Turn off the power at fuse or circuit box.
1. Attach the mounting strap
unit (A) to the outlet box by
using two mounting screws (B).
Note: The depth of threaded
pipe on the mounting strap
unit may need to be adjusted
to properly fit the fixture.
Page 1 of 2
Hardware Package (
included
):
Installation Steps
Mounting Strap Unit (A) Mounting Screw (B) Wire Connector (C) Finial (D) Quick Link (E) Chain (F)
W
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
H0270
2. Secure the two rods onto the
fixture by using the threaded
pipes. Determine length of
chain (F) needed to achieve
desired fixture height. (To
remove excess chain section,
use pliers to bend link open.)
Weave the fixture wires
through the chain (F) and
canopy.
Connect the two chains (F)
to the canopy and fixture
loops with four quick links (E).
4. Attach the canopy to the
mounting strap unit (A) by
aligning and inserting the
threaded pipe from the
mounting strap unit (A) into
the center hole on the
canopy, then secure the
canopy with the finial (D).
3. Pull out the source wires from
the outlet box. Make wire
connections using wire
connectors (C) as follows:
---Connect the smooth-coated
wire (marked) from the fixture
to the black wire (hot) from
the power source.
---Connect the ribbed-coated
wire (unmarked) from the
fixture to the white wire
(neutral) from the power source.
---Attach the fixture ground wire (bare wire) to the mounting
strap unit (A) with the green ground screw. Then, depending
on local code, connect it to the house ground wire with a
wire connector (C).
Carefully put all of the wires back into the outlet box.
1
Outlet Box
Mounting Strap Unit (A)
Mounting Screw (B)
2
A
Fixture Loop
Fixture
Canopy
Quick Link (E)
Quick Link (E)
Chain (F)
Rod
3
Outlet Box
Green Ground
Screw
Wire Connector (C)
Mounting Strap Unit (A)
4
Canopy
Finial (D)
Mounting Strap Unit (A)
220602
Spare Parts List:
The following parts are available for re-order if damaged or missing.
Assembly Kit
6522MM (1 SET)
Turn on the power at fuse or circuit box.
Page 2 of 2
ASSEMBLY INSTRUCTIONS (continued)
5. Install 3 x 60W medium base bulbs.
See relamping label at socket area or packaging for maximum wattage allowed.
5
Max. 60W Medium Base Bulb
Mounting Strap Unit (A) Mounting Screw (B) Wire Connector (C) Finial (D) Quick Link (E) Chain (F)
220602
A: 24"
B: 40-1/4"
C: 11-1/2"
A
BC
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Kichler Lighting 43745OZ User manual
-
Kichler Lighting 42497NI User manual
-
Kichler Lighting 42474PN User manual
-
Kichler Lighting 43754AUB User manual
-
Kichler Lighting 43755AUB User manual
-
Kichler Lighting 44009MIZ User manual
-
Kichler Lighting 42140BK User manual
-
Kichler Lighting 43992AP User manual
-
Kichler Lighting 43993OZ User manual
-
Kichler 43059CLP Operating instructions
