Architectural Area Lighting KicK Bollard series Installation guide

Brand
Architectural Area Lighting
Model
KicK Bollard series
Type
Installation guide

This manual is also suitable for

KicK Bollard Installation Instruction
Fixture: KB6 - KicK Bollard
A R C H I T E C T U R A L A R E A L I G H T I N G
93069784 REV. B
PAGE 1/8
www.aal.net
16555 East Gale Avenue
City of Industry, CA 91745
626.968.5666
2 1 93069764 TMPLT-MTG-KB6
1 4 A90007 BOLT-ANCH 1/2 x10 x2
ITEM # QTY PART # DESCRIPTION
Tools required:
1. 9/16" Socket & Rachet Arm
2. Wire connections to incoming power (others)
3. 3/16" Allen Wrench
2
1
WAR
NING: Fixtures must be grounded in accordance with local codes or the National Electrical
Code. Failure to do so may result in serious personal injury.
MAINTENANCE: A regularly scheduled maintenance program should be established to retain optimum light
output and reduce heat retention.
CAUTION: All wiring must be done by a qualified electrician. KEEP THIS SHEET FOR FUTURE REFERENCE.
!
KicK Bollard Installation Instruction
Fixture: KB6 - KicK Bollard
A R C H I T E C T U R A L A R E A L I G H T I N G
93069784 REV. B
PAGE 2/8
www.aal.net
16555 East Gale Avenue
City of Industry, CA 91745
626.968.5666
1.
REMOVE SET SCREWS
1. Remove 4 x 3/8-16 set screws.
2. Remove the fixture housing by pulling
the housing upward.
3/8-16 SET SCREWS
FIXTURE HOUSING
FIG. 1-1
FIG. 1-2
KicK Bollard Installation Instruction
Fixture: KB6 - KicK Bollard
A R C H I T E C T U R A L A R E A L I G H T I N G
93069784 REV. B
PAGE 3/8
www.aal.net
16555 East Gale Avenue
City of Industry, CA 91745
626.968.5666
2.
REMOVING BOLLARD BASE
A
DETAIL A
1. Remove 4 x 3/8-16 screws and washers
f
rom the bollard base, and remove the
fixture assembly.
3/8-16 SCREWS
3/8-16 WASHERS
FIXTURE ASSEMBLY
BOLLARD BASE
FIG. 2-1
KicK Bollard Installation Instruction
Fixture: KB6 - KicK Bollard
A R C H I T E C T U R A L A R E A L I G H T I N G
93069784 REV. B
PAGE 4/8
www.aal.net
16555 East Gale Avenue
City of Industry, CA 91745
626.968.5666
3.
INSTALLING BOLLARD BASE
1. Placed the anchor bolt template on the
desired location, and install the anchor
bolt according to the determined location.
2. Install the bollard base on the anchor bolts
and tighten the washers and nuts to keep
the bollard base level to the ground.
ANCHOR BOLT TEMPLATE
BOLLARD BASE
ANCHOR BOLT WASHER
ANCHOR BOLT NUT
ANCHOR BOLT
FIG. 3-1
KicK Bollard Installation Instruction
Fixture: KB6 - KicK Bollard
A R C H I T E C T U R A L A R E A L I G H T I N G
93069784 REV. B
PAGE 5/8
www.aal.net
16555 East Gale Avenue
City of Industry, CA 91745
626.968.5666
4.
WIRING CONNECTION
1. Make the wiring connection, see wiring
diagram on page 6 for detail information.
FIG. 2-1FIG. 4-1
KicK Bollard Installation Instruction
Fixture: KB6 - KicK Bollard
A R C H I T E C T U R A L A R E A L I G H T I N G
93069784 REV. B
PAGE 6/8
www.aal.net
16555 East Gale Avenue
City of Industry, CA 91745
626.968.5666
( - ) GRAY
( + ) VOILET
( - ) GRAY
( + ) VIOLET
BLACK
GREEN
WHITE
TO INCOMING
POWER
GROUND TO
FIXTURE HOUSING
Driver Assembly
TO DIMMING
(OPTIONAL)
( - ) BLUE
( + ) RED
LED Array
( - ) BLUE
( + ) RED
TO LEDs
BLUE
BLUE
BLUE
BLUE
TO NTC
PROBE
BLACK
GREEN
WHITE
KicK Bollard Wiring Diagram
KicK Bollard Installation Instruction
Fixture: KB6 - KicK Bollard
A R C H I T E C T U R A L A R E A L I G H T I N G
93069784 REV. B
PAGE 7/8
www.aal.net
16555 East Gale Avenue
City of Industry, CA 91745
626.968.5666
5.
INSTALLING FIXTURE ASSEMBLY
DETAIL A
1. Determine the street side desired, and
i
nstall the fixture assembly to the
bollard base.
2. Install 4 x 3/8-16 screws and washers
to the bollard base to secure the fixture
assembly to the bollard base.
3/8-16 SCREWS
3/8-16 WASHERS
FIXTURE ASSEMBLY
A
BOLLARD BASE
STREET SIDE
FIG. 5-1
F
IG. 5-2
KicK Bollard Installation Instruction
Fixture: KB6 - KicK Bollard
A R C H I T E C T U R A L A R E A L I G H T I N G
93069784 REV. B
PAGE 8/8
www.aal.net
16555 East Gale Avenue
City of Industry, CA 91745
626.968.5666
6.
INSTALLING THE FIXTURE HOUSING
1. Insert the fixture housing to the bollard
fixture assembly.
2. Insert 4 x 3/8-16 set screws, and tighten
the set screws on all 4 sides.
3. Installation is complete.
3/8-16 SET SCREWS
FIXTURE HOUSING
FIG. 6-1
F
IG. 6-2 FIG. 6-3
KicK Bollard Installation Instruction
Fixture: KB6 - KicK Bollard
A R C H I T E C T U R A L A R E A L I G H T I N G
93069784 REV. B
PAGE 1/8
www.aal.net
16555 East Gale Avenue
City of Industry, CA 91745
626.968.5666
BOLT PATTERN TEMPLATE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Architectural Area Lighting KicK Bollard series Installation guide

Brand
Architectural Area Lighting
Model
KicK Bollard series
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents