Eneo NTC-4151/PP Installation guide

Brand: Eneo

Model: NTC-4151/PP

Category: Security cameras

Type: Installation guide

Installation and Operating Manual

1/4” Network Day/Night Camera, Outdoor Housing, 22x Zoom

NTC-4151/PP

Contents

1. Safety Instructions ........................................................................................................................................................................................................................... 3

2. Introduction .....................................................................................................................................................................................................................................

2.1 General Description ................................................................................................................................................................................................................ 3

3. Network Camera Installation ............................................................................................................................................................................................................

3.1 Package Contents ................................................................................................................................................................................................................... 4

3.2 Operation Requirements ......................................................................................................................................................................................................... 4

3.3 Parts Name ............................................................................................................................................................................................................................. 5

3.4 Installation .............................................................................................................................................................................................................................. 5

3.4.1 Instillation 1 (Cable through the Wall with the Mount Base) ........................................................................................................................................ 6

3.4.2 Instillation 2 (Using the Conduit Knockout punched with Mount Base) ......................................................................................................................... 7

3.5 Connection ............................................................................................................................................................................................................................. 8

3.5.1 Colour Lead Wire & Colour Display Label .................................................................................................................................................................... 9

3.5.2 External Day/Night Control ......................................................................................................................................................................................... 9

3.5.3 RS-485 Connection .................................................................................................................................................................................................... 9

3.6 External A/D Key Control ....................................................................................................................................................................................................... 10

3.7 Setting up Network Connectivity ........................................................................................................................................................................................... 11

3.7.1 Allocating or Changing the Camera IP Address ........................................................................................................................................................ 11

3.8 Camera Control via NT Manager ........................................................................................................................................................................................... 12

3.8.1 NT Manager Main Menu ........................................................................................................................................................................................... 12

3.8.2 Logging on the Camera in the Network..................................................................................................................................................................... 13

4. Camera Adjustment

........................................................................................................................................................................................................................ 14

4.1 OSD Main Screen ................................................................................................................................................................................................................. 14

4.2 Main Menu ........................................................................................................................................................................................................................... 14

4.2.1 WB (White Balance) .................................................................................................................................................................................................. 14

4.2.2 AE (Auto Exposure) ................................................................................................................................................................................................... 15

4.2.3 BLC (Back Light Compensation) ............................................................................................................................................................................... 15

4.2.4 TITLE ....................................................................................................................................................................................................................... 15

4.2.5 DISPLAY ................................................................................................................................................................................................................... 16

4.2.6 CAM SET .................................................................................................................................................................................................................. 16

4.2.7 EFFECT .................................................................................................................................................................................................................... 16

4.2.8 PRESET .................................................................................................................................................................................................................... 17

5. Camera Control via Web Browser ...................................................................................................................................................................................................

5.1 Connecting camera with Web Browser .................................................................................................................................................................................. 18

5.2 Real-Time Monitoring ........................................................................................................................................................................................................... 19

5.3 NETWORK CAMERA Setting................................................................................................................................................................................................... 20

5.3.1 Video Setting ............................................................................................................................................................................................................ 20

5.3.2 Alarm Setting ........................................................................................................................................................................................................... 21

5.3.3 PTZ Setting .............................................................................................................................................................................................................. 24

5.3.4 System Setting ......................................................................................................................................................................................................... 26

5.4 Help...................................................................................................................................................................................................................................... 35

6. Troubleshooting ............................................................................................................................................................................................................................. 35

6.1 Preventive Maintenance........................................................................................................................................................................................................ 35

7. Speciﬁcations ................................................................................................................................................................................................................................ 36

8. Dimensional Drawings ...................................................................................................................................................................................................................

Betriebsanleitung

Installation and Operating Instructions

Mode d”emploi

Instrucciones de manejo

www.videor.com

1. Safety Instructions

• Read these safety instructions and the operation manual ﬁrst before you install and commission the camera.

• Keep the manual in a safe place for later reference.

• Protect your camera from contamination with water and humidity to prevent it from permanent damage.

Never switch the camera on when it gets wet. Have it checked at an authorized service center in this case.

• Never operate the camera outside of the speciﬁcations as this may prevent the camera functioning.

• Do not operate the cameras beyond their speciﬁed temperature, humidity or power ratings.

Operate the camera only at a temperature range of -10°C to +50°C and at a humidity of max. 90%.

• To disconnect the power cord of the unit, pull it out by the plug. Never pull the cord itself.

• Pay attention when laying the connection cable and observe that the cable is not subject to heavy loads, kinks, or damage and no moisture can get in.

• Do not attempt to disassemble the camera board from the dome.

• The warranty becomes void if repairs are undertaken by unauthorized persons. Do not open the camera housing.

• Installation, maintenance and repair have to be carried out only by authorized service centers.

Before opening the cover disconnect the unit from mains input.

• The ﬁtter is responsible for the system of protection being followed in accordance with the technical data, e.g. by sealing of the cable outlet with silicone.

• Contact your local dealer in case of malfunction.

• Only use original parts and original accessories from Videor E. Hartig GmbH.

• Do not use strong or abrasive detergents when cleaning the dome. Use a dry cloth to clean the dome surface.

In case the dirt is hard to remove, use a mild detergent and wipe gently.

• Do not open the camera housing in order to install the camera.

If you do open it, however, bear in mind that the front part of the housing is not secured by an arresting cable, i.e. that the heating supply is NOT ﬁtted

with a cord grip and can be torn away by the weight of the front part.

NOTE: This is a class A digital device. This digital device can cause harmful interference in a residential area; in this case the user may be required to take

appropriate corrective action at his/her own expense.

2. Introduction

2.1 General Description

The Day & Night AutoFocus Zoom color DSP Network Camera provides especially for closed circuit television (CCTV) and security surveillance application.

The Network Camera supports the operation through the network.

• 1/3” Super HAD Farb/SW CCD Sensor

• Sensitivity of 0.2Lux at F1.2 (Colour)

• Digital Noise Reduction (DNR)

• High and Low Speed Shutter Control (MES/ESC/DSS)

• On-screen Menu Control

• Camera Title Display

• Privacy Masking

• Mirror Function

• Motion Detection

• MPEG-4 Compression

• Image Frame Rate: Up to 25 Fr./sec. (720x576 pixel)

• Viewer for Monitoring, Recording and Conﬁguration

• Pre and Post Event Recording (in Client PC)

• Integrated Web Server: 10Base-T/100Base-TX

• All-In-One: Camera / Lens / Housing IP66

3. Network Camera Installation

Installation of the camera must be performed by qualiﬁed service personnel in accordance with all local national electrical and mechanical codes must perform instal

lation of the camera.

Perform the following steps to install the camera

3.1 Package Contents

• Camera

• Instruction Manual

• Connection Cable

• RJ-45 Coupler

• Install CD

• A/D Remote Controller (option)

3.2 Operation Requirements

RS-485

Kamera 1

Multiplexer

Video

Monitor

Kamera 2 Kamera 3 ...

J-Box

RS-485

LAN

Fernsteuerung DVR / VCR PC-Programm

LAN RS-485 VIDEO

3.3 Parts Name

Sunshield

AF D&N camera module

Mount base

Connection cable

Cable label

RJ-45 coupler

3.4 Installation

There are two ways of installing the camera.

1. Cable through the wall with mount base. 2. Using the conduit knockout punched with

the mount base.

3.4.1 Installation 1 (Cable through the Wall with the Mount Base)

A. Drill the mounting location, using the template sheet (or the bottom of the mount base) as a template.

B. Insert the plastic anchors into the hole which has just drilled.

C. Connect BNC cable and communication lines.

D. Fit the screw holes of the mount base into the plastic anchors.

E. Screw up the mount screws (T-20).

F. Adjust the camera suitably using the pan & tilt function, and fasten both the socket set screw „A” (1x) and torx lock screw „B” (2x) to ﬁx the camera.

Mount base

Wall

Template sheet

Plastic anchors (4x)

Torx screws (T-20)

M6.0 x 35.0 (4x)

Socket set screw

M5.0, L=5.0mm

Hexagon wrench

Torx lock screw (T-20)

3.4.2 Instillation 2 (Using the Conduit Knockout punched with Mount Base)

A. Drill the mounting location, using the template sheet (or the bottom of the mount base) as a template

B. Insert the plastic anchors into the hole which has just drilled.

C. Connect BNC cable and communication lines.

D. Fit the screw holes of the mount base into the plastic anchors.

E. Remove the conduit knockout punched for the cable entry.

F. Screw up the mount screws (T-20).

G. Adjust the camera suitably using the pan & tilt function, and fasten both the socket set screw „A” (1x) and torx lock screw „B” (2x) to ﬁx the camera.

Mount base

Wall

Template sheet

Plastic anchors (4x)

Torx screws (T-20)

M6.0 x 35.0 (4x)

Socket set screw

M5.0, L=5.0mm

Hexagon wrench

A conduit knockout punched

for the cable entry

Cable

Torx lock screw (T-20)

3.5 Connection

CAUTION: Do not connect the power cable until all other connections have been completed. if you complete the whole connection of cameras, then you

have to cut the extra cable.

Video (BNC)

Monitor

DVR / VCR

PC Program

Power connection

A/D key control

RS-485 connection

Day & night control

to local Internet networks

(blue)

(green)

(sky-blue)

(pink)

(black/white)

(orange)

3.5.1 Colour Lead Wire & Colour Display Label

Colour Description

Yellow jack Video OUT

Red jack DC IN

RJ-45 jack

LAN

Pink EXT-OUT

Sky-blue EXT-IN

Black GND

White GND

Blue RS-485 (–)

Green RS-485 (+)

Orange A/D KEY

Connection cable description

3.5.2 External Day/Night Control

GND (black)

EXT-OUT (pink)

EXT-IN (sky-blue)

External sensor switch ON/OFF

• DAY/NIGHT

Day: open

Night: closed

• EXT-OUT

Colour

B/W

Colour

Is connect to an external sensor to receive day/night detection signals.

NOTE: To validate the sensor inputs, select Function menu B/W mode the EXT.

3.5.3 RS-485 Connection

The Camera can be controlled remotely by an external device or control system, such as a control keyboard, using RS-485 half-duplex. Connect Market Rx+, Rx- to Tx+

and Tx- of the RS-485 control system.

RS-485

RS-485 (+)

(black)

RS-485 (–)

(pink)

A/D KEY (white)

A/D KEY2

(orange)

A/D KEY

AD KEY2

Remote controller

3.6 External A/D Key Control

External Controller Circuit Schematic

GND (black)

Remote controller (#92192)

3.7 Setting up Network Connectivity

3.7.1 Allocating or changing the camera IP address

Requirements:

• PC with ﬁxed IP address available.

• In WINDOWS XP, the ﬁrewall is disabled during IP allocation.

• CD with viewer software (NT Manager), setup software and client software available.

• Camera and PC are connected via a standard RJ-45 crossover cable in a network-compatible way.

• MAC address of the camera is known.

• Free IP address for camera is known.

• Name of the employed Ethernet adapter is known.

Step Action Menu path/menu item

1 Execute and/or save setup software and client software from the CD.

Result: The „Network System IP Setting Utility“ window is opened.

IP setting utility

2 Complete the MAC address of the camera. MAC address

3 Enter the IP address of the camera. IP address

4 Select the Ethernet adapter of the PC. Ethernet adapter

5 Log on the camera in the network.

Result: The IP address is allocated to the camera.

START

3.8 Camera Control via NT Manager

3.8.1 NT Manager Main Menu

The following ﬁgure and the table describe the main menu of the NT manager:

No. Designation Function

Display

Camera status

PTZ control

3 Display Camera list

Add group

Add camera

5 Display Search list

6 Display Monitoring image

7 Playback control

Additional information

The complete software description of the NT Manager can be found in the Help function of the NT Manager software.

Step Action Menu path/menu item

Install Viewer software from the CD.

2 Open the Viewer software.

User name:

admin

Password:

admin

Result: The Viewer software (NT Manager) is opened.

3 Add new group.

Result: The „Add new group„ window is opened.

4 Enter the name of the new group, and conﬁrm it.

Result: The new group is added to the camera list.

Add

Select the group in the camera list.

6 Add the new camera to the group.

Result: The „Add a new camera“ window appears.

Enter the name of the new camera.

Enter the IP address of the camera.

Host address

9 Register the camera.

Result: The new camera is added to the camera list, and integrated.

Add

10 Select the camera from the camera list, and drag it to a channel on the screen (Drag&Drop).

Result: The camera image appears on the screen.

3.8.2 Logging on the Camera in the Network

Requirements:

• PC with ﬁxed IP address available.

• CD with viewer software (NT Manager), setup software and client software available.

• Camera and PC are connected via a standard RJ-45 LAN cable in a network-compatible way.

• IP address of the camera is known.

4. Camera Adjustment

4.1 OSD Main Screen

(1) Camera title

(2) Status of the auto exposure

(3) Status of the auto white balance

(4) Status of the focus mode

(5) Status of the zoom position, brightness, or sharpness

(6) Status of the shutter speed

(7) Status of the iris

(8) Status of the AGC (auto gain control)

(9) Camera ID

4.2 Main Menu

4.2.1 WB (White Balance)

BLC

TITLE

DISPLAY / ALARM

CAM SET

EFFECT

PRESET

END

AWB: Auto white balance mode

INDOOR: Indoor white balance mode

OUTDOOR: Outdoor white balance mode

MANUAL: Manual mode. You can change R and B Gain manually.

For changing R and B gain, use „NEAR” and „FAR” key.

If you save the change, and push the „MENU” key.

WAWB: Wide range auto white balance mode

<WB>

AWB

INDOOR

OUTDOOR

MANUAL R/B

WAWB

END

22X NETWORK

AEAUTO

AWB

NORMAL

F1.6

0DB

84X CAM 01

4.2.2 AE (Auto Exposure)

4.2.3 BLC (Back Light Compensation)

<WE>

AUTO

IRIS PRI

SHUTTER PRI

AGC

MANUAL

END

DEFAULT: Default setting. Center weight BLC

ADJ TOP: You can adjust BLC Zone in left and/or top direction

ADJ BOTTOM: You can adjust BLC Zone in right and/or bottom direction.

LEVEL: You can adjust BLC level (0 ~ +90). Default value is 30.

OFF: BLC off

<BLC>

DEFAULT

ADJ TOP

ADJ BOTTOM

LEVEL

OFF

END

AUTO: Auto exposure mode (Iris, Shutter, AGC)

IRIS PRI: Iris priority auto exposure mode

SHUTTER PRI: Shutter priority auto exposure mode

AGC: Auto gain control on/off

MANUAL: Manual exposure mode (Iris, Shutter, and AGC)

LOW-SHUT: Display Low-Shutter mode (Mode can be changed in the preset menu.)

4.2.4 TITLE

TITLE

ABCDEFGHIJ

KLMNOPQRST

UVWXYZ0123

4 5 6 7 8 9 ( )

; . -

! ) - ,

CMD

< > S E

A. TITLE

B. Character Table

C. Command Line

: Move to left

: Move to right

< : Erase a left character

> : Erase a right character

S : Save title

E : End

4.2.5 DISPLAY

4.2.6 CAM SET

ID: Select the camera ID (1 ~ 255)

BPS: Select serial communication speed (2400 / 4800 / 9600 / 19200)

BRIGHTNESS: Select brightness level (0 ~ +90). Default value is 30.

SHARPNESS: Select sharpness level (0 ~ 15). Default value is 8.

DISTANCE: Select minimum distance in focus between camera and object.

(0.1 / 1.0 / 1.5 / 2.5 / 6.0 m)

MAX LOWSHUT: Select maximum Low-shutter value (x2, x4, x8, x16, x32, x60)

PROTOCOL: Select operating protocol.

COMMAND: Camera controlled by RS-232C command

FASTRAX: Fastrax protocol

PELCO-D: Pelco-D protocol

PELCO-P: Pelco-P protocol

SAVE PROTOCOL & BPS: Save protocol and BPS

NOTE 1: You can choose BPS menu appropriate for keyboard protocol.

NOTE 2: If you change BPS or PROTOCOL menu, you have to select PROTOCOL

& BPS menu. Although you change BPS or PROTOCOL menu, the

terms of change is not applied unless you select save PROTOCOL &

BPS menu.

BPS

BRIGHTNESS

SHARPNESS

DISTANCE

MAX LOW SHUT

PROTOCOL

SAVE PROTOCOL & BPS

END

DISP0: Display title and camera ID

DISP1: Display title, camera ID and zoom lens position

DISP2: Display all camera status

DISP: Off, On and push on (display on when any key is pressed)

ALARM MODE: Off, Preset 1~5, B/W (Zoom Preset and B/W setup by External-In)

DWELL TIME: 10, 20, … 120 sec. (Dwell time setup of Zoom Preset)

4.2.7 EFFECT

D-ZOOM: Digital Zoom on/off

NEGA/POSI: Select the Negative or Positive picture

B/W: Select Color & B/W picture or EXT mode

MIRROR: Select horizontal reverse picture

PIP: Picture In picture on/off

FREEZE: Select real and still picture

D/N: Day & Night mode on/off

CAUTION: Freeze mode is automatically off, when Zoom and Focus operation.

D-ZOOM

NEGA/POSI

B/W

MIRROR

PIP

FREEZE

D/N

END

DISP0

DISP1

DISP2

DISP

ALARM MODE

DWELL TIME

END

4.2.8 PRESET

FOCUS

INIT

LOAD

SAVE

SHOT

DNR

ZOOM PRESET

SET ZOOM PRESET

END

FOCUS: Select auto, manual, pushauto mode

INIT: Camera initialize mode selection (DEFAULT / PRESET)

LOAD: Load default or preset parameters of camera (DEFAULT / PRESET)

SAVE: Save preset camera parameters

SHOT: Select Normal, DIS, WDR, or Low-Shutter mode

DIS (digital image stabilization)

WDR (wide dynamic range)

Low-Shutter (low shutter speed mode)

DNR: Digital Noise Reduction mode on/off

ZOOM PRESET: Select Zoom Preset number

SET ZOOM PRESET: You can set zoom position of zoom preset.

CAUTION: In the WDR or Low-Shutter mode, AF performance and image

quality can be decreased.

DIS is operated on D-Zoom x2.

DNR is disabled in freeze, Low-Shutter and WDR mode.

WDR/EDR is not effective in Freeze status.

5. Camera Control via Web Browser

5.1 Connecting camera with Web Browser

Requirements:

• Camera and PC are connected via a standard RJ-45 LAN cable in a network-compatible way.

• Web browser (e.g. Internet Explorer) installed in the PC.

• Current version of ActiveX/HVC installed in the PC.

• IP address of the camera is known.

Step Action

1 Open the web browser.

Note: A separate web browser window must be opened for each camera.

2 Enter the IP address of the camera into the address line of the web browser.

Example: http://192.168.0.2

3 Enter user name (admin) and password (no entry).

4 Select login.

Result: The camera is connected with the web browser.

5.2 Real-Time Monitoring

The monitoring screen comes in four screen modes like D1, 640 x 480, 320 x 240, and 160 x 120. Users are allowed to select the most suitable one out of those

modes. Please, adjust the mode in accordance with your PC speciﬁcations and monitoring purposes.

In case of real-time monitoring with the Web Browser, one Network Camera will be connected to just one Web Browser. However, this case is not suitable for monitoring

various screens at the same time. If users are to monitor various images at the same time, please refer to the eVideoClient.

HTTP tunnel mode

When the screen is not indicated, check. (Notice: „unicast mode” only it is applied.)

If users are to control the volume of a microphone and speaker connected to a

user PC, they should adjust the user PC volume regardless of the microphone and

speaker volume control set in Network Camera.

5.3 NETWORK CAMERA Setting

The Network Camera setting is divided into video, alarm, PTZ and system settings. And the detailed screen will be provided for each setting.

5.3.1 Video Setting

The video setting is classiﬁed into Basic, MPEG-4. The Basic menu includes a setting menu for real-time monitoring. Its setting only is enough to complete a setting for

viewing the monitoring screen. The detailed setting menu is able to perform screen sizing, ﬁltering, compressibility, and brightness control.

5.3.1.1 Basic Setting

Image Appearance

Resolution

It enables users to determine a basic screen size when having an access through the Web Browser or PC program.

The screen size control comes in four modes like D1, 640x480, 320x240, and 160x128. Users can reset the selected screen size anytime while monitoring the screen

on a real-time basis.

Image ﬁlter

The image ﬁlter control enables users to reinforce the image quality in a strong or weak way. The default is „disabled”.

Compression

When it is necessary to adjust a smooth transmission status according to network situations, users can increase the compressibility to carry out the network trans

mission stably. On the other hand, when it is necessary to maintain a detailed monitoring screen by enhancing the image quality, users can do so by decreasing the

compressibility. In ease case, please adjust this function according to the network status and monitoring purposes. The default is 2000 (Kbps).

BCSH Adjust

Brightness

The screen brightness can be adjusted from 0 to 255 stages, and the default is 128. The brightness may differ depending on the equipment and PC monitor status.

Contrast

The screen contrast can be adjusted from 0 to 127 stages, and the default is 73. The contrast may differ depending on the equipment and PC monitor status.

Saturation

The screen saturation can be adjusted from 0 to 127 stages, and the default is 64. The saturation may differ depending on the equipment and PC monitor status.

Page is loading ...