LG LSW901P-B User manual

OWNER'S MANUAL

Color Video Network Camera

Please read this manual carefully before operating

your set and retain it for future reference.

MODEL

LSW900

LSW901

P/NO : MFL62591970 1011 (V2.0)

2

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

dangerous voltage within the product’s enclo-

sure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and mainte-

nance (servicing) instructions in the literature

accompanying the product.

FCC WARNING: This equipment may generate or use radio

frequency energy. Changes or modifications to this equip-

ment may cause harmful interference unless the modifica-

tions are expressly approved in the instruction manual. The

user could lose the authority to operate this equipment if

an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide rea-

sonable protection against harmful interference when the

equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interfer-

ence to radio communications.

Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be

required to correct the interference at his own expense.

• A suitable conduit entries, knock-outs or glands shall

be provided in the cable entries of this product in the

end user.

3

• Caution: Danger of explosion if battery is incorrectly

replaced. Replaced only with the same or equivalent

type recommended by the manufacturer. Dispose

of used batteries according to the manufacturer’s

instructions.

• Holes in metal, through which insulated wires pass,

shall have smooth well rounded surfaces or shall be

provided with brushings.

This Class A digital apparatus complies with Canadian

ICES-003.

Cet appareil numérique de la classe A est conforme à la

norme NMB-003 du Canada.

Warning: Do not install this equipment in a confined space

such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with the

National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environ-

ment this product may cause radio interference in which

case the user may be required to take adequate measures.

Warning: To reduce a risk of fire or electric shock, do not

expose this product to rain or moisture.

Caution: This installation should be made by a qualified

service person and should conform to all local codes.

Caution: To avoid electrical shock, do not open the cabi-

net. Refer servicing to qualified personnel only.

Caution: The apparatus shall not be exposed to water

(dripping or splashing) and no objects filled with liquids,

such as vases, shall be placed on the apparatus.

To disconnect power from mains, pull out the mains

cord plug. When installing the product, ensure that the

plug is easily accessible.

4

Disposal of your old appliance

1. When this crossed-out wheeled bin

symbol is attached to a product it means

the product is covered by the European

Directive 2002/96/EC.

2. All electrical and electronic products

should be disposed of separately from

the municipal waste stream via desig-

nated collection facilities appointed by

the government or the local authorities.

3. The correct disposal of your old appli-

ance will help prevent potential negative

consequences for the environment and

human health.

4. For more detailed information about

disposal of your old appliance, please

contact your city office, waste disposal

service or the shop where you pur-

chased the product.

EEE Compliance with Directive. (for Turkey only)

LG Electronics hereby declares that this/

these product(s) is/are in compliance with

the essential requirements and other relevant

provisions of Directive 2004/108/EC,

2006/95/EC, and 2009/125/EC.

European representative :

LG Electronics Service Europe B.V. Veluwezoom

15, 1327 AE Almere. The Netherlands

(Tel : +31-(0)36-547-8888)

5

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accor-

dance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the appa-

ratus. When a cart is used, use caution when moving

the cart/apparatus combination to avoid injury from

tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

Important Safety Instructions

6

Handling of the unit

Be careful not to spill water or other liquids on the unit. Be

cautious not to get combustible or metallic material inside

the body. If used with foreign matter inside, the device is

liable to fail or to get cause of fire or electric shock.

• Remove dust or dirt on the surface of the lens with a

blower.

• Use a dry soft cloth to clean the body. If it is very dirty,

use a cloth dampened with a small quantity of neutral

detergent then wipe dry.

• Avoid the use of volatile solvents such as thinners,

alcohol, benzene and insecticides.

They may damage the surface finish and/or impair the

operation of the device.

Operating and storage location

Avoid viewing a very bright object (such as light fittings)

during an extended period. Avoid operating or storing the

unit in the following locations.

• Extremely hot or cold places (operating temperature

from -10 °C to 50 °C, however, we recommend that the

unit be used within a temperature range from

0 °C to 45 °C)

• Damp or dust place

• Places exposed to rain

• Places subject to strong vibration

• Close to generators of powerful electromagnetic radia-

tion such as radio or TV transmitters.

Cautions for Safe Operation

7

Features ................................................................. 8

Part Names and Functions ................................... 9

Connections ........................................................12

Precautions .....................................................................12

Connection Overview .................................................12

Connecting Display Device .......................................13

Connecting Network ...................................................13

Connecting Power Source .........................................14

Connecting RS-485 Device ........................................15

Connecting Alarm Device ..........................................15

Connecting Microphone and Speaker Device ...16

Mounting the camera .................................................17

Operation and settings ......................................18

Before using the system .............................................18

Recommended PC Requirements ...........................18

Accessing the LG IP device ........................................19

LG Smart Web Viewer Overview ..............................20

Conguring the LG IP camera ..................................24

OSD Menu Setup...........................................................51

Troubleshooting .................................................63

Open source software notice .............................66

Specication ....................................................... 69

Contents

8

Features

The LG Color Video IP Camera is designed to use on an

Ethernet network and must be assigned an IP address to

make it accessible.

This manual contains instructions on how to install and

manage the LG Color Video IP Camera in your networking

environment.

Some knowledge of networking environments would be

beneficial to the reader.

Should you require any technical assistance, please contact

authorized service center.

• Dual H.264 Stream for single Video Input

• Multi-Codec (H.264, MJPEG) Streaming

• Intelligent Video Analysis (Option)

• PoE (Power over Ethernet) Support (802.3af )

• 3 Power (AC 24 V, DC 12 V, PoE) Support

• Audio Support (G.711, G.726 Full Duplex)

• Pre/Post Alarm Support

• Remote Pan/Tilt/Zoom Control (RS-485 support)

• High resolution and high sensitivity with a 6 mm

Vertical Double Interline CCD.

• Auto White Balance

• Day & Night function

• WDR (Wide Dynamic Range) is available

Features Chart

This table shows the differences between the models.

Use LSW901 is used for the description, operations and

details provided in this user manual.

Models LSW900 LSW901

VCA No Yes

PTZ Yes Yes

PRESET Yes Yes

Fan Fail

Notification

Yes Yes

Fan & Heater

Temperature

No No

9

 a b cd

 e

a Lens mount cap

The lens mount of the camera is covered using a cap

to protect it. Remove the lens cap covering the lens.

b Flange-back adjustment lever

c Lens iris output connector (LENS)

This 4- pin connector is used to send the Iris control

signal and power supply to an auto-iris type lens.

d ALC Lens setting switch

• VIDEO: When you attach an Auto Iris lens requir-

ing the video control signal, please put this

switch in the VIDEO position.

• DC: When you attach an Auto Iris lens requiring

the DC control signal, please put this switch in

the DC position.

e Camera installation bracket

The bracket can be fixed at the top or bottom of the

camera.

Part Names and Functions

10

Part Names and Functions

 f g h i

 jkl m

f External device connectors

• TRX +/TRX - Terminals: Connect to an external

controller of RS-485 format.

• A IN(R)/A IN (Sensor input) Terminals:

Provides physical interface for sensor.

• A OUT(R)/A OUT (Relay output) Terminals:

Provides physical interface for Alarm/Relay.

g RESET button

Push the button more than 3 seconds, this would

restore the factory default settings.

h Power indicator

Lights when the camera is powered.

i Power input terminal

Connects to a DC 12 V or AC 24 V power supply using

proper cables.

j AUDIO OUT (Line Level Output)

Connect to an active speaker with a built-in amplifier.

11

k VIDEO OUT

Supplies analog video signal (composite) to the con-

nected device.

l AUDIO IN (Line Level Input)

Input for a mono microphone, or a line-in mono

signal.

m ETHERNET/POE Port

Connects to a PC or a network via a hub with a

10 BASE-T/100 BASE-TX cable attached RJ-45 connec-

tor.

Note:

Power over Ethernet (PoE) is a technology that inte-

grates power into a standard LAN infrastructure. It

enables power to be provided to the network device,

such as a network camera, using the same cable as

that used for network connection. It eliminates the

need for power outlets at the device locations and

enables easier application of uninterruptible power

supplies (UPS).

Part Names and Functions

12

Precautions

• Be sure to switch off the unit before installation and connection.

• The installation should be made by qualified service personnel or system installers.

• Do not expose the power and connection cables to moisture, which may cause damage to the unit.

Connection Overview

RS-485

Unit

PoE Device

(IEEE802.3af )

PoE Device

(IEEE802.3af)

RS-485

Unit

Connections

13

Connecting Display Device

Connect the video signal between the IP camera and the

monitor.

Connecting Network

You can control and monitor the system via network. With

the remote control (monitoring), you can change the sys-

tem configuration or monitor the image via network. After

the installation, check the network settings for the remote

control and monitoring work.

Connect the IP camera to your network using a standard

RJ-45 network cable as shown below.

PoE Device

(IEEE802.3af )

Router

Broadband

Service

Broadband

Service

Broadband

Service

Broadband

Service

Router

PoE Device

(IEEE802.3af)

Connections

14

Connecting Power Source

Connect power, using one of the methods listed below:

To use the power adapter

Connect a DC 12 V / AC 24 V power source to the

power input terminal as shown below.

1. Remove the insulation on the power cable as

illustrated.

2. Attach the terminal tips.

3. Connect to the DC 12 V / AC 24 V UL Listed, Class

2 Power Supply only on the unit.

PoE Device

(IEEE802.3af )

To use the PoE (Power over Ethernet) device

Connect the PoE cable to the LAN port on the unit.

You must use the “IEEE802.3af” standard PoE device.

PoE Device

(IEEE802.3af )

PoE Device

(IEEE802.3af)

Note:

If the camera doesn't work properly after connect PoE

device, please check if the PoE device is supplying enough

power.

Connections

15

Connecting RS-485 Device

Use these ports to connect an external device of RS-485

format.

RS-485

Unit

TRX +

TRX -

RS-485

Unit

Connecting Alarm Device

Alarm terminals are used to connect the alarm (relay)

devices such as sensors, door switches, etc.

A IN(R)/A IN (Sensor Input )

Connect the sensor device to the sensor input

terminal.

RS-485

Unit

TRX +

TRX -

Sensor

Device

Connections

16

A OUT(R) / A OUT (Relay Output)

Connect the alarm (relay) device to the relay output

terminal. Alarm signal is outputted at an event

occurrence.

RS-485

Unit

TRX +

TRX -

Alarm (Relay)

Device

Note:

The Photo MOS Relay is rated for 100 mA at 20 V DC or

100 mA at 28 V AC.

Connecting Microphone and

Speaker Device

Optionally connect an active speaker and/or external

microphone with a built-in amplifier.

Note:

Keep the microphone away from the speaker to avoid

howling.

Connections

17

Connections

Mounting the camera

The mounting bracket can be secured on either the top or

bottom of the camera. Use the same set of screws to attach

the mounting bracket on the camera.

Note:

If using a camera mounting bracket, select a location that

is strong enough to bear the full weight of the camera and

the mounting bracket for long periods, and install the cam-

era and mounting bracket securely.

18

Operation and settings

Before using the system

• Before using the LG IP device make sure the connec-

tions are correct and verify whether proper power

supply is used.

• Check the connections of the LG IP device for the cor-

rect conditions.

• Check that the LG IP device is(are) connected to the

network and that power is supplied.

• Once the connections are made you need to install the

LG client program to the PC from which you want to

access the device. The LG Smart Web Viewer program

is automatically installed when you connect the LG IP

device. The LG Smart Station and the LG Smart Web

Viewer program are the network program of the LG

Video Server and the LG IP cameras.

• To view streaming video in Internet Explorer, set your

browser to allow ActiveX controls. If you find this mes-

sage “This website wants to install the following add-

on: ‘IPCam_Streamer.cab’ from ‘LG ELECTRONICS INC’”,

Click the yellow bar and install LG Smart Web Viewer

Program on your computer.

• The Layouts and the Live view pages may differ with

different OS (Operating Systems) and Web Browsers.

• Care needs to be taken not to run any other applica-

tions when the Client Program is running as it may

cause memory shortage.

Recommended PC Requirements

The LG IP device can be used with most standard operating

systems and browsers.

Items Requirements

Operating

System

Windows XP Professional or above

CPU

Intel Core2 Quard Q6700 (2.66GHz) or

above

Web Browser Microsoft Internet Explorer 6.0 or higher

DirectX DirectX 9.0 or above

Memory 2 GB or above RAM

Graphics Card 256 MB or above Video RAM

Resolution 1 280 x1 024 (with 32bit color) or higher

19

Operation and settings

Accessing the LG IP device

You can access the LG IP device by following the below

steps.

1. Copy the IP Utility to your PC

1.1 Insert the Client Program CD.

1.2 Find and Copy IP Utility folder to your PC.

2. Discover LG IP device using the IP Utility

The IP Utility can automatically discover and display

LG IP devices on your network. The IP Utility shows the

MAC address, IP address, Model name and so on.

Note:

The computer running the IP Utility must be on the

same network segment (physical subnet) as the LG IP

device.

2.1 Run the IP Utility program.

2.2 Click the [Search] icon or select the [Search]

option in the Device search menu.

After a few seconds the found LG IP devices gets

displayed in the IP Utility window.

3. Logging in to the LG Smart Web Viewer

The LG Smart Web Viewer can be used with most

web browsers. The recommended browser is Internet

Explorer with Windows.

3.1 Run the IP Utility and find the LG IP devices.

3.2 When the LG IP devices appear in the IP Utility

window, double-click IP address or right click on

the same IP address and select "Connect to Web

Page" to start the LG Smart Web Viewer. When

accessing the LG Smart Web Viewer, the authenti-

cation dialog appears on the screen.

3.3 Enter the user name and password. (Note that the

default administrator user name and password

are “admin”.)

3.4 Click the [OK] button and then the LG Smart Web

Viewer is displayed in your browser.

Notes:

• You can also access the LG Smart Web Viewer as

shown below.

3.1 Start your Web browser.

20

Operation and settings

3.2 Enter the IP address of the LG IP device in

the address bar of the browse.

3.3 Enter the user name and password set by the

administrator.

3.4 Click the [OK] button and then the LG Smart

Web Viewer is displayed in your browser.

• The LG Smart Web Viewer needs more time to dis-

play it according to the network conditions.

• If the login window is not displayed, check the

pop-up blocker. If you set the pop-up blocker, the

login window is not displayed. You must allow

the pop-ups.

• If you connect the LG Smart Web Viewer for

the first time, the Security Warning window is

displayed to install the LG Smart Web Viewer pro-

gram. You must install the LG Smart Web Viewer

program for using the LG IP device.

• If your computer or network is protected by a

proxy or firewall, the proxy or firewall settings

can prevent the LG Smart Web Viewer program.

Change the proxy or firewall settings to activate

the LG Smart Web Viewer program.

LG Smart Web Viewer Overview

Page is loading ...

LG LSW901P-B User manual

LG LSW901P-B User manual

Related papers

Other documents