2. Crystorama
  3. KEN-8305-PN
KEN-8305-PN

Crystorama KEN-8305-PN User manual

  • Hello! I've reviewed the assembly instructions for the Crystorama Light KEN-8305-PN. This document provides a step-by-step guide on how to assemble the light fixture, including installing the glass components and securing the fixture to the ceiling. I'm ready to assist with any questions you have regarding the installation or features mentioned in the instructions.
  • What type of bulb is recommended?
    Is this fixture suitable for damp locations?
    How do I change the bulb?
ASSEMBLYINSTRUCTIONMODEL#KEN-8305-PN
CRYST
RAMA
WARNING:
ElectricalDanger TurnPoweroff
WARNING: ThisproductcanexposeyoutoLead
whichisknowntothestateofCaliforniatocausecancer
and/orbirthdefectsorreproductiveharm.Formore
informationgotowww.P65Warnings.ca.gov
L I G H T I N GT H EW A YF O RS I X T YY E A R S
installedbyalicensedelectrician
inaccordancewiththeNational
Allelectricalcomponentsmustbe
ElectricCodeandtheappropriate
localelectricalcodes.
Howtoinstall
6.Installthebulb(notincluded)intothesocket.
This fixture is Damp rated
Youwillneed4-MediumBaseBulb
40WattsFrostedbulbRecommended
60WattsMax.
USELEDBULBSFOREXTENDEDUSE
1.Slidetheglassdiffuserontothebottomofmetal
frameandsecureitwithclips.
2.Slidetheglasspanelsinsidethemetalframeand
secureitwithclips.
3.Removescrew#2fromeachofthehooks.Place
onehookontothebottomofthebracketonthe
metalframebyinsertingscrew#1intothe1st
holeonthebracket.
Whileholdingthehookinplace,placethetop
metalringoverthetopofthebracketbyaligning
theholeonitwiththe2ndholeonthebracket
andhook.Secureitwithscrew#2.Repeatthis
forotherhooks.
OUTLETBOXSCREWS
MOUNTINGPLATE
MOUNTINGSCREWS
CEILINGPAN
METALTAB
BALLNUT
SOCKET
SCREW#2
TOPMETALRING
GLASSPANEL
(4PCS)
GLASSDIFFUSER
BRACKET
METALFRAME
CLIP
CLIP
HOOK
4.Installthemountingscrewsintothematching
holesinthemountingplate.Securethemounting
platetotheoutletboxwiththeoutletboxscrews.
5.Raiseceilingpanallowingthemountingscrews
toprotrudethroughtheholesintheceilingpan,
andsecurewiththeballnut.
7.Placethemetalframeovertheceilingpanby
insertingthehooksintotheholesofthemetal
tabontheceilingpan.
20-5/8’’
3-1/8’’
3-7/8’’
15-1/4’’
GLASSPANEL
GLASSDIFFUSER
5-1/4’’
22-1/2’’
15’’
1sthole 2ndhole
2ndhole
SCREW#1 Howtochangethebulb:
Raisethemetalframeupovertheceilingpanand
turnitsidewaytotakeitdown.Installthenewbulb
andputthemetalframeback.
Crystorama.com
CRYST
RAMA
L I G H T I N GT H EW A YF O RS I X T YY E A R S
PartNumber
PartNumbers
A.(1)-Mountinghardware
C.(1)-Ceilingpan
D.(4)-Socket
E.(4)-Screw
ASSEMBLYINSTRUCTIONMODEL#KEN-8305-PN
C
BA
D
E
F
B.(2)-Ballnut#XRF8305PNBANUT
H
I
J
F.(1)-Topmetalring
G.(4)-GlasspanelL15-1/4’’xW3-7/8’’xH3-1/8’’ #XRF8304GLA15.25IN
H.(1)-GlassdiffuserW20-5/8’’ #XRF8304DIFF20.625IN
I.(4)-Hook
G
J.(1)-Metalframe
Crystorama.com
/