Pelco PP200 Parapet Mount Installation guide

Brand: Pelco

Model: PP200 Parapet Mount

Category: Security camera accessories

Type: Installation guide

Important Safety Instructions

Prior to installation and use of this product, the following warnings should be observed.

1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.

2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approved materials.

3. Use only installation methods and materials capable of supporting four times the maximum specified load.

4. Use stainless steel hardware to fasten the mount to outdoor surfaces.

5. To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply sealant around the bolt holes between the mount and

mounting surface.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of electric shock is present

within this unit.

This symbol indicates that there are important operating and maintenance instructions in the

literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.

Description

Pelco’s PP200 parapet adapter mount has been engineered to eliminate the expense and hazard of installing and servicing surveillance accessory equipment

mounted on parapets. The PP200 is designed to attach to the PA2000, PA2010, or other pan/tilt adapters.

The PP200 mounts on the inside of a parapet that is at least 18 inches (45.72 cm) high. The mount rotates 360 degrees, allowing the equipment to be

installed and serviced safely from the rooftop. The mount’s unique design allows it to be positioned anywhere on the parapet, including corners. This

adapter mount will support up to 175 pounds (78.75 kg).

Pelco Parts List

The PP200 Parapet Mount kit contains the following items:

User-Supplied Parts

Sixteen fasteners to secure the PP200 to the parapet wall (such as lag screws or concrete fasteners) are not supplied. At a minimum, 3/8-inch diameter

fasteners are recommended.

Qty Description

1 PP200 parapet adapter

1 Flange and tube assembly

2 Wall mounting brackets (1 upper and 1 lower with strap)

2 Threaded U-bolts, 5/16-18-UNC x 3.5-inch I.D. with flat washers and nuts

1 Adapter mounting hardware

4 Hex nuts, 5/16-18

4 Split lock washers, 5/16

4 Hex screws, 5/16-18 x 1-inch

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

INSTALLATION

PP200 Parapet Mount

C247M-B (1/11)

2 C247M-B (1/11)

Installation

Refer to Figure 1 to perform the following steps:

1. Slip the upper wall mounting brackets onto the tube assembly. Do not tighten the upper mounting bracket U-bolt at this time.

2. Install the lower wall mounting bracket:

a. Slip the lower mounting bracket with the strap (attached to the adapter) onto the tube assembly.

b. Seat the bottom of the tube against the strap.

c. Tighten the lower mounting bracket U-bolt until it is snug (do not overtighten).

3. Hold the PP200 adapter mount against the parapet, and position it as far down as possible so the gusset clears the top of the parapet by 1 or 2 inches.

4. Slide the upper mounting bracket up to the edge of the parapet or as close to the edge as practical.

5. Tighten the upper mounting bracket U-bolt until it is snug (do not overtighten), and then mark the drill pattern through the mounting holes on both

brackets.

6. Drill the mounting holes and insert 16 fasteners (not supplied) to secure the mount to the parapet.

7. After the PP200 mount is attached securely to the parapet, loosen the two U-bolts so the tube can rotate freely.

8. Attach the mount for the equipment (for example, PA2000, PA2010, or other mount) to the top of the PP200 adapter mount, and then install the

equipment using the hex screws, hex nuts, and four split lock washers (not supplied).

9. Rotate the equipment over the parapet and lock securely into position by tightening the two U-bolts.

NOTE: When service of equipment is required, simply loosen the two U-bolts and rotate the equipment for easy accessibility.

Figure 1. PP200 Installation

Flange with Tube Assembly

Upper Wall Mounting Bracket

Lower Wall Mounting Bracket

Threaded U-Bolts

16 Fasteners (not supplied)

C247M-B (1/11) 3

Specifications

PP200 Parapet adapter mount for use with PA2000, PA2010, or other pan/tilt adapters; position equipment anywhere on the

parapet, including corners; minimum parapet height is 18 inches (45.72 cm)

Positioning Adjustment 360°

Suggested Mounting Method Secure to parapet with 16 suitable fasteners (minimum 3/8-inch diameter recommended, not supplied)

Adapter Mounting Method Four 5/16-inch hex screws, hex nuts, and split lock washers (supplied)

Maximum Load 175 lb (78.75 kg)

Construction Aluminum

Finish Polyester powder coat

Weight 11 lb (4.95 kg)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.

3.31

(8.41)

2.50

(6.35)

11.00

(27.94)

27.00

(68.50)

19.50

(49.53)

5.50

(13.97)

15.00

(38.10)

5.00

(12.70)

TYP

2.81

(7.14)

TYP

0.50

(1.27)

6.00

(15.24)

Ø0.38 (Ø0.97), 8X

Ø1.375 (3.48), 1X

Ø0.344 (Ø0.848) 1/4-20

PEM NUT, 4X

1.59 (4.04)

1.50 (3.81)

0.795 (2.02)

1.59 (4.04)

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union

regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

Pelco by Schneider Electric 3500 Pelco Way Clovis, California 93612-5699 United States

USA & Canada Tel (800) 289-9100 Fax (800) 289-9150

International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120

www.pelco.com

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in

material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years:

– Fiber optic products

– Unshielded Twisted Pair (UTP) transmission products

– CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and

MC3651H-2X camera models

• Three years:

– Pelco-designed fixed network cameras and network dome cameras with

Sarix

™

technology.

– Pelco-branded fixed camera models (CCC1390H Series, C10DN Series,

C10CH Series, and IP3701H Series)

– EH1500 Series enclosures

– Spectra

IV products (including Spectra IV IP)

– Camclosure

Series (IS, ICS, IP) integrated camera systems

– DX Series digital video recorders (except DX9000 Series which is covered

for a period of one year), DVR5100 Series digital video recorders, Digital

Sentry

Series hardware products, DVX Series digital video recorders, and

NVR300 Series network video recorders

– Endura

Series distributed network-based video products

– Genex

Series products (multiplexers, server, and keyboard)

– PMCL200/300/400 Series LCD monitors

– PMCL5xx Series FHD monitors

• Two years:

– Standard varifocal, fixed focal, and motorized zoom lenses

– DF5/DF8 Series fixed dome products

– Legacy

Series integrated positioning systems

– Spectra III

™

, Spectra Mini, Spectra Mini IP, Esprit

, ExSite

, and PS20

scanners, including when used in continuous motion applications.

– Esprit Ti and TI2500 Series thermal imaging products

– Esprit and WW5700 Series window wiper (excluding wiper blades).

– CM6700/CM6800/CM9700 Series matrix

– Digital Light Processing (DLP

) displays (except lamp and color wheel). The

lamp and color wheel will be covered for a period of 90 days. The air filter is

not covered under warranty.

– Intelli-M

eIDC controllers

• One year:

– Video cassette recorders (VCRs), except video heads. Video heads will be

covered for a period of six months.

•Six months:

– All pan and tilts, scanners, or preset lenses used in continuous motion

applications (preset scan, tour, and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of

Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid

to a Pelco designated location. Repairs made necessary by reason of misuse,

alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss

resulting from the specific use or application made of the Products. Pelco’s liability

for any claim, whether based on breach of contract, negligence, infringement of

any rights of any party or product liability, relating to the Products shall not exceed

the price paid by the Dealer to Pelco for such Products. In no event will Pelco be

liable for any special, incidental, or consequential damages (including loss of use,

loss of profit, and claims of third parties) however caused, whether by the

negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may

also have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or

(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the

following information:

1. Model and serial number

2. Date of shipment, P.O. number, sales order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product that does not fall under

the warranty conditions stated above, please include a written explanation with

the product when returned.

Method of return shipment shall be the same or equal to the method by which the

item was received by Pelco.

RETURNS

To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100

or (559) 292-1981 to obtain an authorization number (CA number if returned for

credit, and RA number if returned for repair) and designated return location.

All merchandise returned for credit may be subject to a 20 percent restocking and

refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned

CA or RA number and freight should be prepaid.

2-10-10

C247M-B (1/11)

REVISION HISTORY

Manual # Date Comments

C247M-A 7/95 Original version.

11/99 Revised to new format.

C247M-B 1/11 Revised installation instructions, Figure 1, and dimension drawing. Also applied new format and updated the warranty.

Product specifications and availability are subject to change without notice.

Pelco PP200 Parapet Mount Installation guide

Brand: Pelco

Model: PP200 Parapet Mount

Category: Security camera accessories

Type: Installation guide

Download PDF

report

Pelco PP200 Parapet Mount Installation guide

Pelco PP200 Parapet Mount Installation guide

Related papers

Other documents