IMPORTANT INFORMATION EMV CHIP CARD PROCESSING
This device has the ability to process EMV chip cards. If you are
set up to accept chip cards, you will notice a few dierences.
1. Chip cards must be inserted into the device or pin pad if
attached (swiped transactions are not allowed).
2. The chip card must remain in the device until the transaction
is complete.
3. The transaction may require a customer to enter a PIN
(similar to a debit transaction).
4. Chip card transactions require the credit card to remain in
the the cardholder’s possession at all times.
For more information regarding EMV chip card acceptance and
processing, please visit: www.paymentstart.com/secure
INSTALLATION INSTRUCTIONS
Step 1: Open box
Step 2: Follow installation instructions on page 2
Step 3: Begin processing
CONTACT US:
www.paymentstart.com
for user guides and other DIY tips
1-866-451-4007
Activation & Training
8:30 AM – 9:00 PM ET, M-F
Look for Ingenico NA online
help videos on YouTube –
search for “Out of the box:
iCT200 Series.”
Ingenico iWL220 BT Series Installation Guide
Your
Payment Solutions
Team
DOCUMENT D’EXECUTION
INGENICO_CMJN.ai
INFORMATIONS GENERALESCOULEURS UTILISEES APPROBATION
Client: INGENICO
Date : 10 DEC 2013
Utilisation: Impression quadri.
Ne pas utiliser pour application
écran.
C 67/M 54
J 47/N 43
C 0/M 100
J 100/ N0
Inserng the paper roll
OR
Telephone
Power
Charging/Communicaon Base
Ethernet
Power Connecon
(Power should be connected aer communicaon connecon)
(Paper roll must feed as shown)
(Place the terminal on the base to charge)
Base Communicaon
(From the base, establish the communicaon connecon)
*8 hours of charging is recommended daily
Inserng the paper roll
OR
Telephone
Power
Charging/Communicaon Base
Ethernet
Power Connecon
(Power should be connected aer communicaon connecon)
(Paper roll must feed as shown)
(Place the terminal on the base to charge)
Base Communicaon
(From the base, establish the communicaon connecon)
*8 hours of charging is recommended daily
Inserng the paper roll
OR
Telephone
Power
Charging/Communicaon Base
Ethernet
Power Connecon
(Power should be connected aer communicaon connecon)
(Paper roll must feed as shown)
(Place the terminal on the base to charge)
Base Communicaon
(From the base, establish the communicaon connecon)
*8 hours of charging is recommended daily
Port
Inserng the paper roll
OR
Telephone (IN)
Router
Power
Hardware Installaon
Ethernet (ETH)
IN
EMV Chip Reader
(See back for more informaon)
Installing the Pin pad
(Pin pad must be installed before the power is connected)
Pin pad connecon
(USB HOST)
Pin pad
ETH
(Paper roll must feed as shown)
(Terminal & Magic Box should come pre-connected)
Magic Box
EMV Chip Reader
(See back for more informaon)
Port
Inserng the paper roll
OR
Telephone (IN)
Router
Power
Hardware Installaon
Ethernet (ETH)
IN
EMV Chip Reader
(See back for more informaon)
Installing the Pin pad
(Pin pad must be installed before the power is connected)
Pin pad connecon
(USB HOST)
Pin pad
ETH
(Paper roll must feed as shown)
(Terminal & Magic Box should come pre-connected)
Magic Box
EMV Chip Reader
(See back for more informaon)
BASE COMMUNICATION
(From the base, establish the communication connection)
POWER CONNECTION
(Power should be connected after communication connection)
CHARGING/COMMUNICATION BASE
(Place the terminal on the base to charge)
INSERTING THE PAPER ROLL
(Paper roll must feed as shown)
or
8-12 hours of charging is
recommended daily
-
1
-
2
Ingenico IWL220 GPRS Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ingenico PAYZONE iCT250 Operating instructions
-
Ingenico iCT220, iCT250 User manual
-
-
Ingenico iCT250E User manual
-
-
-
-
Ingenico DESK/3200 User manual
-
Ingenico Move 3500 User manual
-