2. Clinton Electronics
  3. CE-CM-SX-3

Clinton Electronics CE-CM-SX-3, CE-CM-LX-12, CE-CM-LX-17, CE-CM-S-2, CE-CM-SX-6 User manual

  • Hello! I am an AI chatbot trained to assist you with the Clinton Electronics CE-CM-SX-3 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
CLINTON Electronics
6701 Clinton Road
Loves Park, IL 61111
1.800.447.3306 Sales
1.800.549.6393 Support
1.800.633.8712 Fax
www.clintonelectronics.com
Telescopic Pole Mount
CE-CM-S-2
CE-CM-SX-6
CE-CM-SX-8
CE-CM-LX-12
CE-CM-LX-17
User Manual
7
/
16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mm
VESA screw
(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer
1/4” Washer
M4 Washer
Pole will move in
the direction of the
tightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”
Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
WARNING
Prior to installation and use of this product, please observe the following warnings:
1. Installation and servicing should be done by qualied personnel, and all work done should conform to local codes.
2. Using replacement parts or accessories other than from the manufacturer may void the warranty.
CAUTION
CHANGES OR MODIFICATIONS NOT EXPRESSLY
APPROVED BY THE PARTY RESPONSIBLE FOR
COMPLIANCE COULD VOID THE USERS AUTHORITY
TO OPERATE THE EQUIPMENT.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&F
AC24V
AUX1
AUX2
COM
ALM1
ALM2
ALM3
ALM4
ALM5
ALM6
ALM7
485A
485B
485A
485B
AC24V
AC220V
AC220V
COM
JP2
JP2_2
AC24V FUSE
J1
FUSE
5X20
Outdoor Box
Model CE-PTZ-WP24
0204201792
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
Outdoor Box
Model CE-PTZ-WP24
0204201792
LM1
LM2
LM3
LM4
LM5
LM6
LM7
85A
85B
85A
85B
AC24V
OM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&F
AC24V
AUX1
AUX2
COM
ALM1
ALM2
ALM3
ALM4
ALM5
ALM6
ALM7
485A
485B
485A
485B
AC24V
AC220V
AC220V
COM
JP2
JP2_2
AC24V FUSE
J1
FUSE
5X20
Outdoor Box
Model CE-PTZ-WP24
0204201792
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&F
AUX1
AUX2
COM
ALM1
ALM2
ALM3
ALM4
ALM5
ALM6
ALM7
485A
485B
485A
485B
AC24V
AC220V
AC220V
COM
JP2_2
AC24V FUSE
J1
FUSE
5X20
Outdoor Box
Model CE-PTZ-WP24
0204201792
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&F
AC24V
AUX1
AUX2
COM
ALM1
ALM2
ALM3
ALM4
ALM5
ALM6
ALM7
485A
485B
485A
485B
AC24V
AC220V
AC220V
COM
JP2
JP2_2
AC24V FUSE
J1
FUSE
5X20
Outdoor Box
Model CE-PTZ-WP24
0204201792
This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this unit.
Telescopic LCD ceiling mount Info:
This bracket is designed to mount to mount an LCD from the ceiling structure. It can be
used with the existing truss structure of the building or in conjunction with channel strut.
There are four lengths of brackets available:
• Part # CM-S-2 Length of 22” to 35”
• Part # CM-SX-6 Length of 36” to 67”
• Part # CM-SX-8 Length of 54” to 96”
• Part # CM-LX-12 Length of 71” to 139”
• Part # CM-LX-17 Length of 75” to 200”
(Brackets are identical except for length)
Included Hardware:
Tools Required:
7/16” wrench
7mm wrench
10mm wrench
3/4” wrench
5/16” wrench
#2 Phillips head screwdriver
level
1/4”-20 x 2” hex head bolt (1 pc.),
lock washer (1 pc.), washers (2 pcs.),
and locknut (1 pc.)
Please check to ensure all hardware is included prior to installation. If parts are missing, please contact Clinton Electronics for replacement parts.
1/2”-13 lock nut (1 pc.),
and fender washer (1 pc.)
M4 x 45 screw (1 pc.),
washers (2 pcs.), and locknut (1 pc.)
M4 x 10mm screw
to attach safety cable
to rear of display. (1 pc.)
Safety cable with crimped
eyelet. (1 pc.)
U-bolt cable
clamp. (1 pc.)
7
/
16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mm
VESA screw
(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer
1/4” Washer
M4 Washer
Pole will move in
the direction of the
tightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”
Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
7
/
16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mm
VESA screw
(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer
1/4” Washer
M4 Washer
Pole will move in
the direction of the
tightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”
Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
7
/
16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mm
VESA screw
(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer
1/4” Washer
M4 Washer
Pole will move in
the direction of the
tightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”
Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
7
/
16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mm
VESA screw
(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer
1/4” Washer
M4 Washer
Pole will move in
the direction of the
tightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”
Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
7
/
16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mm
VESA screw
(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer
1/4” Washer
M4 Washer
Pole will move in
the direction of the
tightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”
Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
7
/
16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mm
VESA screw
(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer
1/4” Washer
M4 Washer
Pole will move in
the direction of the
tightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”
Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
User Manual
(1 pc.)
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mm
VESA screw
(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer
1/4” Washer
M4 Washer
Pole will move in
the direction of the
tightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”
Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
Bracket (1 pc.)
Pole Mount
Assembly (1 pc.)
7
/
16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mm
VESA screw
(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer
1/4” Washer
M4 Washer
Pole will move in
the direction of the
tightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”
Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
AC24VIN
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&F
AC24V
AUX1
AUX2
COM
ALM1
ALM2
ALM3
ALM4
ALM5
ALM6
ALM7
485A +
485B -
485A +
485B -
AC24V
AC220V
AC220V
COM
JP2
JP2_2
AC24V FUSE
J1
FUSE
5X20
Alarm Inputs
485 Inputs
Ground
24V Input
Auxilary Inputs
Common
Common
220V Aux. Input
Alarm/Aux/Com
Output 1 to Camera
AC24V Output
to Camera
AC24V Aux. Input
5 x 20mm fuse
3A 250V
RS485 Communication
Output to Camera
Heater &
Fan Output
JP9
NOT USED WITH STANDARD SETUP
220V Aux. Input
Alarm/Aux/Com
Output 2 to Camera
IN
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&F
AC24V
AUX1
AUX2
COM
ALM1
ALM2
ALM3
ALM4
ALM5
ALM6
ALM7
485A
485B
485A
485B
AC24V
AC220V
AC220V
COM
JP2
JP2_2
AC24V FUSE
J1
FUSE
5X20
Outdoor Box
Model CE-PTZ-WP24
0204201792
2.12 in (54mm)
9.41 in (239mm)
.39 in (9.9mm)
7.94 in (202mm)
4.48 in (114mm)
6.10 in (155mm)
8.46 in (215mm)
6.69 in (170mm)
JP9
5.55 in (141mm)
M4 x 8 VESA screws
(4 pcs.)
Assembly Instructions
Truss mount or channel strut mount
Securing Mount to Building:
1. Insert threaded rod between truss gap or into hole in channel strut.
2. Place 1/2” fender washer over the threaded rod and then 1/2” lock nut.
3. Tighten the 1/2”-13 lock nut using a 3/4” wrench.
7
/
16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mm
VESA screw
(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer
1/4” Washer
M4 Washer
Pole will move in
the direction of the
tightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”
Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
Mounting LCD to Pole:
1. If your LCD is supplied with a VESA plate already mounted on the back, simply
ensure the four M4 screws are in place and tightened. If the mount is not already
attached, connect it using the supplied M4 x 8mm VESA screws (4-places).
*NOTE: Some installations may require running power and video cables
prior to attaching the LCD bracket to the pole. If this is the case, do so
before continuing to step 2.
2. Hold the LCD with attached bracket up to the end of the pole mount, and
line up the wings of the bracket to the holes in the end of the pole. Insert the
1/4”-20 x 2” bolt, lock washer, washers, and lock nut in place according to the
illustration on the right. You will use 7/16” and 10mm wrenches to fully tighten
in step 4.
3. Install the M4 x 45mm screw, washers, and lock nut into the upper slotted hole
according to the illustration on the right. You will use a #2 Phillips screwdriver
and a 7mm wrench to fully tighten in the next step.
4. Tighten the fasteners to secure the monitor at the desired angle.
*NOTE: Avoid overtightening which can cause the pole to indent.
7
/
16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mm
VESA screw
(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer
1/4” Washer
M4 Washer
Pole will move in
the direction of the
tightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”
Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
Leveling the Pole
1. You can ensure the pole is plumb by tightening the 1/4”-20 lock nuts on the top
of the pole where it attaches to the structure using a 7/16” wrench.
2. Place a level on the pole and tighten the nuts that correspond to the direction
that the pole needs to move (see illustration on the right).
3. Check and adjust 2 adjacent sides of the pole until it is plumb in each direction.
7
/
16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mm
VESA screw
(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer
1/4” Washer
M4 Washer
Pole will move in
the direction of the
tightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”
Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
Remove original
M4 x 8mm VESA
screw & replace with
M4 x 10mm screw
U-Bolt Cable Clamp
Cord Management Hole
Hold lower pole section and
turn counter-clockwise to loosen
Prevent display from falling by
holding lower pole section here
Secure assembly by turning collar clockwise:
hand tighten as snug as possible
CAUTION: This stand is intended for use only with the maximum weights indicated.
Use with products heavier than the maximum weights indicated may result in
instability causing possible injury. This product is intended to mount to a steel
support truss, or channel strut.
9/16”
If drilling is necessary,
Use 9/16” metal drill
bit to drill through steel
mounting surface.
Max Load:
15kgs / 35lbs.
Remove original
M4 x 8mm VESA
screw & replace with
M4 x 10mm screw
U-Bolt Cable Clamp
Cord Management Hole
Hold lower pole section and
turn counter-clockwise to loosen
Prevent display from falling by
holding lower pole section here
Secure assembly by turning collar clockwise:
hand tighten as snug as possible
CAUTION: This stand is intended for use only with the maximum weights indicated.
Use with products heavier than the maximum weights indicated may result in
instability causing possible injury. This product is intended to mount to a steel
support truss, or channel strut.
9/16”
If drilling is necessary,
Use 9/16” metal drill
bit to drill through steel
mounting surface.
CLINTON Electronics
6701 Clinton Road
Loves Park, IL 61111
1.800.447.3306 Sales
1.800.549.6393 Support
1.800.633.8712 Fax
www.clintonelectronics.com
Remove original
M4 x 8mm VESA
screw & replace with
M4 x 10mm screw
U-Bolt Cable Clamp
Cord Management Hole
Hold lower pole section and
turn counter-clockwise to loosen
Prevent display from falling by
holding lower pole section here
Secure assembly by turning collar clockwise:
hand tighten as snug as possible
CAUTION: This stand is intended for use only with the maximum weights indicated.
Use with products heavier than the maximum weights indicated may result in
instability causing possible injury. This product is intended to mount to a steel
support truss, or channel strut.
9/16”
If drilling is necessary,
Use 9/16” metal drill
bit to drill through steel
mounting surface.
Installing the Safety Cable:
1. Run the safety cable into the cable management hole in the top of the pole, and out through the bottom of the pole. The crimped eyelet end
will connect to the LCD.
2. Remove one of the M4 x 8mm VESA mount screws from the LCD-bracket assembly, then connect the crimped eyelet end of the safety cable
to the mount using the supplied M4 x 10mm screw. You can discard the unused M4 x 8mm VESA mount screw that has been removed as it is no
longer needed.
3. Connect the top end of the safety cable by inserting it through a hole in the truss or channel strut, and fasten using the U-Bolt cable clamp. Pull
any remaining slack from the safety cable, and fully tighten the U-Bolt using a 5/16” wrench. Cut or loop any excess cable.
Adjusting Height:
1. Hold the lower pole (where it connects to the LCD) while loosening the center collar by turning it counter-clockwise (see illustration on
left below). Extend the pole by gently lowering it to the desired length.
2. Once the proper length has been maintained, lock the pole in position by rotating the center collar clockwise. The collar should be hand
tightened as snug as possible to prevent the pole from expanding. (see illustration on right below)
Remove original
M4 x 8mm VESA
screw & replace with
M4 x 10mm screw
U-Bolt Cable Clamp
Cord Management Hole
Hold lower pole section and
turn counter-clockwise to loosen
Prevent display from falling by
holding lower pole section here
Secure assembly by turning collar clockwise:
hand tighten as snug as possible
CAUTION: This stand is intended for use only with the maximum weights indicated.
Use with products heavier than the maximum weights indicated may result in
instability causing possible injury. This product is intended to mount to a steel
support truss, or channel strut.
9/16”
If drilling is necessary,
Use 9/16” metal drill
bit to drill through steel
mounting surface.
Remove original
M4 x 8mm VESA
screw & replace with
M4 x 10mm screw
U-Bolt Cable Clamp
Cord Management Hole
Hold lower pole section and
turn counter-clockwise to loosen
Prevent display from falling by
holding lower pole section here
Secure assembly by turning collar clockwise:
hand tighten as snug as possible
CAUTION: This stand is intended for use only with the maximum weights indicated.
Use with products heavier than the maximum weights indicated may result in
instability causing possible injury. This product is intended to mount to a steel
support truss, or channel strut.
9/16”
If drilling is necessary,
Use 9/16” metal drill
bit to drill through steel
mounting surface.
Remove original
M4 x 8mm VESA
screw & replace with
M4 x 10mm screw
U-Bolt Cable Clamp
Cord Management Hole
Hold lower pole section and
turn counter-clockwise to loosen
Prevent display from falling by
holding lower pole section here
Secure assembly by turning collar clockwise:
hand tighten as snug as possible
CAUTION: This stand is intended for use only with the maximum weights indicated.
Use with products heavier than the maximum weights indicated may result in
instability causing possible injury. This product is intended to mount to a steel
support truss, or channel strut.
9/16”
If drilling is necessary,
Use 9/16” metal drill
bit to drill through steel
mounting surface.
Loosen
Tighten
v.04.06.11
/