tongue and pivot plate
with an all-purpose automotive type
grease.
2. Secure pivot plate assembly (689-00632)
to blade tongue (789-00471) with
shoulder screw (938-0507B) and washer
(936-0208). Secure pivot plate assembly
on the bottom by using washer (736-
0234) and nut (712-04065) found in
hardware pack 5 (689-00688). See Figure
2-10.
3. Insert screw (710-3261) into pivot plate
assembly and fasten with nut (712-
04065) found in hardware pack 5 (689-
00688). See Figure 2-10.
Figure 2-10
Tongue Assembly To Blade Assembly
1. Slide pivot shaft (711-06173) into location
shown and secure with 2 cotter pins
(714-0209) found in hardware pack 6
(689-00666) to secure plow blade to
tongue assembly. Gently tap cotter pins
into place with a mallet if required. See
Figure 2-11.
Figure 2-11
Section 2— ASSembly & Set-Up8
Attach Trip Spring Kit
1. Remove 1 nut (712-04102) from the end
of the trip spring kit (689-00662) and
insert hook end around screw (710-3261)
that was installed previously. Insert
threaded end through mounting hole
in blade and fasten the nut (712-04102)
removed earlier to secure the trip spring
to the blade. See Figure 2-12.
Figure 2-12
Install Skid Shoes
1. Using the hardware found in hardware
pack 4 (689-00680) thread hex nut (912-
3048) onto skid shoe (703-0650).
2. Slide assembly through the mounting
tab located on the plow blade and use
a flangelock nut (712-04150) found in
hardware pack 4 (689-00680) to secure
the skid shoe assembly to the plow
blade. Hold the skid shoe secure at
the base while turning the top nut to
tighten. See Figure 2-13.
Figure 2-13
3. Repeat steps 1-2 to attach skid shoe
assembly on other side of plow blade.
Note: See the Maintenance &
Adjustments section regarding how to
properly adjust the trip spring and level
out the blade prior to use.
Control Handle Assembly
1. Slide grip (720-0274) onto the end of
the control tube (749-05855) (1). Slide
eye bolt (603-0297) from hardware pack
3 (689-00679) onto control tube (749-
05855)(2). See Figure 2-14.
2. Slide control tube (749-05855) into lower
control tube (749-05858) and fasten with
two bolts (710-3180), 4 curved washers
(736-0451), and 2 flange lock nuts (712-
04063) (3) found in hardware pack 3
(689-00679). See Figure 2-14.
1
2
3
Figure 2-14
3. If not pre-installed from the factory,
install end plug (735-0246A) into end of
lift handle (689-00656).
4. Connect lift handle (689-00656) to
control tube assembly and fasten the
eye bolt (603-0297) with hex flange nut
(712-3004A) found in hardware pack 3
(689-00679). See Figure 2-15.
Figure 2-15
Attach Lift Handle
1. Attach the plate end of the lift handle
(689-00656) to the SHF Assembly
(689-0667) with 3 screws (710-3008),
and 3 flange lock nuts (712-04063) from
hardware pack 3 (689-00679). See Figure
2-16.
Figure 2-16
Attach Control Handle To Pivot
Assembly
1. Attach control tube assembly to pivot
plate assembly (689-00632) with
shoulder screw (738-0143), Teflon
washer (936-0414), and nut (712-04065)
found in hardware pack 3 (689-00679).
See Figure 2-17.
Figure 2-17
Section 2 — ASSembly & Set-Up
9
2. Mount the cable levers (746-04794)
to the control tube with 2 #10 screws
(710-1625) found in hardware pack 3
(689-00679). See Figure 2-18.
Figure 2-18
Attach Cable To Tongue Lock
1. Attach the end of the blade lift cable
lever by insterting the S-end of the cable
into the hole located on the tongue
lock pin assembly (689-00663) and then
rotate the S-end pin to lock into place.
2. Slide the top nut and washer up and
then slide into mounting slot located on
the handle lift assembly bracket (689-
00656). See Figure 2-19.
Figure 2-19
3. Tighten nut to secure in place.
Tip: Lower the blade to the ground to allow
more room to tighten the nuts.
Attach Cable To Lever Lock
1. Attach the end of the pivot release cable
lever to the lever lock by inserting the
S-end of the cable into the hole located
on the lever lock assembly (689-00691)
and then rotating the cable assembly
vertically.
2. Slide the top nut and washer up and
then slide into mounting slot located
on the lever lock assembly (689-00691)
mounting bracket. See Figure 2-20.
Figure 2-20
3. Tighten nut to secure in place.
Note: Cable ties may be used to secure
the cables to handles.
Shave Plate Installation - 15” Tires
1. Check sidewall of tire to confirm tire size.
2. For tractors with 15” front tires, using
the lower set of mounting holes, install
the shave plate (789-00467) to the blade
assembly (689-00661) with six carriage
bolts (710-0451) and six flange lock nuts
(912-0429) from hardware pack 6 (689-
00666). See Figure 2-21.
Figure 2-21
Note: When the shave plate is
reinstalled, adjustment of the skid shoes
may be required.
Shave Plate Installation - 16” Tires
1. Check sidewall of tire to confirm tire size.
2. For tractors with 16” front tires, using
the top set of mounting holes, install
the shave plate (789-00467) to the blade
assembly (689-00661) with six carriage
bolts (710-0451) and six flange lock nuts
(912-0429) from hardware pack 6. See
Figure 2-22.
Figure 2-22
Note: When the shave plate is
reinstalled, adjustment of the skid shoes
may be required.
Blade Removal
WARNING! The exhaust system
and surrounding areas are HOT.
To avoid personal injury, allow
the tractor to cool before
beginning any plow installation
or removal procedures.
To remove the blade continue as follows:
1. Lock blade in the up position.
2. Pull spring pins outward on each side
and rotate into storage position. See
Figure 2-23.
Figure 2-23
Section 2— ASSembly & Set-Up10
3. Move blade to down position.
4. Remove cotter pins from tie rods (1). See
Figure 2-24.
5. Remove tie rod by pushing end of
rod through the bracket (2), and then
rotating rod to align rod tabs to slot in
bracket. Slide rod out of bracket (3). See
Figure 2-24.
1
2
3
Figure 2-24
6. Slide plow assembly out of mounting
brackets. See Figure 2-25.
Figure 2-25
Note: Pulling up slightly on the plow
assembly may make sliding the plow out
of the brackets easier.
Note: The FastAttach™ brackets
(689-00685/689-00686) may be left
in place for use with the 19A30038100
FastAttach™ Brush Guard and other
front FastAttach™ Attachments.
FastAttach™ Front Attachments
Description Part Number
All-Season Plow 19A30037100
Brush Guard 19A30038100
More coming soon. Visit your local Cub Cadet Dealer or CubCadet.com for more information.
FastAttach™ Rear Attachments
Spreader (100 lb capacity) 19A30028100
Cargo Carrier (80 lb capacity) 19A30029100
Bagger (42" and 46" Decks) 19A30030100
Sprayer / Cargo Carrier Combo 19A30035100
More coming soon. Visit your local Cub Cadet Dealer or CubCadet.com for more information.
To optimize your experience in the snow, consider these convenient attachments:
Tire Chains (for 20" rear tires) 490-241-0023
Tire Chains (for 22" rear tires) 490-241-0025
Rear Weight Kit 490-900-M060
Snow Cab 19A40022100
Controls & Features
3
11
Blade
The blade is used to push snow/dirt/gravel, etc. and can be
angled left or right and raised or lowered.
Blade Lift Cable Lever
The blade lift cable lever is used to raise and lower the blade.
Squeeze the trigger against the handle, press the handle down
and slowly release to lower the blade.
Pivot Release Cable Lever
The pivot release cable lever is used to change the angle of the
blade. Squeeze the trigger against the handle and push the
blade pivot handle forward to angle the blade to the left or pull
back on the blade pivot handle to angle the blade to the right.
Release the handle to secure into position.
Skid Shoe (Not shown)
The skid shoes are located on the bottom of the blade and can
be adjusted up or down depending on the conditions. The skid
shoes set the distance between the ground and the bottom of
the blade.
Shave Plate
The shave plate maintains contact with the surface to be plowed
as the blade is pushed forward.
Blade Lift
Cable Lever
Blade
Pivot Release
Cable Lever
Shave Plate
(Blade Cutting Edge)
Operation
4
12
Operation
WARNING! Before operating the
tractor, familiarize yourself with
the SAFE OPERATION PRACTICES
in the rider manual starting on
page 3.
To change the angle of the plow, squeeze the
plow release cable lever against the handle and
push forward on the plow adjustment handle
to angle the plow to the left or pull back on the
plow adjustment handle to angle it to the right.
The plow can be angled 30° to the right, 30° to
the left, or straight ahead. Release the handle to
secure into the desired position. See Figure 4-1.
Tip: Adjusting the angle of the blade may be
easier when the blade is in the up position.
Figure 4-1
CAUTION! It is important that
the plow is locked into position.
After releasing the lever, push or
pull the plow adjustment handle
to be certain the plow is locked
into one of the three positions.
To raise or lower the plow, use the plow lift
cable lever. See Figure 4-2.
Figure 4-2
NOTE: The plow is designed for clearing snow,
leveling soft dirt or sand and other light duty
dozer jobs. The spring trip release protects the
plow, tractor and operator from severe shock
loads when the plow comes in contact with
curbs and other obstacles. Normal use will
eventually cause the shave plate to wear. The
shave plate is reversible and replaceable.
WARNING! Operate the tractor
at a slow ground speed until
familiar with the operation of the
plow.
CAUTION! Never operate the
tractor at high speeds. A collision
with a hidden obstacle may
damage the plow cutting edge
and unseat the driver.
WARNING! Exercise caution
while operating tractor with this
attachment, especially when
traveling in reverse.
1. Pushing snow — Adjust the skid shoes
so the plow cutting edge just clears the
surface to be plowed. In large open flat
areas, the tractor can be operated at
medium speed.
NOTE: See the Maintenance &
Adjustments section for instructions for
adjusting the skid shoes.
2. Light grading — For light grading and
spreading soil, sand, gravel, etc., adjust
the shoes so they are even with the
cutting edge. Control the plow position
with the plow lift lever. Operate the
tractor at slow or medium speed.
3. Heavy grading — For heavy grading of
soil, sand, gravel, etc., adjust the shoes so
they are slightly above the cutting edge.
Control the plow position with the plow
lift lever. Operate the tractor at slow
speed.
4. Terracing — For terracing, adjust
the shoes so they are approximately
/” or more above the cutting edge,
depending on the rate of plow
penetration desired. Angle the plow
away from the trench cut by the plow.
Control the plow depth with the plow lift
lever. Operate the tractor at slow speed.
Once the desired angle of the terrace is
achieved, level the plow and continue
grading until the desired terrace depth
or width is obtained.
Maintenance & Adjustments
5
13
Maintenance
Lubrication
Periodically lubricate the pivot points between
the tongue and pivot plate with an all-purpose
automotive type grease. Periodically spray
lube the pivot latch components. See Figure
5-1.
Figure 5-1
Adjustments
Skid Shoes
NOTE: Adjust the skid shoes so the blade
cutting edge just clears the surface to be
plowed when being used for snow removal.
Adjust the skid shoes to the appropriate
position for the job being performed. See
Figure 5-2.
1. Loosen the jam nuts and lock washers on
each shoe.
2. Turn the skid shoes to the desired
position.
3. Tighten the jam nuts and lock washers.
Figure 5-2
Blade Lift Cable Tension
Adjustments
1. Using the two nuts on the ferrule adjust
tension on cable using ferrule position
so that locking pin retracts and clears the
inside of the large mounting bracket. See
Figure 5-3.
Figure 5-3
2. Test the tension by squeezing the trigger
against the handle and raising and
lowering the blade.
Pivot Release Cable Tension
Adjustments
1. Using the two nuts on the ferrule adjust
tension on cable using ferrule position
so that pivot locking lever fully clears the
pivot plate by at least 1/8”. See Figure
5-4.
Figure 5-4
2. With the blade locked in the lift position,
test by squeezing the trigger against the
handle and pushing/pulling the control
handle to pivot the blade. Blade should
pivot freely.
Shave Plate
If the shave plate becomes worn, rotate or
replace the bar as follows. See Figure 5-5.
Figure 5-5
1. Remove the six carriage bolts and flange
lock nuts fastening the shave plate to the
blade.
2. Rotate or replace the shave plate and
attach with the carriage bolts and flange
lock nuts using the alternate set of
mounting holes.
Note: When the shave plate is reinstalled,
adjustment of the skid shoes may be
required.
Trip Spring
Maintain the proper trip spring tension as
described below. See Figure 5-6.
Figure 5-6
1. There should be a 1 ⁄” - 1 ⁄” max gap
between the top of the threaded rod
and the upper lip of the blade.
2. Tighten or loosen the nuts to obtain the
proper gap.
1 ⁄” - 1 ⁄”Max Gap
15Section 7 — illuStrated PartS liSt
Ref.
Part Number Description
1 689-00632 Pivot Plate Assembly
2 941-0170 Flange Bearing
3 946-04794 Blade Release Cable
4 735-0246A End Plug
5 720-0274 Grip
6 789-00471 Blade Tongue
7 689-00656 Lift Handle
8 749-05858 Rh Lower Control Tube
9 749-05855 Rh Control Tube
10 747-06597 Support Frame Rod
11 689-00667 SHF Assembly
12 789-00466 Blade Pivot Mounting Bracket
13 789-00470 Cable Lift Link
14 789-00510 Pivot Blade Lever
15 714-0209 Cotter Pin
16 711-06173 Pivot Shaft
17 689-00686 Front Bracket Assembly RH
18 689-00685 Front Bracket Assembly LH
19 712-04063 Flange Lock Nut 5/16-18
20 710-3001 Screw 3/8-16 X .880
21 789-00463 Large Mounting Bracket
22 689-00681 LH Mounting Assembly
23 689-00682 RH Mounting Assembly
24 710-04844 Screw 10-24 X .6
25 2592 Washer
26 747-06383A Lift Lock Rod
27 712-0161 Nut Hexlock #10-24
28 789-00468 Lift Bracket
29 732-05216 Spring
30 714-3004 Cotter Pin 3/32 X 1.25
31 736-0272 Washer
32 789-00467 Shave Plate
33 689-00661 Blade Assembly 46
34 689-00662 Trip Spring Kit
35 710 -1233 Screw #10-24 X 1.375
36 603-0297 Eyebolt
37 712-3004A Hex Flange Nut
38 710-0514 Screw 3/8-16 X 1 Gr5
39 736-04183 Washer-.395 X 1.0 X .62
40 710-3261 Screw 3/8-16 X 7.00 Gr5
41 710-0451 Carriage Bolt 5/16-18 X .75
42 912-0429 Hex Nut
43 703-0650 Skid Shoe Assembly
44 712-04065 Nut
45 712-3022 Hex Nut Center Lock 1/2-13
46 738-0507B Shoulder Screw
47 710-3181 Screw 1/2-13X1.50 Gr5
48 710-04683C Screw 3/8-16 X 1
49 710-3008 Screw 5/16-18 X .75 Gr5
50 732-04345 Extension Spring
51 714-3020 Internal Cotter Pin
52 738-0143 Shoulder Screw .498 Dia X .340
53 936-0414 Teon Washer .570 X 1.120 x .062
54 712-04150 Nut
55 712-3048 Hex Nut
56 936-0208 Washer .51 X 1.5 X .07
57 736-0234 Flat Washer .390 Id X 1.50 Od X .075
58 736-3078 Flat Washer 344 X 1.00
59 712-3010 Hex Nut
60 710-1250 Carriage Bolt 5/16-18 X 1.5
61 712-04102 Hex Nut
62 738-04425 Shoulder Screw
IMPORTANT: To obtain warranty coverage owner may be required
to present an original proof of purchase and applicable maintenance
records to the servicing dealer. Please see the operator’s manual for
information on required maintenance and service intervals.
The limited warranty set forth below is given by Cub Cadet LLC with
respect to new merchandise purchased or leased and used in the
United States and/or its territories and possessions, and by MTD
Products Limited with respect to new merchandise purchased or
leased and used in Canada and/or its territories and possessions
(either entity respectively, “Cub Cadet”).
Cub Cadet warrants this product (excluding its Normal Wear Parts,
as described below) against defects in material and workmanship
for a period of one (1) year commencing on the date of original retail
purchase or lease and will, at its option, repair or replace, free of
charge, any part found to be defective in materials or workmanship.
Normal Wear Parts are warranted to be free from defects in material
and workmanship for a period of thirty (30) days from the date of
original purchase or lease. Normal wear parts include, but are not
limited to items such as: belts, blades, blade adapters, grass bags,
rider deck wheels, seats, and tires.
This limited warranty shall only apply if this product has been
operated and maintained in accordance with the Operator’s
Manual furnished with the product, and has not been subject to
misuse, abuse, neglect, accident, improper maintenance, alteration,
vandalism, theft, fire, water, or damage because of other peril or
natural disaster. Damage resulting from the installation or use of any
part, accessory or attachment not approved by Cub Cadet for use
with the product(s) covered by this manual will void your warranty as
to any resulting damage. In addition, Cub Cadet may deny warranty
coverage if the hour meter, or any part thereof, is altered, modified,
disconnected or otherwise tampered with.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE AND APPLICABLE MAINTENANCE RECORDS,
through your local authorized service dealer. To locate the dealer in
your area:
In the U.S.A.
Check your Yellow Pages, or contact Cub Cadet LLC at P.O. Box 361131,
Cleveland, Ohio 44136-0019, call 1-877-282- 8684
or log on to our website at www.cubcadet.com.
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, call 1-800-
668-1238 or log on to our website at www.mtdcanada.com.
Without limiting the foregoing, this limited warranty does not provide
coverage in the following cases:
a. Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments,
deck adjustments, and normal deterioration of the exterior
finish due to use or exposure.
b. Service completed by someone other than an authorized
service dealer.
c. Cub Cadet does not extend any warranty for products sold
or exported outside of the United States and/or Canada, and
their respective possessions and territories, except those sold
through Cub Cadet’s authorized channels of export distribution.
d. Replacement parts and\or accessories that are not genuine Cub
Cadet parts.
e. Transportation charges and service calls.
f. Commercial or Institutional Use.
There are no implied warranties, including without limitation
any implied warranty of merchantability or fitness for a
particular purpose. No warranties shall apply after the
applicable period of express written warranty above. No other
express warranties beyond those mentioned above, given by
any person or entity, including a dealer or retailer, with respect
to any product, shall bind Cub Cadet. The exclusive remedy is
repair or replacement of the product as set forth above.
The terms of this warranty provide the sole and exclusive
remedy arising from the sale and/or lease of the products
covered hereby. Cub Cadet shall not be liable for any incidental
or consequential loss or damage including, without limitation,
expenses incurred for substitute or replacement lawn care
services or for rental expenses to temporarily replace a
warranted product.
Some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, or limitations on how long an
implied warranty lasts, so the above exclusions or limitations may not
apply to you.
In no event shall recovery of any kind be greater than the amount of
the purchase price of the product sold. Alteration of safety features
of the product shall void this warranty. You assume the risk and
liability for loss, damage, or injury to you and your property and/or to
others and their property arising out of the misuse or inability to use
the product.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased as a
gift.
HOW LOCAL LAWS RELATE TO THIS WARRANTY: This limited
warranty gives you specific legal rights, and you may also have other
rights that vary in different jurisdictions.
CUB CADET LLC
MANUFACTURER’S LIMITED WARRANTY
FOR SEPARATELY SOLD ATTACHMENTS AND ACCESSORIES
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019, Phone: 1-877-282-8684
MTD Products Limited, Kitchener, ON N2G 4J1, Phone: 1-800-668-1238
GDOC-100177 REV. A
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Manual del OperadOr
ADVERTENCIA
LEA Y CUMPLA TODAS LAS REGLAS Y LAS INSTRUCCIONES DE SEGURIDAD DE ESTE MANUAL
ANTES DE INTENTAR OPERAR ESTE PRODUCTO.
SI NO SE CUMPLEN ESTAS INSTRUCCIONES, SE PUEDEN PROVOCAR LESIONES PERSONALES.
Arado FastAttach™ para aplicaciones múltiples
19A30037100
Fomulaire no 769-12361
(19 septembre 2017)
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Manuel de l'utilisateur
AVERTISSEMENT
LISEZ ET SUIVEZ TOUTES LES RÈGLES ET LES DIRECTIVES DE SÉCURITÉ OFFERTES DANS CE
MANUEL AVANT DE FAIRE FONCTIONNER CE PRODUIT.
LE NONRESPECT DE CES INSTRUCTIONS PEUT ENTRNER DES BLESSURES CORPORELLES.
Charrue quatre saisons FastAttach
MC
19A30037100
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Cub Cadet 19A30037100 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI