Ronda mastertech Technical Instructions

Ronda
Brand
Ronda
Model
mastertech
Type
Technical Instructions

This manual is also suitable for

Technical Instructions 7004.P
10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 1
2000.669.G Main plate
1.
3305.363.CO Cannon pinion with driver B (Aig.1)
2.
A
2030.028.CO Centre bridge
3.
Centre bridge held by 4 screws 4000.250.
4000.250 Screw
4.
B
3406.039 Sliding attachement
5.
Sliding attachement held by 1 screw 4000.250.
2130.181.CO Combined maintaining plate
6.
Combined maintaining plate held by 1 screw 4000.250.
4000.250 Screw
7.
3016.028 Lever for setting lever
8.
Lever for setting lever held by 1 screw 4000.249.
4000.249 Screw
9.
3016.027 Stop lever
10.
Stop lever held by 1 screw 4000.249.
4000.249 Screw
11.
3622.044 Stator
12.
3715.105.RK Rotor
13.
3147.060.CO Intermediate wheel
14.
3122.070.CO Third wheel
15.
3136.174.CO Centre second wheel (Aig.1)
16.
3004.203.CO Seconde intermediate wheel
17.
3136.182.CO Small second wheel axle
18.
3136.173.CO Centre second wheel (Aig.1)
19.
C
Technical Instructions 7004.P
10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 2
2020.170.G Train wheel bridge
20.
Train wheel bridge held by 3 screws 4000.250.
4000.244 Screws
21.
3603.080 Battery insulator
22.
3601.120.G Battery clamp +
23.
Battery clamp held by 1 screw 4000.248.
4000.248 Screw
24.
3503.071 Tube
25.
D
3612.196 Electronic module
26.
Electronic module held by 5 screws 4000.250.
4000.250 Screw
27.
3603.081 Spacer
28.
2130.183.G.7004P Electronic module cover
29.
Electronic module cover held by 4 screws 4000.244.
4000.244 Screws
30.
3600.032.HGF Battery 381
31.
E
Technical Instructions 7004.P
10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 3
2000.669.G Main plate
32.
3017.054.CO Setting lever
33.
3905.063 Setting lever jumper (3 positions)
34.
Setting lever jumper held by 1 screw 4000.250. Tensioning the spring
arm.
4000.282 Screw
35.
3001.061.FI Sliding pinion
36.
F
3015.077 Yoke (3 positions)
37.
Tensioning the spring arm.
3004.200 Corrector setting wheel
38.
3004.200 Corrector setting wheel
39.
3015.078.CO Rocking bar (3 positions)
40.
Tensioning the spring arm.
G
2130.194 Setting mechanism cover
41.
Setting mechanism cover held by 4 screws 4000.305.
4000.305 Screw
42.
3000.194.CO Setting stem
43.
3004.204 Intermediate setting wheel
44.
3007.079.CO Minute wheel
45.
2130.185 Minute train bridge
46.
Minute train bridge held by 1 screw 4000.278.
4000.278 Screw
47.
3301.296.CO Hour wheel (Aig.1)
48.
3147.066.CO Date corrector setting wheel
49.
H
Technical Instructions 7004.P
10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 4
2000.672.G Main plate retro
50.
Main plate retro held by 4 screws 4000.248.
4000.248 Screw
51.
3004.209 Tens indicator driving wheel
52.
The short tooth of the tens indicator driving wheel must point to the
center of the movement. Parts 3004.209 and 3500.073 must be
exchanged together.
3500.073 Tens jumper
53.
Parts 3004.209 and 3500.073 must be exchanged together.
2130.187 Tens jumper maintaining plate
54.
Tens jumper maintaining plate held by 2 screws 4000.279. Tensioning
the spring arm.
4000.279 Screw
55.
3004.208.CO Date indicator driving wheel
56.
3147.061 Intermediate date wheel
57.
3404.006.CO Day cam (12h)
58.
Place parts as shown on graphics.
3406.032 Day rack
59.
3406.031 Day rack lever
60.
3507.059.CO Date corrector wheel
61.
2130.191 Date indicator plate
62.
3905.068 Date corrector spring
63.
Date corrector spring held by 1 screw 4000.244.
3905.066 Day rack lever spring
64.
Tensioning the spring arm.
3500.069 Day jumper
65.
Tensioning the spring arm.
3500.068 Date jumper
66.
3504.234.A6.1.A Units indicator (standard)
67.
Nick of the indicator at 3 o`clock.
I
J
K
Technical Instructions 7004.P
10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 5
2130.192 Date indicator maintaining plate
68.
Date indicator maintaining plate held by 1 screw 4000.250.
4000.250 Screw
69.
3905.064 Date jumper spring
70.
Insert the date jumper spring in the provided opening.
3907.047 Day finger flange
71.
Stem pos III: Turn crown forwards until the date jumps. Stem pos II:
Move the date until the nick is at 3 o`clock.
3004.211 Day finger
72.
Position the end of the teeth against the day came pinion while turning
softly in counterclockwise direction.
L
3004.212 Days driving wheel
73.
Insert the tooth of the wheel in the flange gap, while turning softly in
counterclockwise direction to ensure correct position of the day finger.
3401.082.FI Day indicator pinion
74.
3147.062 Tens intermediate wheel
75.
Arrow positioning radially outwards.
3315.003 Friction spring
76.
M
3504.236.A6.1.A Tens indicator (standard)
77.
Nick of the indicator at 3 o`clock.
2130.193.G Date mecanism maintaining plate
78.
Date mecanism maintaining plate held by 3 screws 4000.320.
4000.320 Screw
79.
3506.077.G Intermediate dial support
80.
Polished version first.
3506.076.G Dial support
81.
N
8200 Moebius 8200
82.
9014 Moebius 9014
83.
124 Jismaa 124
84.
9020 Moebius 9020
85.
10/2013 RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] EM 1
Electronic measurements
7004.P
Battery
381
Voltage
1.55 V
Setting stem in p
osition I, calendar not in gear,
60 s measur
ing interval for rate and consumption:
Typ
ical consumption
Maximal
consumption
1.43 µA
3.10 µA
R
ate
-10s/M. .. +20s/M.
Lower working voltage limit
1.20 V
Setting stem in position
III, 60 s measuring interval:
Typical consumption
Maximal consumption
0.10 µA
0.30 µA
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Ronda mastertech Technical Instructions

Ronda
Brand
Ronda
Model
mastertech
Type
Technical Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents