Extron Quantum Connect User manual

User Guide

Quantum Control Software

Videowall Processors

Quantum Elite Control Software

Quantum Connect Control Software

68-1883-01 Rev. D

07 14

Safety Instructions

Safety Instructions • English

WARNING: This symbol, , when used on the product, is intended to

alert the user of the presence of uninsulated dangerous voltage within the

product’s enclosure that may present a risk of electric shock.

ATTENTION: This symbol, , when used on the product, is intended

to alert the user of important operating and maintenance (servicing)

instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide, part number 68-290-01, on the Extron website,

www.extron.com.

Instructions de sécurité • Français

AVERTISSEMENT: Ce pictogramme, , lorsqu’il est utilisé sur le

produit, signale à l’utilisateur la présence à l’intérieur du boîtier du produit

d’une tension électrique dangereuse susceptible de provoquer un choc

électrique.

ATTENTION: Ce pictogramme, , lorsqu’il est utilisé sur le produit,

signale à l’utilisateur des instructions d’utilisation ou de maintenance

importantes qui se trouvent dans la documentation fournie avec le

matériel.

Pour en savoir plus sur les règles de sécurité, la conformité à la réglementation,

la compatibilité EMI/EMF, l’accessibilité, et autres sujets connexes, lisez les

informations de sécurité et de conformité Extron, réf. 68-290-01, sur le site

Extron, www.extron.com.

Sicherheitsanweisungen • Deutsch

WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer

darauf aufmerksam machen, dass im Inneren des Gehäuses dieses

Produktes gefährliche Spannungen herrschen, die nicht isoliert sind

und die einen elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in der

im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise

zur Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,

EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in

den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer

68-290-01) auf der Extron-Website, www.extron.com.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,

avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del

producto, lo que puede representar un riesgo de descarga eléctrica.

ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa

al usuario de la presencia de importantes instrucciones de uso y

mantenimiento recogidas en la documentación proporcionada con el

equipo.

Para obtener información sobre directrices de seguridad, cumplimiento

de normativas, compatibilidad electromagnética, accesibilidad y temas

relacionados, consulte la Guía de cumplimiento de normativas y seguridad de

Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.

Инструкция по технике безопасности • Русский

ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан

на продукте, предупреждает пользователя о наличии

неизолированного опасного напряжения внутри корпуса

продукта, которое может привести к поражению

электрическим током.

ВНИМАНИЕ: Данный символ, , если указан на продукте,

предупреждает пользователя о наличии важных инструкций

по эксплуатации и обслуживанию в руководстве,

прилагаемом к данному оборудованию.

Для получения информации о правилах техники безопасности,

соблюдении нормативных требований, электромагнитной

совместимости (ЭМП/ЭДС), возможности доступа и других

вопросах см. руководство по безопасности и соблюдению

нормативных требований Extron на сайте Extron: www.extron.com,

номер по каталогу - 68-290-01.

Chinese Simplified（简体中文）

警告：产品上的这个标志意在警告用户该产品机壳内有暴露的危险电压，

有触电危险。

注意：产品上的这个标志意在提示用户设备随附的用户手册中有

重要的操作和维护(维修）说明。

关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍

使用的特性等相关内容，敬请访问 Extron 网站 www.extron.com，参见

Extron 安全规范指南，产品编号 68-290-01。

Chinese Traditional（ )

警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著

可能會導致觸電之風險的未絕緣危險電壓。

注意 若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有重

要的操作和維護（維修）説明。

有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資

訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規

遵守手冊》，準則編號 68-290-01。

Japanese

警告: この記号が製品上に表示されている場合は、筐体内に絶縁されて

いない高電圧が流れ、感電の危険があることを示しています。

注意: この記号が製品上に表示されている場合は、本機の取扱説明書

に記載されている重要な操作と保守( 整備 )の指示についてユーザーの注

意を喚起するものです。

安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に

ついては、エクストロンのウェブサイト www.extron.com より『 Extron Safety

and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ください。

Korean

경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는

접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을

경고합니다.

주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와

있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.

안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에

대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및

규제 준수 안내서, 68-290-01 조항을 참조하십시오.

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part15 of the FCC rules. The ClassA limits provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause interference. This interference must be corrected at

the expense of the user.

NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility,

accessibility, and related topics, see the “Extron Safety and Regulatory Compliance

Guide” on the Extron website.

Copyright

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks

®

, registered service marks

(SM)

, and trademarks

(TM)

are the property of

RGBSystems, Inc. or Extron Electronics:

Registered Trademarks

(®)

AVTrac, Cable Cubby, CrossPoint, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, GlobalViewer, Hideaway, Inline, IPIntercom,

IPLink, Key Minder, LockIt, MediaLink, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch,

SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VersaTools, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, and XTP Systems

Registered Service Mark

(SM)

: S3 Service Support Solutions

Trademarks

(

™

)

AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), Auto-Image, CDRS (Class D Ripple Suppression), CableCover,

DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), DriverConfigurator, DSPConfigurator, DSVP (Digital Sync

Validation Processing), EQIB, FastBite, FOXBOX, Global Configurator, IP Intercom HelpDesk, MAAP, MicroDigital, ProDSP, QS-FPC (QuickSwitch

Front Panel Controller), Scope-Trigger, SIS, Simple Instruction Set, Skew-Free, SpeedNav, Triple-Action Switching, XTRA, ZipCaddy, ZipClip

Conventions Used in this Guide

Notifications

The following notifications are used in this guide:

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

TIP: A tip provides a suggestion to make working with the application easier.

Software Commands

Commands are written in the fonts shown here:

^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C

[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]

E X! *X1&* X2)* X2#* X2! CE}

NOTE: For commands and examples of computer or device responses mentioned

in this guide, the character “0” is used for the number zero and “O” is the capital

letter “o.”

Computer responses and directory paths that do not have variables are written in the font

shown here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and field names are

written in the font shown here:

From the File menu, select New.

Click the OK button.

Specifications Availability

Product specifications are available on the Extron website, www.extron.com.

Contents

Introduction.........................................................1

About this Guide ................................................. 1

Overview of the Quantum Control Software ........ 1

Features ............................................................. 2

Installation and Operation ...................................3

Requirements ..................................................... 3

System Requirements ..................................... 3

Network Requirements ................................... 4

Image Processing Hardware ........................... 4

Software Installation............................................ 4

Configuring the Hardware ................................... 5

Connecting to a Quantum Elite or

Quantum Connect ......................................... 5

Setting the IP Address of the Computer .......... 6

Testing the Ethernet Link................................. 6

Using the Quantum Control Software ................. 7

Starting and Exiting the Quantum Control

Software ........................................................ 7

Main Application Window ............................... 8

Starting a New Project .................................... 9

Loading an Existing Project ........................... 10

Saving a Project ............................................ 10

Using Auto-backup ....................................... 10

System Conﬁguration ........................................12

Choosing a Display Processor .......................... 12

Assigning a Name to a Quantum

Processor .................................................... 14

Layout Configuration ........................................ 14

Choosing a Display Layout ........................... 14

Designing a New Layout ............................... 17

Modifying an Existing Layout......................... 18

Importing a Layout ........................................ 18

Deleting a Layout .......................................... 18

Arranging Layouts......................................... 19

Restoring Default Layouts ............................. 19

Communications Setup .................................... 19

Configuring Serial Ports ................................ 20

XML Device Drivers ....................................... 21

Setting Up Sources .......................................... 21

Creating Quantum Source Types and

Source Definitions ........................................ 22

Deleting Source Definitions ........................... 23

Refreshing Source Data ................................ 23

Source Parameters ....................................... 24

Defining EDID ................................................... 38

Selecting an EDID ......................................... 38

Capturing an EDID (HDMI Displays Only) ...... 40

Creating a Project .............................................41

Working with Scenes ........................................ 41

Scene Design Task ....................................... 41

Creating a New Scene .................................. 42

Copying an Existing Scene ........................... 43

Deleting a Scene .......................................... 43

Changing Scene Properties .......................... 43

Scene Commands ........................................ 44

Changing the Order of Scenes and Scene

Navigation ................................................... 46

Working with Windows ..................................... 46

Adding Windows to the Window Palette ....... 48

Adding a Docked Window to a Scene .......... 48

Adding or Changing a Source for a

Window ....................................................... 49

Deleting a Window ........................................ 50

Moving and Resizing a Window .................... 50

Selecting the Window Style (Quantum Elite

Models Only) ............................................... 52

Changing the Zoom Properties ..................... 55

Changing the Layer of a Window .................. 58

Changing the Virtual Display Properties ......... 59

Quantum Control Software • Contents v

Viewing a Project ..............................................61

Using the Scene Control ................................... 61

Run View and Design View ........................... 61

Full Screen Mode .......................................... 62

Creating a Default Layout.............................. 63

Customizing the Layout ................................ 63

Using the Bitmap Manager ........................... 66

Using Auto Play ................................................ 68

Changing the Order of Scenes ...................... 68

Changing the Display Time for a Scene ........ 68

Starting and Stopping the Project ................. 69

Changing the Playback Speed ...................... 69

Serial Commands ..............................................70

Control of External Devices ............................... 70

Format of External Control Strings ................ 71

Remote Control of a Project ............................. 72

R-type Message Format ............................... 72

Command Symbol Definitions ....................... 73

Command Table ............................................... 74

Examples of R-type Messages ..................... 78

Merge Scene Commands ............................. 79

ASCII Character Chart ...................................... 80

Access Control ..................................................81

Login Procedure ............................................... 81

Enabling and Disabling Access Control ............. 82

Changing Level Passwords............................... 83

Reference Information .......................................84

Modifying Window Styles .................................. 84

Overview ...................................................... 84

Locating and Opening the XML File .............. 85

Overview of the Style Tag .............................. 86

Modifying an Existing Style ........................... 88

Adding a New Style ...................................... 88

Working with Merge Scenes ............................. 90

Merge Scene Overview ................................. 90

Defining Displays or Display Groups .............. 90

Programming Subscenes ............................. 91

IP Addressing ................................................... 95

What is an IP Address?................................. 95

Choosing IP Addresses ................................ 95

Quantum Control Software • Contents vi

Introduction

This section gives an overview of the guide and features of the Quantum Elite Control

Software and Quantum Connect Control Software. Topics include:

• About this Guide

• Overview of the Quantum Control Software

• Features

About this Guide

This guide provides detailed information about the Quantum Elite Control Software and

Quantum Connect Control Software, including software installation and configuration.

This guide also describes how these applications control the Quantum Elite and Quantum

Connect videowall processors.

The features and functionality described in this guide are based on using version 1.8 of

the Quantum control software applications with Quantum Elite and Quantum Connect

firmware version 9.0 and later. For the latest details on firmware and software, visit

www.extron.com.

In this guide, the term “Quantum Control Software” refers to both the Quantum Elite Control

Software and Quantum Connect Control Software. The terms “Quantum” and “Quantum

processor” refer to both the Quantum Elite and Quantum Connect videowall processors.

Notes distinguish where features differ between the Quantum Elite and Connect Control

Software programs and between the Quantum Elite and Connect processors.

Overview of the Quantum Control Software

Quantum Elite Control Software and Quantum Connect Control Software are Microsoft

®

Windows

®

-based applications that are used to control the Quantum Elite and Quantum

Connect videowall processors. These products form part of the Extron Quantum series.

With the Quantum Control Software, the Quantum Elite and Connect can display multiple

image sources on a single target display or multiple target displays. External analog and

digital video sources (such as PAL or NTSC) and external analog and digital graphics

sources are supported. The Quantum processors also support the use of internal image files

(such as BMP, JPG, GIF, or PNG formats) or RGB computer graphics captured using the

QGE 100 Quantum Graphics Encoder.

The feature set supported by the Quantum Elite Control Software differs slightly from the

Quantum Connect Control Software. These differences are distinguished in this user guide.

NOTE: Quantum Elite Control Software is not compatible with the Quantum Connect

processor and vice versa.

Quantum Control Software • Introduction 1

Features

Features of the Quantum Control Software include:

• The user interface is organized into a series of tasks so that you can easily navigate

through them and set up the videowall.

• A virtual canvas provides an on-screen layout for the videowall where windows can be

added, sized, and positioned.

• Custom videowall configurations can be saved as window presets for future recall.

• The software lets you create a custom user interface so that the system operator can

easily recall the presets (scenes).

Scene control

Each source is displayed in a resizable window within the Quantum Control Software,

allowing multiple sources to be placed in any position on the display.

The Quantum Control Software stores different source layouts for the display as scenes,

which are presets that include the size, position, and contents of one or more windows.

Scenes can be recalled in any order using a customizable user interface or in a predefined

order at specific time intervals using the Auto Play function (see the Creating a Project

section beginning on page 41 and the Viewing a Project section beginning on page 61).

Scenes can also be recalled remotely via RS-232 (see Serial Commands beginning on

page 70).

Quantum Control Software • Introduction 2

Installation and

Operation

This section describes the software installation and communication setup for the Quantum

Control Software and describes the software operation. Topics include:

• Requirements

• Software Installation

• Configuring the Hardware

• Using the Quantum Control Software

Requirements

System Requirements

To ensure that the Quantum Control Software functions correctly and reliably, you must

install it on a computer that meets or exceeds the following criteria:

Minimum Recommended

Operating System Windows XP

®

Windows 7 or Windows 8

(32-bit or 64-bit)

Processor Speed 1 GHz 1 GHz or higher

Memory (RAM) 1 GB 1 GB or higher

Hard Disk Free Space 30 MB More than 30 MB

Graphics 1024x768, 65K colors

(16-bit)

1920 x 1080, 16.7M colors

(32-bit)

Network Card (Ethernet) 10Base-T 100BASE-T

Quantum Control Software • Installation and Operation 3

Network Requirements

The Quantum Elite and Quantum Connect use specific network ports for communication.

Ensure that these ports are accessible.

Quantum Elite

The Quantum Elite uses the following port numbers:

Port Number

Use

Control

1237 Quantum discovery (UDP)

7004 System configuration (TCP)

7005 Scene control (TCP)

7006 System events (TCP)

Media 1 and Media 2

5000 Multicast reception of QGE 100 data

stream (UDP)

37533 Discovery via Extron QGE 100 Computer

Screen Capture IP Encoder (UDP)

37532 Reception of QGE 100 data stream (TCP)

Quantum Connect

The Quantum Connect uses the following port numbers:

Port Number

User

Control

1238 Quantum discovery (UDP)

7007 System configuration (TCP)

7008 Scene control (TCP)

7006 System events (TCP)

Image Processing Hardware

The Quantum Control Software is used in conjunction with a Quantum Elite or Quantum

Connect videowall processor. Quantum Elite hardware consists of a 4U or 6U card frame

into which various input and output cards are installed. The Quantum Connect is available

only as a 4U frame. See the Quantum User Guide for more information about the Quantum

Elite and Quantum Connect, including connector pinouts and processing capability.

Except for defining an IP address, it is not necessary to perform any setup procedures on

the Quantum processor itself. System configuration is done through the control software.

Software Installation

To install the Quantum Control Software from the Extron Videowall Processing disc:

1. Insert the Extron Videowall Processing disc into the CD or DVD drive of your computer.

2. From the Windows desktop, open My Computer and select the appropriate disk drive.

3. Open the Quantum Connect or the Quantum Elite folder, depending on your device.

4. Open the appropriate software subfolder for your Quantum processor.

5. Run the Quantum Connect_Setupvn.nnn.exe file (for the Quantum Connect) or the

Quantum Elite_Setupvn.nnn.exe file (for the Quantum Elite).

6. Follow the remaining system prompts to complete the installation.

Quantum Control Software • Installation and Operation 4

Configuring the Hardware

Connecting to a Quantum Elite or Quantum Connect

The computer with the installed Quantum Control Software communicates with the

Quantum via Ethernet. This can either be a direct or indirect connection, as shown in

figure 1. Connection to a single videowall processor can use either method, but multiple

videowall processors must use the indirect method (for example, via a hub).

1 2345678910 11

IN ININ IN IN IN OUTOUT

MEDIA I

CONTROL

MEDIA II

12 13 14 15

WARNING

SEE USER GUIDE BEFORE

USING THIS EQUIPMENT

DO NOT REMOVE THIS PANEL

NO USER-SERVICEABLE

PARTS INSIDE

REFER ALL SERVICING TO

QUALIFIED SERVICE PERSONNEL

THIS EQUIPMENT MUST BE

GROUNDED/EARTHED

DO NOT OBSTRUCT

VENTILATION GRILLES

DO NOT EXPOSE THIS EQUIPMENT

TO RAIN OR MOISTURE

ATTENTION

OBSERVE PRECAUTIONS

FOR HANDLING

ELECTROSTATIC

SENSITIVE

DEVICES

Control Port

Ethernet

10BASE-T

Crossover Cable

Quantum Elite

Processor

Optional RS-232 Link

to Control Source Switchers

RS-232

Ethernet

10BASE-T

Straight-through

Cable

Other Quantum Elite Processors

or Network Sources/Devices

Quantum Elite

Processor

Optional RS-232 Link

to Control Source Switchers

RS-232

Direct Connection

Indirect Connection

Quantum Elite

Contr

ol Software

Quantum Elite

Contr

ol Software

12345678910 11

IN ININ IN IN IN OUTOUT

MEDIA I

CONTROL

MEDIA II

12 13 14 15

WARNING

SEE USER GUIDE BEFORE

USING THIS EQUIPMENT

DO NOT REMOVE THIS PANEL

NO USER-SERVICEABLE

PARTS INSIDE

REFER ALL SERVICING TO

QUALIFIED SERVICE PERSONNEL

THIS EQUIPMENT MUST BE

GROUNDED/EARTHED

DO NOT OBSTRUCT

VENTILATION GRILLES

DO NOT EXPOSE THIS EQUIPMENT

TO RAIN OR MOISTURE

ATTENTION

OBSERVE PRECAUTIONS

FOR HANDLING

ELECTROSTATIC

SENSITIVE

DEVICES

Control Port

HUB

Figure 1. Methods of Connecting the Quantum Elite Control Software Computer

to a Quantum Elite Processor

• A direct connection uses a single cable that is connected between the network port

of the computer and the Quantum Elite or Quantum Connect. You must use a crossover

cable; a straight-through cable does not work. The network port on the computer must

be capable of supporting a 10BASE-T connection as required by the Quantum.

• An indirect connection is made via a hub, switch, or local area network, using a

straight-through cable. A crossover cable does not work. The hub or switch connected

to the computer must be capable of supporting a 10BASE-T connection as required by

the Quantum.

Extron recommends using only CAT 5 shielded twisted pair cables. A 16-foot crossover

cable is supplied with the Quantum processor.

See the Quantum User Guide for further details on cable requirements and connector

pinouts.

Quantum Control Software • Installation and Operation 5

Setting the IP Address of the Computer

The network port on the computer must be configured to use the same communications

protocol as the Quantum, which is TCP/IP. The computer must also be allocated an IP

address on the same subnet as the Quantum (see IP Addressing on page 95).

To change the IP address for your computer, follow the instructions provided in your

Windows program help file.

NOTE: If the computer is already connected to (and configured for) an existing network,

consult the network administrator before making any changes. In addition, you need

to be logged on with administrative rights before you can change Windows network

settings.

Testing the Ethernet Link

To test the operation of the Ethernet link between the computer and the Quantum, you can

use the Ping utility as follows:

1. Enter a ping command from your desktop.

• Windows XP, 2000, and NT:

a. On the desktop, click Start > Run. The Run dialog box opens.

b. In the Run dialog box, type the following command:

ping nnn.nnn.nnn.nnn —t

where nnn.nnn.nnn.nnn is the IP address of the Quantum that you want to

test.

c. Click OK or press the <Enter> key.

• Windows 7:

a. On the desktop, click Start.

b. In the Search programs and files field at the bottom of the Start menu,

enter ping nnn.nnn.nnn.nnn —t and press <Enter>.

• Windows 8:

a. Search for CMD.

b. Double-click the cmd.exe application icon.

c. On the command line, type the following command:

ping nnn.nnn.nnn.nnn —t

where nnn.nnn.nnn.nnn is the IP address of the Quantum that you want to

test.

d. Click OK or press the <Enter> key. A command window opens.

One of the following response messages is displayed, indicating the state of the

communications link:

• Reply from nnn.nnn.nnn.nnn: bytes=nn times=nms TTL=nn

This is the desired response, which indicates that the device at the specified

address is communicating directly. The response time value may vary according to

network traffic.

Example: If you send a ping command to a Quantum with the address

208.132.180.48, you should get a message similar to the following:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

Quantum Control Software • Installation and Operation 6

• Request timed out

There has been no response from the specified address. Either the videowall

processor is not receiving data from the computer or is not sending data back.

Check that the Quantum Elite or Quantum Connect is powered up and set to the

same address to which you sent the ping command. Also, check that you are using

the correct type of connecting cables for your setup (straight-through or crossover)

and that they are not damaged or faulty.

• Reply from nnn.nnn.nnn.nnn: Destination host unreachable,

The IP address of the computer is not in the same class as that of your Quantum

(see IP Addressing on page 95). See your Windows program help file for

instructions for changing your computer IP address.

2. To close the ping utility, press <Ctrl + C> on your keyboard or click the X button in the

upper-right corner of the command window.

Using the Quantum Control Software

Starting and Exiting the Quantum Control Software

You can run the Quantum Control Software using any of the following methods:

• Double-click the Quantum Elite or Quantum Connect icon on the desktop.

• From the desktop, click Start > All Programs > Extron Electronics >

Quantum

Elite (or Quantum Connect).

• Double-click a project file (the file name has a CTP extension) in Windows Explorer.

If the Access Control feature has been enabled, a Login dialog box is displayed. Select an

appropriate logon level and enter a password (see the Access Control section beginning

on page 81).

The Quantum Control Software splash screen appears for a few seconds followed by the

main application window (see Main Application Window on the next page).

You can exit the Quantum Control Software using any of the following methods:

• From the File menu, select Exit.

• Click the button at the top right corner of the application window.

• Double-click the icon in the top left corner of the application window, or

single-click the same icon and select Close from the drop-down menu.

If you have not saved your project, a message is displayed asking whether you want to save

any changes. Click Yes or No to close the prompt.

Quantum Control Software • Installation and Operation 7

Main Application Window

The Quantum Control Software application window contains the following elements:

Figure 2. Elements of the Main Application Window

A

Title bar

D

Taskbar

B

Menu bar

E

Workspace

C

Toolbar

F

Status bar

A

Title bar — Shows the name of the currently loaded project.

B

Menu bar — Provides a selection of drop-down menus to access various functions in

the Quantum Control Software. Most of the menu functions can also be performed

by buttons on the toolbars. The available menus change according to which task is

currently selected in the taskbar.

C

Toolbars — The various toolbars within the Quantum Control Software allow quick

access to the most commonly used functions within the currently selected task. Most

of these functions can also be performed using the menu bar. To hide or show a toolbar

for the current task, open the View menu and select the desired toolbar. A check mark

beside the menu option denotes that the toolbar is open in the application. You can also

click and drag open toolbars to rearrange them in the application window.

Quantum Control Software • Installation and Operation 8

D

Taskbar — Each major task within the Quantum Control Software is represented by

an icon in the taskbar. To select a task, click the appropriate button. This displays the

workspace, menus, and toolbars associated with the selected task.

The standard set of tasks includes:

• Choose Display Processors • Scene Design

• Choose Layout • Scene Control

• Communications Setup • Remote Access Setup

• Set Up Sources • EDID Minder

Fewer tasks may be displayed depending on security settings.

E

Workspace — Each task in the taskbar has its own workspace. The workspace

contains the controls and functionality needed to complete the task.

F

Status bar — Shows information about the current status of the Quantum Control

Software. From the View menu, select Status Bar to hide or show the status bar.

Starting a New Project

When you run the Quantum Control Software for the first time after installation, a new

untitled project (presentation) is created with no system configuration settings (see figure 2

on the previous page).

Thereafter, you can start a new untitled project by either of the following methods:

• Retain the existing system configuration (for example, to create a new project for the

same system) by one of the following methods:

• Click the button on the main toolbar.

• From the File menu, select New.

• Press <Ctrl + N> on the keyboard.

• Create a completely new project with no system configuration (for example, to make a

new project for a different system). To create a new project:

3. Exit the Quantum Control Software (see Starting and Exiting the Quantum

Control Software on page 7 for instructions).

4. While holding down the <Shift> key on the keyboard, run the Quantum Control

Software (see Starting and Exiting the Quantum Control Software). When the

Quantum Control Software main screen opens, release the <Shift> key.

To give your untitled project a name, save it as the desired name (see Saving a Project on

page 10).

See the System Configuration section beginning on page 12 if you are creating a project

for a new system or need to make changes to the existing configuration.

See the Creating a Project section beginning on page 41 for information about placing

sources on the target display.

Quantum Control Software • Installation and Operation 9

Loading an Existing Project

1. Click the button on the main toolbar

- or -

From the File menu, select Open

- or -

Press <Ctrl + O> on the keyboard.

The Open dialog box appears.

2. Locate the file to be loaded and click Open.

Saving a Project

To save the current project:

1. Click the button on the main toolbar. You can also select Save from the File menu

or press <Ctrl + S> on the keyboard.

2. If the project has not been saved previously (untitled), the Save As dialog box opens,

allowing you to specify a name.

To save a copy of the open project:

1. From the File menu, select Save As. The Save As dialog box opens.

2. In the File Name field, enter a name for the project copy. A CTP extension is

automatically appended to the file name.

3. Click Save to save the file.

When creating a project, save your work regularly. You can also have the Quantum Control

Software automatically create backup files at regular intervals (see “Using Auto-Backup”).

Using Auto-backup

The Quantum Control Software can automatically back up your project at specific intervals.

In the event that any changes are lost before saving (such as due to a power outage), you

may be able to limit the amount of work you lost by restoring the last auto-backup file.

Setting the backup timer

1. From the Backup menu, select Setup Backup Timer. The Backup Setup Dialog box

opens.

Figure 3. Backup Setup Dialog Box

2. Ensure that the Disable Backup check box is cleared to enable auto-backup.

NOTE: If you do not want to use auto-backup, ensure that the Disable Backup

check box is selected.

Quantum Control Software • Installation and Operation 10

3. In the Hours and Minutes fields, enter the values to set the desired interval between

each backup.

4. In the Backup Folder field, enter the full path of the Windows folder where the backup

files are to be saved (by default, these are saved in the Quantum Elite or the Quantum

Connect folder)

- or -

In the Backup Folder field, click Browse to navigate to the folder where the files are to

be saved.

5. Click OK.

Restoring an auto-backup file

1. From the Backup menu, select Restore. If you made changes to the current file, you

are prompted to save the file first.

2. In the Save prompt, click Yes to save the current file. The Save As dialog box opens if it

is an untitled file.

- or -

Click No to exit the current file without saving.

The Open dialog box is displayed.

NOTE: Backup files are contained within folders according to the date they were

created. The files are named with the project title and the time they were created.

3. Double-click the folder for the desired date to open it.

4. Select the backup file that you want to restore and click Open.

Quantum Control Software • Installation and Operation 11

System

Conﬁguration

This section describes the four procedures or tasks associated with configuring the

Quantum Control Software to work correctly with a Quantum videowall processor. Topics

include:

• Choosing a Display Processor

• Layout Configuration

• Communications Setup

• Setting Up Sources

• Defining EDID

The tasks described in this section can be completed in any order but the order in which

they are listed above is recommended. Unless otherwise stated, all configuration settings

described in this section are saved in the project (CTP) file.

Choosing a Display Processor

Before the Quantum Control Software can control a Quantum, it must detect and be

connected to the processor via the Choose Display Processors task.

NOTE: Quantum Connect does not support the use of multiple processors.

Quantum Control Software • System Configuration 12

1. Click the Choose Display Processors button in the taskbar

(see figure 2,

D

, on page 8).

The Choose Display Processors workspace opens.

Figure 4. Choose Display Processors Workspace

2. Click the button on the main application window toolbar (see figure 4)

- or -

From the Detect menu, select Detect.

The Quantum Control Software polls for any Quantum processors accessible via its

Ethernet port. An information panel is displayed for each processor detected, as shown

in figure 4.

3. Select the Connect check box to the right of the IP address of the desired processor. If

you are using more than one Quantum, connect to each one in the same manner.

NOTE: If the check box does not stay selected, this indicates that the

Quantum Control Software is unable to establish or maintain a connection (for

instance, due to a faulty cable or the Quantum processor and PC not being on the

same IP subnet).

You can disconnect from a Quantum processor by clearing its Connect check box.

Quantum Control Software • System Configuration 13

Assigning a Name to a Quantum Processor

If you are using the Quantum Control Software to control more than one processor, you

can give a name to each Quantum that easily identifies its role within the system. This is

especially useful when you are assigning processors to the target display screens.

For example, if you are using two processors driving the left and right sides of the target

display array, you can name the two processors Left and Right, respectively.

To assign a name, enter a suitable name in the Name field for the processor.

Layout Configuration

Choosing a Display Layout

The target display can be a single screen or several screens interlocked to form a larger

display area. Therefore, you need to define the layout within the Quantum Control Software.

The selected layout appears as the virtual display in the Scene Design task (see the

Creating a Project section beginning on page 41). This allows you to place sources

exactly where you want them to appear on the actual display array.

Use the Choose Layout task to choose and configure the display layout.

To choose and configure a layout:

1. Click the Choose Layout button on the taskbar.

The Choose Layout workspace opens.

Figure 5. Choose Layout Workspace

Quantum Control Software • System Configuration 14

Page is loading ...

Extron Quantum Connect User manual

This manual is also suitable for

Extron Quantum Connect User manual

Related papers

Other documents