Identity
™
Model Numbers
Tub/Shower/Hand Shower System
Operation & Maintenance Manual
6706
Modifications
Specification
6706
Identity Tub/Shower/Hand Shower System
Warranty
Limited Lifetime - to the original end purchaser in
consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
Compliance
-ASME A112.18.1/CSA B125.1
-WaterSense 1.5 gpm (5.7 L/min)
Certied by
CSA Group
Tub/shower/hand shower system powered by the
Temptrol
®
pressure-balancing valve. Features adjustable
stop screw to limit handle turn, separate three function
diverter, non-diverter tub spout, wall ell, in-line vacuum
breaker, 60" exible metal hose, hand shower cradle,
1 mode hand shower, 1 mode showerhead with easy to
clean rubber nozzles and standard 2.5 gpm (9.5 L/min) ow
restrictors. Components made from metal and nonmetallic
materials, plated in standard polished chrome nish.
Note: Append appropriate -sufx to model number.
For California Residents
WARNING: This product contains chemicals known to the
State of California to cause cancer, birth defects, or other
reproductive harm.
-1.5 1.5 gpm (5.7 L/min) flow restrictor
-2.0 2.0 gpm (7.6 L/min) flow restrictor
-72
6' metal hose in place of 5' standard
metal hose
-143 3 mode showerhead
-145 5 mode showerhead
-231 2 mode showerhead
-B30
30" slide bar in place of wall cradle
-B48
48" slide bar in place of wall cradle
-CHKS Integral check stops - for use in
installations where a positive shut-off
device is used downstream of mixing valve
-IPS
1/2" female IPS connections
-L/HD
Less showerhead
-L/HS
Less hand shower
-LP Loop handle
-LR Lever handle
-OP 13" oval plate
-QD
Quick disconnect on hand shower units
-R
White vinyl hose in place of metal hose
-REB-TRM
Rebuild trim kit
-REV Reverse coring, hot on right, cold on
left, for back to back installations
-SS Slip spout on any tub/shower/hand
shower unit
-STN Satin Nickel finish
-T724 24" slide / grab bar with ADA hand
shower in place of standard hand show-
er unit
-T736 36" slide / grab bar with ADA hand
shower in place of standard hand show-
er unit
-TRM Trim only, valve not included
-X Integral service stops - allows water
shutoff at valve for service
2
Dimensions
Notes:
1) All dimensions measured from nominal rough-in (see I as reference).
2) Dimensions subject to change without notice.
FLOORFLOOR
MM
CC
OOGG
KK
HH
FF
AA PP
QQ
SS
LL
NN
II
BB
EE
DD
JJ
RR
TT
UU
VV
Measurements
A 5-7/8", 149 mm
B 4-5/8", 117 mm
C
Male 1/2" NPT tting must
be recessed 1/4" (6 mm)
from nished wall
D
Diverter Valve Hole Size
Min. Ø 3", 76 mm
Max. Ø 3-1/4", 83 mm
E 3-5/8", 92 mm
F 2-7/8", 73 mm
G Ref. 10", 254 mm
H
Shower Valve Hole Size
Min. Ø 3", 76 mm
Max. Ø 4", 102 mm
I
Rough-in
2-3/8" ± 1/2", 60 mm ± 13 mm
J 3-1/2", 89 mm
K 12", 305 mm
L
Male 1/2" NPT tting must
protrude 4" (102 mm)
from nished wall
M Ref. 32", 813 mm
N 5-1/2", 140 mm
O Ref. 77", 1956 mm
P Ø 2-1/2", 64 mm
Q Ø 3-1/8", 79 mm
R 6", 152 mm
S 2-1/8", 54 mm
T Ø 5", 127 mm
U Ø 6-3/8", 162 mm
V Ø 2-1/2", 64 mm
3
Parts Breakdown
HOT
Water Supply
COLD
Water Supply
I
J
K
Q
R
R
S
L
N
O
O
P
M
K
J
I
A
B
C
E
F
G
H
D
T
*Note: Append -STN to part number for
Satin Nickel nish.
Replacement Parts
Item Description Part Number
A Hand Shower EF-100*
B
D
Wall Ell
Set Screw
EF-105*
C
E
F
Mounting Plate
Wall Cradle
Screws
EF-106*
G
H
Vacuum Breaker
60" Hose
EF-104*
I Showerhead 672SH*
J
K
Shower Arm
Flange
300S*
L
M
Handle
Set Screw
RTS-281*
N Dome Cover T-19*
O
P
Diverter
Escutcheon Kit
67-DIV*
Q
R
S
Shower
Escutcheon Kit
6700-ESC*
T Tub Spout 060*
Tools Required for Installation
Adjustable
Wrench
Allen Wrench
3/32"
Phillips Head
Screwdriver
Plumber Tape
Silicone
Notes:
1) Apply a bead of silicone around the perimeter of all shower trim in-
stalled ush to the nished wall (less mounting plates and brackets).
Leave opening on bottom of escutcheons for weep hole.
2) Apply plumber tape to all threaded connections.
4
Note:
For valve body installation, please
see valve body manual.
1
R
S
R
2
1) Install shower mounting plate (S)
to shower valve. Secure with two
screws (R).
2) Attach shower escutcheon (Q) to
shower mounting plate (S).
Q S
Note: Tabs should snap into place.
N
1
1
2
4) Install dome covers (N) to valves.
Turn clockwise to secure.
Installation
1
1
2
3
K
J
6) Attach shower arm (J) and ange
(K) to vertical shower pipe. Turn
clockwise to tighten.
5) Install handles (L) to valves.Secure
handles with set screws (M).
L
1
1
2
M
7) Install showerhead (I) to shower
arm (J). Turn clockwise to tighten.
1
J
1
I
2
3) Install diverter escutcheon (P) to
diverter valve. Secure with two
screws (O).
1
P
O
2
8) Install wall ell
(B)
to pipe tting.
Secure wall ell with set screw (D).
B
1
1
D
2
5
Installation
Operation (Temperature Control)
1) Turn shower handle counter-
clockwise approximately 1/4 turn
to put valve in cold position.
2) Turn shower handle counter-
clockwise approximately 1/2 turn
to put valve in warm position.
3) Turn shower handle counter-
clockwise approximately 3/4 turn
to put valve in hot position.
1
3
C
4
U2
U3
U1
U2
2
Note: For dry wall 1/2" thick or less,
insert anchor tool (U3) into drywall
anchor (U2) to secure behind wall
prior to installing wall cradle.
9) Place mounting plate
(C)
in po-
sition, mark and drill 3/16" holes
for tile anchors (U1), 5/16" holes
for drywall anchors (U2). Install
anchors.
10) Remove cover of hand show-
er cradle
(E)
. Install cradle and
mounting plate
(C)
. Secure with
three screws
(F)
. Replace cover
on hand shower cradle.
1
2
4
E
F
C
3
11) Attach vacuum breaker (G) to wall
ell (B). Attach hose (H) to vacuum
breaker. Attach hand shower (A)
to hose (H). Turn clockwise to
tighten.
5
3
1
2
4
A
H
H
G
B
T
1
2
12) Install tub spout (T) to pipe tting
Turn clockwise to tighten.
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621
Copyright © 2016 Symmons Industries, Inc. ■ symmons.com ■ [email protected] ■ ZV-3199 REV 0 ■ 052416
Problem Cause Solution
Finish is spotting.
Elements in water supply may cause
water staining on nish.
Clean nished trim area with a soft
cloth using mild soap and water or a
non-abrasive cleaner and then quickly
rinse with water.
Troubleshooting Chart
Operation (Diverter Control)
POSITION 1
POSITION 2
POSITION 3
1) Cartridge is factory set to divert to
function 1.
2) Turn handle to position 2 to divert
to function 2.
3) Turn handle to position 3 to divert
to function 3.
POSITION 4
POSITION 5
POSITION 6
4) Turn handle to position 4 to share
functions 2 and 3.
5) Turn handle to position 5 to share
functions 1 and 3.
6) Turn handle to position 6 to share
functions 1 and 2.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
