2. Epson
  3. TM-L90 Plus-i KDS Liner-free Compatible
TM-L90 Plus-i KDS Liner-free Compatible

Epson TM-L90 Plus-i KDS Liner-free Compatible, TM-T88V-i KDS with VGA or COM, TM-U220-i KDS with VGA or COM User manual

  • Hello! I am an AI chatbot trained to assist you with the Epson TM-L90 Plus-i KDS Liner-free Compatible User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is bump and print functionality?
    How do I enable bump and print functionality?
    Can I customize the header and footer text on bump and print labels?
    What special characters can I use in the header and footer text?
    How do I change the text alignment in the header and footer?
    Can I make the text bold and double-width?
111-38-QUM-012
Rev 2.30
Bump and Print
About this Guide
This guide consists of 2 sections:
• Overview
• How to Configure - A procedure that can be followed to configure this in a KDS
system. This guide assumes you already have a Single or Multi-Station system
setup as described in the Epson KDS Quick Start Guides.
This guide is relevant for:
KDS FW: v2.30 and above
KDS Utility (Windows): v2.3.1.0 and above
Overview
A KDS printer can be configured to bump and print labels for individual items and/or
entire orders. This can be configured individually for any KDS printer in the system.
Bump and Print
Quick User Manual
111-38-QUM-012
Rev 2.30
How to Configure
This procedure can be followed to configure bump and print functionality in any Epson
KDS system.
Step 1: Enable the bump and print functionality
1. Select Devices
2. Select the KDS printer you wish to configure to bump and print.
3. Select “Print Item on Bump” and/or “Print Tile on Bump”
4. Click Apply KDS Settings.
The KDS printer is now configured for bump and print functionality.
Bump and Print
Quick User Manual
111-38-QUM-012
Rev 2.30
Appendix – Custom Header/Footers
Custom header/footer text can be configured to print on the bump and print labels.
1. Select Setup
2. Select Site Wide Settings
3. In the Printing on Bump section, the headers can be configured.
These fields can contain any simple text or ESC/POS commands. If you want to add any
extra commands, there is some special processing done that allows non-ASCII characters
to be added to the text. The following sequences are all supported:
• \n - line feed
• \t - tab
• \v - vertical tab
• \xnn - hexadecimal code
• \0nnn - octal code
• \\ - backslash
• Any other character after the ‘\’ will just be itself.
Bump and Print
Quick User Manual
111-38-QUM-012
Rev 2.30
Example: Command to change whether text is left/center/right justified is ESC a n, and
the ESC character is \033. The following command sequence will center the header.
\033a\01HEADER\n------\n\033a\0
This translates as ESC a 1 HEADER LF ------ LF ESC a 0, and it will print as:
HEADER
------
Note: Extra LF was added in there because the ESC a n command only works at the start
of a line.
Example: To make the characters bold and double-width as well:
\033!\050\033a\01HEADER\n------\n\033a\0\033!\0
This translates as ESC ! 0x28 ESC a 1 HEADER LF ------ LF ESC a 0 ESC ! 0x00.
WARNING: Both the \xnn and \0nnn sequences can take any number of digits after
them. This means that, to do the ‘ESC 2’ command, you need to use \033\062 or
something similar, because \0332 will be read as a single character.
/