Avanti MOM9704 User manual

Avanti
Brand
Avanti
Model
MOM9704
Type
User manual

Avanti MOM9704 is a microwave oven bracket designed to mount your microwave oven on top of your refrigerator. It is compatible with Avanti microwave models MO7082MB, MO7191TW, MO7192TB, MO7103SST, and MO8003BT, as well as most compact, midsize, and counter-high Avanti refrigerators, excluding the SuperConductor models SHP1700W, SHP1701B, SHP1702SS, SHP2403B, and SHP2501B.

The bracket comes with all the necessary hardware, including screws, anchors, and lock pins. It is easy to install and can be done in just a few steps. Once installed, the bracket will securely hold your microwave oven in place, preventing it from tilting or falling.

Avanti MOM9704 is a microwave oven bracket designed to mount your microwave oven on top of your refrigerator. It is compatible with Avanti microwave models MO7082MB, MO7191TW, MO7192TB, MO7103SST, and MO8003BT, as well as most compact, midsize, and counter-high Avanti refrigerators, excluding the SuperConductor models SHP1700W, SHP1701B, SHP1702SS, SHP2403B, and SHP2501B.

The bracket comes with all the necessary hardware, including screws, anchors, and lock pins. It is easy to install and can be done in just a few steps. Once installed, the bracket will securely hold your microwave oven in place, preventing it from tilting or falling.

1
Installation & Assembly
Microwave Oven Bracket Installation Instruction
For use with the following Avanti models:
Microwaves – MO7082MB, MO7191TW, MO7192TB, MO7103SST& MO8003BT
Refrigerators – Can be used with all Compact, Midsize & Counterhigh models except the
SuperConductor models SHP1700W, SHP1701B, SHP1702SS, SHP2403B and SHP2501B
Parts List &
Hardware
Before you start this installation make sure you have all the parts listed below.
Read entire installation sheet before you start assembly of this item.
Part Number
Qty
Description
A
MOM9704
1
Mounting Bracket
B
9704-001
2
Locking Pin
C
9704-002
3
No. 8 x 5/8” Phillips Hex Head
Self Tapping Screw
D 9704-003 4 No. 8 x 1” Phillips Pan Head
Sheet Metal Screw
E
9704-004
4
Plastic Anchor (¼” x 1”)
Installation Procedures:
1) Bracket Configuration:
Holes (A), (B) and (C) are the existing holes in the upper part of the Metal bracket. Holes (D), (E), (F) and (G)
are also existing holes in the lower part of the Metal bracket.
See illustration #1.
Illustration #1
2) Installation of the upper side of the Metal bracket to the Microwave:
Place top of the bracket on the back of the microwave. Insert one of the (3) Phillips Hex Head Self Tapping
screws provided into pilot hole (A) then proceed installing the remaining (2) two Phillips Hex Head Self
Tapping screws into holes (B) and (C).Secure using a Phillips head screwdriver.
See illustration # 2.
2
Illustration # 2
3) Installation of the lower side of the Metal bracket to the Refrigerator:
Lay and center the Microwave oven (with bracket installed) on top of the refrigerator.
Flip down the lower part of the bracket.
Using the four (4) existing holes on the bracket as a guide, mark the locations where to drill the holes (D),
(E), (F) and (G). See illustration # 3.
Illustration # 3
4) Drilling the four holes to the Refrigerator:
After marking the locations of the four (4) holes, remove the Microwave oven and bracket from the top of
the refrigerator and proceed drilling the four (4) holes with a ¼” drill bit into the rear of the Refrigerator.
Be careful not to drill too deep and risk damaging the sealed system tubing or liner.
See illustration # 4.
3
Illustration # 4
5) Inserting the Plastic Anchors to the Refrigerator:
Insert the four (4) Plastic Anchors provided into the four (4) holes (step 5) in the back of the refrigerator.
See illustration # 5.
Illustration # 5
6) Completing the assembly:
Lay the Microwave oven with the metal bracket already installed on top of the refrigerator.
Align the four (4) holes of the lower part of the metal bracket to meet the four (4) plastic anchors installed in
previous step 6.
Attach the lower part of the metal bracket to the refrigerator.
Secure with the four (4) Phillips Pan Head Sheet Metal screws (provided) using a Phillips head screwdriver.
7) Safety features:
For your Safety, this metal bracket comes with two Lock Pins that will prevent the Microwave oven from
tilting back while in use. These two (2) Lock Pins (provided) can be lifted and removed to allow you to
clean the refrigerator top.
It is recommended to have both Lock Pins installed once the refrigerator is cleaned. See illustration # 6.
4
Microwave Oven
Refrigerator
Lock Pin
Illustration # 6
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Avanti MOM9704 User manual

Avanti
Brand
Avanti
Model
MOM9704
Type
User manual

Avanti MOM9704 is a microwave oven bracket designed to mount your microwave oven on top of your refrigerator. It is compatible with Avanti microwave models MO7082MB, MO7191TW, MO7192TB, MO7103SST, and MO8003BT, as well as most compact, midsize, and counter-high Avanti refrigerators, excluding the SuperConductor models SHP1700W, SHP1701B, SHP1702SS, SHP2403B, and SHP2501B.

The bracket comes with all the necessary hardware, including screws, anchors, and lock pins. It is easy to install and can be done in just a few steps. Once installed, the bracket will securely hold your microwave oven in place, preventing it from tilting or falling.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents