Symmons 6706-TRM-STN Installation guide

Identity

™

Model Numbers

Tub/Shower/Hand Shower System

Operation & Maintenance Manual

6706

Modiﬁcations

Speciﬁcation



6706

Identity Tub/Shower/Hand Shower System

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Compliance

-ASME A112.18.1/CSA B125.1

-WaterSense 1.5 gpm (5.7 L/min)

Certied by

CSA Group

Tub/shower/hand shower system powered by the

Temptrol

®

pressure-balancing valve. Features adjustable

stop screw to limit handle turn, separate three function

diverter, non-diverter tub spout, wall ell, in-line vacuum

breaker, 60" exible metal hose, hand shower cradle,

1 mode hand shower, 1 mode showerhead with easy to

clean rubber nozzles and standard 2.5 gpm (9.5 L/min) ow

restrictors. Components made from metal and nonmetallic

materials, plated in standard polished chrome nish.

Note: Append appropriate -sufx to model number.

For California Residents

WARNING: This product contains chemicals known to the

State of California to cause cancer, birth defects, or other

reproductive harm.



-1.5 1.5 gpm (5.7 L/min) ﬂow restrictor



-2.0 2.0 gpm (7.6 L/min) ﬂow restrictor



-72

6' metal hose in place of 5' standard

metal hose



-143 3 mode showerhead



-145 5 mode showerhead



-231 2 mode showerhead



-B30

30" slide bar in place of wall cradle



-B48

48" slide bar in place of wall cradle



-CHKS Integral check stops - for use in

installations where a positive shut-off

device is used downstream of mixing valve



-IPS

1/2" female IPS connections



-L/HD

Less showerhead



-L/HS

Less hand shower



-LP Loop handle



-LR Lever handle



-OP 13" oval plate



-QD

Quick disconnect on hand shower units



-R

White vinyl hose in place of metal hose



-REB-TRM

Rebuild trim kit



-REV Reverse coring, hot on right, cold on

left, for back to back installations



-SS Slip spout on any tub/shower/hand

shower unit



-STN Satin Nickel ﬁnish



-T724 24" slide / grab bar with ADA hand

shower in place of standard hand show-

er unit



-T736 36" slide / grab bar with ADA hand

shower in place of standard hand show-

er unit



-TRM Trim only, valve not included



-X Integral service stops - allows water

shutoff at valve for service

2

Dimensions

Notes:

1) All dimensions measured from nominal rough-in (see I as reference).

2) Dimensions subject to change without notice.

FLOORFLOOR

MM

CC

OOGG

KK

HH

FF

AA PP

QQ

SS

LL

NN

II

BB

EE

DD

JJ

RR

TT

UU

VV

Measurements

A 5-7/8", 149 mm

B 4-5/8", 117 mm

C

Male 1/2" NPT tting must

be recessed 1/4" (6 mm)

from nished wall

D

Diverter Valve Hole Size

Min. Ø 3", 76 mm

Max. Ø 3-1/4", 83 mm

E 3-5/8", 92 mm

F 2-7/8", 73 mm

G Ref. 10", 254 mm

H

Shower Valve Hole Size

Min. Ø 3", 76 mm

Max. Ø 4", 102 mm

I

Rough-in

2-3/8" ± 1/2", 60 mm ± 13 mm

J 3-1/2", 89 mm

K 12", 305 mm

L

Male 1/2" NPT tting must

protrude 4" (102 mm)

from nished wall

M Ref. 32", 813 mm

N 5-1/2", 140 mm

O Ref. 77", 1956 mm

P Ø 2-1/2", 64 mm

Q Ø 3-1/8", 79 mm

R 6", 152 mm

S 2-1/8", 54 mm

T Ø 5", 127 mm

U Ø 6-3/8", 162 mm

V Ø 2-1/2", 64 mm

3

Parts Breakdown

HOT

Water Supply

COLD

Water Supply

I

J

K

Q

R

S

L

N

O

P

M

K

J

I

A

B

C

E

F

G

H

D

T

*Note: Append -STN to part number for

Satin Nickel nish.

Replacement Parts

Item Description Part Number

A Hand Shower EF-100*

B

D

Wall Ell

Set Screw

EF-105*

C

E

F

Mounting Plate

Wall Cradle

Screws

EF-106*

G

H

Vacuum Breaker

60" Hose

EF-104*

I Showerhead 672SH*

J

K

Shower Arm

Flange

300S*

L

M

Handle

Set Screw

RTS-281*

N Dome Cover T-19*

O

P

Diverter

Escutcheon Kit

67-DIV*

Q

R

S

Shower

Escutcheon Kit

6700-ESC*

T Tub Spout 060*

Tools Required for Installation

Adjustable

Wrench

Allen Wrench

3/32"

Phillips Head

Screwdriver

Plumber Tape

Silicone

Notes:

1) Apply a bead of silicone around the perimeter of all shower trim in-

stalled ush to the nished wall (less mounting plates and brackets).

Leave opening on bottom of escutcheons for weep hole.

2) Apply plumber tape to all threaded connections.

4

Note:

For valve body installation, please

see valve body manual.

1

R

S

R

2

1) Install shower mounting plate (S)

to shower valve. Secure with two

screws (R).

2) Attach shower escutcheon (Q) to

shower mounting plate (S).

Q S

Note: Tabs should snap into place.

N

1

2

4) Install dome covers (N) to valves.

Turn clockwise to secure.

Installation

1

2

3

K

J

6) Attach shower arm (J) and ange

(K) to vertical shower pipe. Turn

clockwise to tighten.

5) Install handles (L) to valves.Secure

handles with set screws (M).

L

1

2

M

7) Install showerhead (I) to shower

arm (J). Turn clockwise to tighten.

1

J

1

I

2

3) Install diverter escutcheon (P) to

diverter valve. Secure with two

screws (O).

1

P

O

2

8) Install wall ell

(B)

to pipe tting.

Secure wall ell with set screw (D).

B

1

D

2

5

Installation

Operation (Temperature Control)

1) Turn shower handle counter-

clockwise approximately 1/4 turn

to put valve in cold position.

2) Turn shower handle counter-

clockwise approximately 1/2 turn

to put valve in warm position.

3) Turn shower handle counter-

clockwise approximately 3/4 turn

to put valve in hot position.

1

3

C

4

U2

U3

U1

U2

2

Note: For dry wall 1/2" thick or less,

insert anchor tool (U3) into drywall

anchor (U2) to secure behind wall

prior to installing wall cradle.

9) Place mounting plate

(C)

in po-

sition, mark and drill 3/16" holes

for tile anchors (U1), 5/16" holes

for drywall anchors (U2). Install

anchors.

10) Remove cover of hand show-

er cradle

(E)

. Install cradle and

mounting plate

(C)

. Secure with

three screws

(F)

. Replace cover

on hand shower cradle.

1

2

4

E

F

C

3

11) Attach vacuum breaker (G) to wall

ell (B). Attach hose (H) to vacuum

breaker. Attach hand shower (A)

to hose (H). Turn clockwise to

tighten.

5

3

1

2

4

A

H

G

B

T

1

2

12) Install tub spout (T) to pipe tting

Turn clockwise to tighten.

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621

Problem Cause Solution

Finish is spotting.

Elements in water supply may cause

water staining on nish.

Clean nished trim area with a soft

cloth using mild soap and water or a

non-abrasive cleaner and then quickly

rinse with water.

Troubleshooting Chart

Operation (Diverter Control)

POSITION 1

POSITION 2

POSITION 3

1) Cartridge is factory set to divert to

function 1.

2) Turn handle to position 2 to divert

to function 2.

3) Turn handle to position 3 to divert

to function 3.

POSITION 4

POSITION 5

POSITION 6

4) Turn handle to position 4 to share

functions 2 and 3.

5) Turn handle to position 5 to share

functions 1 and 3.

6) Turn handle to position 6 to share

functions 1 and 2.

Page is loading ...

Symmons 6706-TRM-STN Installation guide

This manual is also suitable for

Symmons 6706-TRM-STN Installation guide

in other languages

Related papers

Other documents