Kuzco Lighting PD88148 User manual

Brand: Kuzco Lighting

Model: PD88148

Type: User manual

Kuzco Lighting PD88148 is a ceiling LED pendant light fixture designed for indoor use. It features a pre-wired LED module, eliminating the need for bulbs. The fixture is dimmable using an ELV (Electronic Low Voltage) or TRIAC dimmer, allowing you to adjust the brightness to your preference. Installation requires a qualified licensed electrician and involves attaching the mounting plate to the electrical junction box, securing the fixture to the mounting plate, and making proper electrical connections. The fixture comes with adjustable wire length, enabling you to customize the hanging height.

19054 28th Avenue Surrey, BC Canada V3Z 6M3

T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196

W: kuzcolighting.com

INSTALLATION SHEET

PD88148

Ceiling LED Pendant

1a.

1b.

1c.

1e.

2g.

2b.

2a.

START FROM HERE

• Make sure POWER is COMPLETELY OFF at the fuse box

• Have your fixture installed by a qualified licensed electrician

• Prepare everything in a clear area

• Wear gloves at all time during this installation

• Read instructions carefully before you start assembly

• Keep this installation sheet for future reference

Technical Support: 1-855-855-8926

Page 1 of 2

Please Note:

• This Kuzco LED fixture comes with pre-wired LED module(s)

• Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary

contact with the module could cause permanent damage

• Use ELV (Electronic Low Voltage) or TRIAC type of dimmer for dimming application

• 120V input

1f.

1g.

1. Remove fixture from its original package

2. Separate mounting plate (1c) from canopy (2a) by

removing canopy screws (2b)

3. Attach mounting plate (1c) to electrical junction box (1a)

using junction box screws provided (1e) in hardware

package

4. Secure mounting plate (1c) to mounting surface with

anchors (1f) and screws (1g)

5. To change fixture height, push and hold wire gripper

(2g), slide wire to desired length and then release wire

gripper (2g) to secure

6. Make proper electrical connections (black to hot “L”,

white to neutral “N”, ground to “GND”) with wire nuts

(1b) provided in hardware package

7. Attach canopy (2a) to mounting plate (1c) with canopy

screws (2b)

8. Fine tone wire length if necessary, by push and hold

wire gripper (2g) and then adjust wire to desired length

20220322

19054 28th Avenue Surrey, BC Canada V3Z 6M3

FOR ALTERNATIVE SIDE CANOPY INSTALL

T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196

W: kuzcolighting.com

INSTALLATION SHEET

PD88148

Ceiling LED Pendant

1a.

1b.

1c.

3c.

3b.

3d.

3e.

3a.

2g.

7a.

2a.

1e.

4a.

4b.

2b.

Note: Ideal distance of wire

grippers from canopy is

46-7/16” and 44-3/16”

START FROM HERE

• Make sure POWER is COMPLETELY OFF at the fuse box

• Have your fixture installed by a qualified licensed electrician

• Prepare everything in a clear area

• Wear gloves at all time during this installation

• Read instructions carefully before you start assembly

• Keep this installation sheet for future reference

Technical Support: 1-855-855-8926

2g.

Page 2 of 2

Driver

Illustration 3

Low Voltage

Driver

44-3/16”

46-7/16”

Please Note:

• This Kuzco LED fixture comes with pre-wired LED module(s)

• Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary

contact with the module could cause permanent damage

• Use ELV (Electronic Low Voltage) or TRIAC type of dimmer for dimming application

• 120V input

Illustration 1 Illustration 2

6c.

Ground Wire

7a.

6a.

2g.

6b.

2a.

5a. Ground

Wire

2a.

1. Disconnect output wires on driver (4a)

2. Separate wire gripper (2g) from canopy (2a) by removing

nut and tooth washer (6a). Separate plug (6b) from canopy

(2a) by removing nut, tooth washer and flat washer (6c)

(See Illustration 1)

3. Feed fixture wires through centre hole on canopy plate

(7a), canopy (2a), tooth washer and nut (5a). Attach

canopy plate (7a) to canopy (2a), followed by wire gripper

(2g) and secure with tooth washer and nut (5a) (See

Illustration 2)

4. Make proper electrical connections between LED and DC

driver, LED- Negative, LED+ Positive using wago connector

(4b) provided (See Illustration 3 and refer to diagram on

driver)

5. Make proper electrical connections (black to hot “L”,

white to neutral “N”, ground to “GND”) with wire nuts

(1b) provided in hardware package

6. Attach canopy (2a) to mounting plate (1c) with canopy

screws (2b). Position desired amount of wire by

pushing gripper (2g) on canopy

7. Pull wire through aircraft barrel (3b) and stopper (3d).

Secure aircraft barrel (3b) to mounting surface with anchor

(3c) and screw (3a). Adjust wire to desired length and

secure with set screw (3e). Insert wire gripper (2g) into

aircraft barrel (3b) to close

8. Fine tone wire length if necessary, by push and hold

wire gripper (2g) and then adjust wire to desired length

20220322

Kuzco Lighting PD88148 User manual

Kuzco Lighting PD88148 User manual

Kuzco Lighting PD88148 User manual

Related papers

Other documents