Sonifex RM-4C8 Reference Monitor Owner's manual

Reference Monitors

User Handbook

RM-2S4 Reference Monitor, 2 LED meters & 4 stereo

channel inputs

RM-2S10 Reference Monitor, 2 LED meters & 10 stereo

channel inputs

RM-4C8 Reference Monitor, 4 LED meters, 8 channel inputs

& dual selectors

RM-HD1 HD-SDI expansion card

RM-HDE1 HD-SDI & Dolby* E Decoder expansion card

b

Reference Monitors User Handbook

This handbook is for use with the following product:

RM-2S4 Reference Monitor, 2 LED meters & 4 stereo channel inputs

RM-2S10 Reference Monitor, 2 LED meters & 10 stereo channel inputs

RM-4C8 Reference Monitor, 4 LED meters, 8 channel inputs & dual selectors

RM-HD1 HD-SDI expansion card

RM-HDE1 HD-SDI & Dolby* E Decoder expansion card

©Sonifex Ltd, 2008

Revision 1.04, August 2008

Sonifex Ltd, 61, Station Road, Irthlingborough,

Northants, NN9 5QE, England.

Tel: +44 (0)1933 650 700

Fax: +44 (0)1933 650 726

Email: [email protected].uk

Website: http://www.sonifex.co.uk

Information in this document is subject to change without notice and does not represent a commitment on the part of

the vendor. Sonifex Ltd shall not be liable for any loss or damage whatsoever arising from the use of information or any

error contained in this manual.

No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical,

including photocopying, recording, information storage and retrieval systems, for any purpose other than the purchaser’s

personal use, without the express written permission of Sonifex Ltd. Unless otherwise noted, all names of companies,

products and persons contained herein are part of a completely ctitious adaptation and are designed solely to

document the use of Sonifex product.

* Dolby and the double-D symbol are registered trademarks of Dolby Laboratories

REFERENCE MONITOR USER HANDBOOK

REFERENCE MONITORS

Reference Monitors User Handbook

c

CONTENTS

Warranty i

Warranty and Liability i

Unpacking the Reference Monitor iii

Returning the Warranty Card iii

Safety Information iv

Safety of Mains Operated Equipment iv

Voltage Setting Checks iv

Fuse Rating iv

Power Cable and Connection iv

Ordering the Correct Mains Lead v

Installation Information v

Atmosphere v

Electromagnetic Radiation v

WEEE & RoHS Directives - Sonifex Statement vi

Reference Monitors Introduction 1

RM-2S4 Reference Monitor, 2 LED meters & 4 stereo channel inputs 3

RM-2S10 Reference Monitor, 2 LED meters & 10 stereo channel inputs 3

Introduction 3

System Block Diagram 4

Front Panel Indicators & Controls 5

Audio Modiers 12

Rear Panel Connections & Operation 14

Technical Specication RM-2S4 & RM-2S10 21

RM-4C8 Reference Monitor, 4 LED meters, 8 channel inputs & dual selectors 26

Introduction 26

System Block Diagram 27

Front Panel Indicators & Controls 28

Audio Modiers 34

Rear Panel Connections & Operation 36

Technical Specication RM-4C8 41

RM-HD1 Reference Monitor HD-SDI Expansion Card & 46

RM-HDE1 Reference Monitor HD-SDI & Dolby E Decoder Expansion Card 46

System Block Diagram 47

Technical Specication RM-HD1 & RM-HDE1 48

Serial Interface Commands & Responses Protocol 49

Serial Data Format 49

Remote Control Commands 49

Reference Monitor SCi Remote Control Software 54

Download the Latest SCi Software 54

Connecting Using USB Port 54

Connecting using the RS232 Serial Port 54

Using SCi For The First Time 54

SCi For Reference Monitors 56

d

Reference Monitors User Handbook

FIGURES

Figures

Fig A: Packing List iii

Fig B: Power Connections iv

Fig C: Mains Lead Table v

Fig 1-1: RM-2S4 Reference Monitor Front Panel 3

Fig 1-2: RM-2S10 Reference Monitor Front Panel 3

Fig 1-3: Reference Monitor Block Diagram 4

Fig 1-4: RM-2S4 Front Panel Controls 5

Fig 1-5: RM-2S10 Front Panel Controls 5

Fig 1-6: RM-2S4 Source Selector 5

Fig 1-7: RM-2S10 Source Selector 5

Fig 1-8: RM-2S4 & RM-2S10 Meters 7

Fig 1-9: RM-2S4 & RM-2S10 DIPSwitch Settings 8

Fig 1-10: Meter Labelling Options 9

Fig 1-11: Brightness Control 9

Fig 1-13: Balance Control 10

Fig 1-12: Phase Meter Display 10

Fig 1-14: Status LEDs 11

Fig 1-15: RM-2S4 & RM-2S10 Modier Switches 12

Fig 1-16: Reference Monitor RM-2S4 Rear 14

Fig 1-17: Reference Monitor RM-2S10 Rear 14

Fig 1-18: RM-2S4 & RM-2S10 DIPswitch Settings 15

Fig 2-1: RM-4C8 Reference Monitor Front Panel 26

Fig 2-2: Reference Monitor Block Diagram 27

Fig 2-3: RM-4C8 Front Panel Controls 28

Fig 2-4: RM-4C8 Rotary Source Selectors 28

Fig 2-5: RM-4C8 Meters 29

Fig 2-6: RM-4C8 DIPSwitch Settings 30

Fig 2-7: Meter Labelling Options 31

Fig 2-8: Brightness Control 32

Fig 2-9: Phase Meter Display 32

Fig 2-10: Balance Control 32

Fig 2-11: Status LEDs 33

Fig 2-12: RM-4C8 Modier Switches 34

Fig 2-13: RM-4C8 Rear 36

Fig 3-1: RM-HD1 Expansion Card 46

Fig 3-2: RM-HDE1 Expansion Card 46

Fig 3-3: RM-HD(E)1 Block Diagram 47

Fig 5-1: SCi Launcher 54

Fig 5-2: SCi Device Discovery Panel 55

Fig 5-3: SCi Device Information Panel 55

Fig 5-4: SCi Launcher Loaded 55

Fig 5-5: SCi Main Screen 56

Reference Monitors User Handbook

i

Warranty

Warranty and Liability

Important: the purchaser is advised to read this clause

(a) The Company agrees to repair or (at its discretion) replace Goods which are found to

be defective (fair wear and tear excepted) and which are returned to the Company

within 12 months of the date of despatch provided that each of the following

are satised:

(i) notication of any defect is given to the Company immediately upon its

becoming apparent to the Purchaser;

(ii) the Goods have only been operated under normal operating conditions and

have only been subject to normal use (and in particular the Goods must have

been correctly connected and must not have been subject to high voltage or

to ionising radiation and must not have been used contrary to the Company’s

technical recommendations);

(iii) the Goods are returned to the Company’s premises at the Purchaser’s expense;

(iv) any Goods or parts of Goods replaced shall become the property of

the Company;

(v) no work whatsoever (other than normal and proper maintenance) has been

carried out to the Goods or any part of the Goods without the Company’s prior

written consent;

(vi) the defect has not arisen from a design made, furnished or specied by

the Purchaser;

(vii) the Goods have been assembled or incorporated into other goods only in

accordance with any instructions issued by the Company;

(viii) the defect has not arisen from a design modied by the Purchaser;

(ix) the defect has not arisen from an item manufactured by a person other than

the Company.

In respect of any item manufactured by a person other than the Company, the Purchaser

shall only be entitled to the benet of any warranty or guarantee provided by such

manufacturer to the Company.

(b) In respect of computer software supplied by the Company the Company does not

warrant that the use of the software will be uninterrupted or error free.

WARRANTY

ii

Reference Monitors User Handbook

(c) The Company accepts liability:

(i) for death or personal injury to the extent that it results from the negligence of

the Company, its employees (whilst in the course of their employment) or its

agents (in the course of the agency);

(ii) for any breach by the Company of any statutory undertaking as to title, quiet

possession and freedom from encumbrance.

(d) Subject to conditions (a) and (c) from the time of despatch of the Goods from the

Company’s premises the Purchaser shall be responsible for any defect in the Goods

or loss, damage, nuisance or interference whatsoever consequential economic or

otherwise or wastage of material resulting from or caused by or to the Goods. In

particular the Company shall not be liable for any loss of prots or other economic

losses. The Company accordingly excludes all liability for the same.

(e) At the request and expense of the Purchaser the Company will test the Goods to

ascertain performance levels and provide a report of the results of that test. The

report will be accurate at the time of the test, to the best of the belief and knowledge

of the Company, and the Company accepts no liability in respect of its accuracy

beyond that set out in Condition (a).

(f) Subject to Condition (e) no representation, condition, warranty or other term,

express or implied (by statute or otherwise) is given by the Company that the Goods

are of any particular quality or standard or will enable the Purchaser to attain any

particular performance or result, or will be suitable for any particular purpose or use

under specic conditions or will provide any particular capacity, notwithstanding

that the requirement for such performance, result or capacity or that such particular

purpose or conditions may have been known (or ought to have been known) to the

Company, its employees or agents.

(g) (i) To the extent that the Company is held legally liable to the Purchaser for any

single breach of contract, tort, representation or other act or default, the

Company’s liability for the same shall not exceed the Price of the Goods.

(ii) The restriction of liability in Condition (g)(i) shall not apply to any liability

accepted by the Seller in Condition (c).

(h) Where the Goods are sold under a consumer transaction (as dened by the

Consumer Transactions (Restrictions on Statements) Order 1976) the statutory

rights of the Purchaser are not aected by these Conditions of Sale.

WARRANTY

Reference Monitors User Handbook

iii

Unpacking the Reference Monitor

The Reference Monitor is shipped with the following equipment. Please check your

packaging to ensure that you have all of the items below. If anything is missing, please

contact the supplier of your equipment immediately.

Item Quantity Reference Monitor

Reference Monitor 1

IEC mains lead tted with moulded mains plug 1

Handbook and warranty card 1

Overlay sheet for metering 1

USB cable 1

Fig A: Packing List

Each Reference Monitor is shipped in protective packaging and should be inspected for

damage before use. Where an item is found to have transit damage, notify the carrier

immediately with all the relevant details of the shipment. Packing materials should be kept

for inspection and also for if the product needs to be returned.

Returning the Warranty Card

In order to register the date of purchase so that we can keep you informed of any design

improvements or modications, it is important to complete the warranty registration

document that is enclosed and return it to Sonifex Ltd in the UK.

For your own records you should write down the serial number (which can be found on the

rear of the Reference Monitor.

Serial Number ………………………………………

WARRANTY

iv

Reference Monitors User Handbook

Safety Information

Safety of Mains Operated Equipment

This equipment has been designed to meet the safety regulations currently

advised in the country of purchase and it conforms to the safety regulations

specied by use of the CE Mark.

Warning : There are no user serviceable parts inside the equipment. If you should ever

need to look inside the unit, always disconnect the mains supply before removing the

equipment covers.

Voltage Setting Checks

Ensure that the machine operating voltage is correct for your mains power supply by

checking the box in which your Reference Monitor was supplied. The voltage is shown

on the box label. The available voltage settings are 115V, or 230V. Please note that all

Reference Monitores are either switchable between 115V and 230V, or have a universal

power supply.

Fuse Rating

The Reference Monitor is supplied with a single fuse in the live conducting path of the

mains power input. For reasons of safety it is important that the correct rating and type of

fuse is used. Incorrectly rated fuses could present a possible re hazard, under equipment

fault conditions. The fuse rating for the Reference Monitor is:

230 or 115 V operation - 2A 5 x 20mm SB

The active fuse is tted on the outside rear panel of the unit.

Power Cable and Connection

An IEC power connector is supplied with the Reference Monitor which has a moulded plug

attached – this is a legal requirement. If no moulded plug has been supplied with your

Reference Monitor, please contact your supplier, because an IEC connector is always

supplied from the Sonifex factory.

If for any reason, you need to use the Reference Monitor with a dierent power cable, you

should use the following wiring guidelines.

Wire Colour Connection

Green, or green and yellow Earth (E)

Blue, or black Neutral (N)

Brown, or red Live (L)

Fig B: Power Connections

Connect the equipment in accordance with the connection details and before applying

power to the unit, check that the machine has the correct operating voltage for your mains

power supply.

Important Note : The terminal marked on the rear panel must be earthed.

SAFETY INFORMATION

Reference Monitors User Handbook

v

Ordering the Correct Mains Lead

When ordering a Reference Monitor from Sonifex, it is helpful if you can specify your

required operating voltage and mains lead. After the product code add:

UK, for 230V, UK 3 pin to IEC lead

EC, for 230V, European Schuko 2 pin to IEC lead

US, for 115V, 3 pin to IEC lead

AU for 230V, Australasian 3 pin to IEC lead

Fig C: Mains Lead Table

E.g. order RM-2S4 UK for a UK IEC lead to be supplied.

Installation Information

Atmosphere

The units should be installed in an area that is not subject to excessive temperature

variation (<0°C, >50°C), moisture, dust or vibration.

Electromagnetic Radiation

The cover is connected to earth by means of the xing screws. It is essential to maintain

this earth ground connection to ensure a safe operating environment and provide

electromagnetic shielding.

SAFETY INFORMATION

vi

Reference Monitors User Handbook

WEEE & RoHS Directives - Sonifex Statement

The Waste Electrical and Electronic Equipment (WEEE) Directive was agreed on

13 February 2003, along with the related Directive 2002/95/EC on Restrictions

of the use of certain Hazardous Substances in electrical and electronic

equipment (RoHS).

The Waste Electrical and Electronic Equipment Directive (WEEE) aims to minimise the

impacts of electrical and electronic equipment on the environment during their life times

and when they become waste. It applies to a huge spectrum of products. It encourages

and sets criteria for the collection, treatment, recycling and recovery of waste electrical and

electronic equipment. All products manufactured by Sonifex Ltd have the WEEE directive

label placed on the case. It gives a contact for individuals who are unsure about the correct

procedure when the product has reached its “end of use”.

Sonifex Ltd will be happy to give you information about local organisations that can

reprocess the products, or alternatively all products that have reached “end of use” can be

returned to Sonifex and will be reprocessed correctly free of charge.

Sonifex Ltd has phased out the use of certain hazardous substances identied in the

European Union’s Restriction of Hazardous Substances (RoHS) directive. The RoHS

directive limits the use of certain hazardous substances currently used in EEE manufacture,

including lead, mercury, cadmium, hexavalent chromium, and halide-containing

compounds PBB (polybrominated biphenyl) and PBDE (polybrominated diphenyl ether).

Elimination of these substances will result in more environmentally friendly recycling

of electronic equipment. For the products which Sonifex manufacture, the main area

where products were aected was in the use of lead for manufacturing and assembling

electronics circuit boards.

Sonifex Ltd practices lead-free (LF) manufacturing processes. LF solder is used on the

surface-mount PCB manufacturing processes and for hand soldering. The printed circuit

boards (PCBs) used are either gold plated, or immersion tin plated, both of which use no

lead. Historically the PCBs were hot air solder levelled (HASL) PCBs which used tin/lead

based solder.

The manufacturing processes include the assembly of purchased components from

various sources. Product is oered as RoHS compliant, or LF, only after sucient evidence

is received from the component manufacturers that their components are RoHS compliant.

Sonifex Ltd relies solely on the distributor, or manufacturer, of the components for

identication of RoHS compliance. Thus whilst every eort is made to ensure compliance,

Sonifex Ltd makes no warranty, or certication, or declaration of compliance concerning

said components.

Sonifex Ltd denes “Lead Free” as pertaining to any product, which has been manufactured

by Sonifex Ltd using components which have been declared by the manufacturers as

“Lead Free”. All statements by Sonifex Ltd of RoHS compliance are based on component

manufacturer documentation.

WEEE & ROHS DIRECTIVE

Reference Monitors User Handbook

1

REFERENCE MONITORS

Reference Monitors Introduction

The Reference Monitor Range is a series of rack-mount audio monitors,

combining the latest DSP technology with outstanding audio enclosure design

to produce monitors of the highest standards with exceptional sound quality,

a comprehensive feature set and good looks in the rack.

Uniquely an embedded 5 band parametric EQ allows you to configure the

monitor for your environment or to suit your listening tastes.

Detail In The Design

In the design of the product, every care has been taken to ensure the best and most

accurate reproduction of the audio sources.

In a 1U rack, the propogation of high power sound waves in such a small enclosure could

have a tendency to produce rattles or move components, but the Reference Monitors have

been designed to ensure that their audio performance is not compromised.

Anti-Vibration

A welded and sealed stainless-steel case with milled aluminium fascia provides exceptional

rigidity and has been used to ensure that there are no extraneous metallic rattles. The lid

is sealed with extensive thin foam cut-outs to provide damping to the lid and multi-point

screw xings are used to ensure lid rigidity.

The XLR and USB port connectors on the rear panel are sealed with foam, and silicon

sealant is used on components which could move, or vibrate, under high SPL conditions.

Accurate Sound System

The speaker system comprises a three-way arrangement with two mid/high frequency

speakers providing excellent stereo imaging and a separately driven, forward facing, dual

magnet, mono bass driver.

Custom-moulded, proled, HF enclosures are used to minimise standing waves and

eliminate response peaks, and acoustic damping in the HF enclosures is used to reduce

colouration, eectively creating a separate, sealed, innite-bae enclosure for each driver.

Reference Monitors User Handbook

2

REFERENCE MONITORS

Each of the drivers is magnetically shielded so that the monitors are perfectly safe to

use near CRTs and TFT displays and each speaker uses a separate, highly ecient class-D

switching amplier.

Even cable lengths to and from the speaker enclosures have been kept short to reduce any

potential microphonic induction.

DSP Based Design

The use of a modern electronic architecture allows a much better audio performance to be

realised. The DSP-based, 3rd-order active crossover provides perfect separation between

mid-range and bass sounds.

A DSP-based electronic equalisation is used to atten the frequency response and also

enables the 5 band parametric EQ. Additionally, the fast-attack DSP loudspeaker limiter

protects the drivers from overload damage.

Audio Modiers

Six illuminated soft-touch pushbuttons allow front panel muting and dimming of the

loudspeakers., stereo-to-mono conversion., phase inversion and Middle+Side encoding/

decoding with all front panel settings stored in non-volatile memory which is recalled at

power-up. A universal power supply ensures global voltage operation without adjustment.

5 Band Parametric Equalisation

Each product in the Reference Monitor range contains an embedded 5 band parametric

equaliser.

On testing the units, they are set up to give a at response across the quoted frequency

range, but the parametric EQ allows you to alter the response either to account for poor

acoustics in the room that the monitor is mounted in, or to suit your particular listening

tastes.

Using the free of charge SCi remote control software, preset EQ settings can be selected, or

dierent EQ settings can be created and stored.

Front Panel Lock-Out

The controls on the front panel can optionally be locked out if required by using the free of

charge SCi remote control software.

Optional HD Expansion Cards

RM-HD1 HD-SDI expansion card &

RM-HDE1 HD-SDI & Dolby E Decoder expansion card

The HD-SDI video input expansion cards allow multiple AES groups embedded within an

HD-SDI or SD-SDI signal to be de-embedded and monitored, either as linear PCM with

Dolby E and Dolby Digital decoding (RM-HD1E), or as non-encoded linear PCM (RM-HD1).

The HD-SDI input is equalised, internally reclocked and re-transmitted to provide a

reclocked output to pass to external equipment via an output BNC connector, allowing the

reference monitor to be inserted into an HD-SDI chain.

Reference Monitors User Handbook

3

REFERENCE MONITORS RM-2S4 & RM-2S10

1

RM-2S4 Reference Monitor, 2 LED meters & 4 stereo

channel inputs

RM-2S10 Reference Monitor, 2 LED meters & 10 stereo

channel inputs

Introduction

The RM-2S4 and RM-2S10 are 1U rack-mount units oering quality loudspeaker monitoring

and accurate, high-resolution metering of up to four (RM-2S4) or twenty (RM-2S10 both

analogue and digital) stereo audio sources and more with the addition of optional

expansion cards. Sources may be in any mixture of analogue and AES/EBU digital formats,

with sample rates up to 192kHz accepted.

Sources (and additional Banks of Sources, if tted) are selected via a front panel rotary

encoder, with clear LED indication of the current selection. On the RM-2S10, the Source

LEDs also act as signal present indicators. A pair of line-level audio outputs, congurable

as analogue or AES/EBU digital, follow the selected source at either a xed level or one

mirroring the loudspeaker volume.

The level of the chosen source is displayed on a pair of bright, multicoloured 53-segment

bargraph meters, with a choice of seven accurately modelled scales/responses to suit

dierent applications and local preferences. A separate phase meter indicates channel

correlation or phase error conditions. On the rear panel, open-collector alarm outputs

provide hardware indication of sustained underlevel, overlevel, phase errors and digital

source lock.

Six illuminated pushbuttons provide access to a range of audio ‘modiers’ – instant

dimming of the volume, individual muting of each audio channel, stereo-to-mono

conversion, phase inversion and Middle+Side transcoding. On the rear panel, logic-level

inputs allow direct remote access to the DIM and MUTE functions.

The three-way loudspeaker system is fed via a DSP-based active crossover and a trio of

highly ecient Class-D ampliers. Careful attention to driver selection, materials and

case design, plus active DSP equalisation, has ensured a at response and outstanding

reproduction from such a shallow unit. A protective limiter prevents damage to the

loudspeakers under overload conditions and the front-panel headphone socket

automatically mutes the internal loudspeakers when a plug is inserted. A Balance control

allows you to alter the stereo imaging of the left and right channels.

Fig 1-1: RM-2S4 Reference Monitor Front Panel

Fig 1-2: RM-2S10 Reference Monitor Front Panel

4

Reference Monitors User Handbook

REFERENCE MONITORS RM-2S4 & RM-2S10

1

A further ve-band parametric equaliser can be accessed for room-equalisation purposes

via Sonifex SCi Windows-based remote control software. Source selection, status

monitoring and unit ID functions, plus rmware updates to add extra functionality, are

all accessible remotely via both USB and RS232 connections in conjunction with Sonifex

SCi software. The open control protocol also allows operation with terminal programs or

customised applications.

An optional addition to the RM-2S4 and RM-2S10 is an HD video input expansion

card, allowing multiple AES groups embedded within an HD-SDI or SD-SDI signal to be de-

embedded and monitored, (RM-HD1).

Both RM-2S4 and RM-2S10 units operate from global mains voltages (85-264V AC, 47-63Hz)

without adjustment.

System Block Diagram

Fig 1-3: Reference Monitor Block Diagram

Reference Monitors User Handbook

5

REFERENCE MONITORS RM-2S4 & RM-2S10

1

Front Panel Indicators & Controls

Fig 1-4: RM-2S4 Front Panel Controls

Fig 1-5: RM-2S10 Front Panel Controls

Power LED

The POWER LED illuminates whilst internal power is present within the unit. If this indicator

is not on, the most likely reason is simply the absence of mains power, but under fault

conditions it may also indicate a ruptured mains fuse or a problem with the internal power

supply module.

Rotary Source Selector

The rotary Source selector determines which of the four (RM-2S4) or ten (RM-2S10) stereo

audio inputs in the currently selected Bank is routed to the loudspeakers and metering.

Turning the selector anticlockwise increments the Source number and vice versa, with the

currently selected Source being indicated by illumination of the corresponding Source LED.

The currently selected Source can also be changed by the remote control ports (see the

relevant sections of this manual), & such changes will also be reected by the Source LEDs.

The Source selector is an endless rotary encoder; further rotation will be ignored once the

lowest/highest Source has been selected. If the currently selected Bank contains fewer

Fig 1-6: RM-2S4 Source Selector Fig 1-7: RM-2S10 Source Selector

6

Reference Monitors User Handbook

REFERENCE MONITORS RM-2S4 & RM-2S10

1

than four (RM-2S4) or ten (RM-2S10) Sources, it will not be possible to select

unimplemented Sources.

When mains power is removed, the currently selected Source is stored in non-volatile

memory and recalled instantly once power is restored.

Auto-Selection of Inputs

As standard, the RM-2S4 has auto-selection of the inputs, i.e. whichever analogue or digital

signal is connected to the input will be used. There is also an option (in the serial settings)

for the RM-2S10 to have auto-selection of it’s separate ten analogue inputs in Bank ANA

and ten digital inputs in Bank DIG. For users with a smaller number of mixed analogue and

digital sources, the auto-selection allows the unit to switch automatically between the

analogue and digital banks according to what is connected.

For the RM-2S10, with auto-selection enabled, both the Bank ANA and Bank DIG LEDs are

illuminated (expansion banks can still be selected as normal, if tted). If the current source

selection points to a valid digital input then the digital input will be selected. If it does not,

the similarly numbered analogue source will be used. If both are present then the digital

input takes precedence (hence auto-selection is only useful for a maximum of ten sources).

The analogue and digital presence indications are combined (ORed) and displayed

simultaneously.

Bank Selector

Pressing the Source selector knob inwards steps sequentially through all available input

Banks (groups of stereo inputs). Each press ashes the selected Bank LED and moves the

selected Bank onwards by one step. Once the last available Bank is selected, a further press

returns the selection to the rst available Bank. The currently selected Bank is indicated by

illumination of the corresponding Bank LED.

The currently selected Bank may also be changed via the remote control ports (see the

appropriate sections of this manual), and such changes will also be reected by the

Bank LEDs.

On the RM-2S4, BANK A corresponds to the four autoselecting (analogue or digital) stereo

inputs found on the rear panel, and further Banks become available with the addition of

optional expansion cards.

On the RM-2S10, separate Banks are provided for analogue (BANK ANA) and digital (BANK

DIG) sources – a total of twenty stereo sources may be attached if both Banks are fully

utilised. Further Banks become available with the addition of optional expansion cards. It is

not possible to select Banks which are not tted.

When mains power is removed, the currently selected Bank is stored in non-volatile

memory and recalled instantly once power is restored.

Reference Monitors User Handbook

7

REFERENCE MONITORS RM-2S4 & RM-2S10

1

Source Presence Indicators (RM-2S10 only)

On the RM-2S10, the presence of active audio on a Source input is indicated by green

illumination of the corresponding Source LED. The currently selected Source is indicated by

yellow illumination.

This feature may optionally be disabled through the use of the remote control OPT

command (see the appropriate section of this manual).

Main Meters

Fig 1-8: RM-2S4 & RM-2S10 Meters

The main meters are twin 53-segment, multicoloured LED bargraphs, displaying the

currently selected stereo audio source. The upper meter displays the left channel and the

lower meter the right channel.

By default, the meters reect exactly what is being heard from the loudspeakers including

any front panel signal modiers that are active, i.e. they are “output” meters. For example,

if Middle+Side processing is active (see the appropriate section of this manual), the upper

meter will display the Middle signal and the lower meter will display the Side. If the CUT

modier is used to mute an input channel, the corresponding meter will display no signal.

If preferred, the meters may be made to behave as “input” meters, i.e. not aected by front

panel signal modiers, through the use of the remote control OPT command (see the

appropriate section of this manual).

Several dierent characteristics are available for the meters to suit dierent applications

and regional preferences. The active meter characteristic is selected by the settings

of DIPSwitches 8, 9 and 10 on DIPSwitch Block 1 (found on the underside of the unit),

according to the following table.

8

Reference Monitors User Handbook

REFERENCE MONITORS RM-2S4 & RM-2S10

1

Fig 1-9: RM-2S4 & RM-2S10 DIPSwitch Settings

Note that power should be removed from the unit while making changes to the

conguration switches and reapplied once the changes are complete.

Meter

Characteristic

Scale Range*

Amber

Section

Starts at*

Red

Section

Starts at*

SW8 SW9 SW10

Dual PPM + VU -13 to +13dBu 0dBu +8dBu OFF OFF OFF

BBC PPM or EBU

PPM**

-13 to +13dBu 0dBu +8dBu ON OFF OFF

Nordic PPM -40 to +12dBu 0dBu +8dBu OFF ON OFF

AES Digital PPM -52 to 0dBFS -3dBFS 0dBFS ON ON OFF

DIN PPM -54 to +5dBu 0dBu +4dBu OFF OFF ON

Standard VU -24 to +3VU -4VU 0VU ON OFF ON

Extended VU -59 to +15VU -4VU 0VU OFF ON ON

Currently unused – do not select ON ON ON

* With 0dB of input gain selected.

** May be BBC or EBU PPM depending on the choice of scale plate.

1

ON DIP

2 3 4 5 6 7 8 9 10 11 12 1

ON DIP

2 3 4 5 6 7 8 9 10 11 12

1

ON DIP

2 3 4 5 6 7 8 9

10 11 12 1

ON DIP

2 3 4 5 6 7 8 9

10 11 12

Reference Monitor underside

DIPSwitch Block 1 DIPSwitch Block 2

Reference Monitors User Handbook

9

REFERENCE MONITORS RM-2S4 & RM-2S10

1

Meter Labelling

Each meter characteristic possesses dierent scaling, range and ballistics according to

the relevant British or International standards and self-adhesive scales for each of the

characteristics are supplied with the unit.

Fig 1-10: Meter Labelling Options

Once the desired meter characteristic has been chosen, proper scale labelling may be

ensured by removing the appropriate scale from the backing paper and applying it to the

recess provided between the two meters.

Brightness Control

The brightness of the bargraph meters and all other front panel indicators may be adjusted

to suit user preference or to match similar units nearby.

Fig 1-11: Brightness Control

A miniature at-bladed screwdriver inserted into the hole next to the BRIGHTNESS symbol

should be turned clockwise to increase the brightness or anti-clockwise to decrease it.

10

Reference Monitors User Handbook

REFERENCE MONITORS RM-2S4 & RM-2S10

1

PHASE Meter

The ve-segment LED phase meter indicates the average phase correlation

between the left and right channels of the currently selected stereo audio

source. It is labelled in both degrees of phase shift and amount of correlation.

The phase meter is an “output” meter, reecting exactly what is being heard

from the loudspeakers including any front panel signal modiers that are

active.

A monophonic signal fed to both channels of the selected Source will have

a correlation of 1.0, while inverting one such channel – making it perfectly

out of phase – gives a correlation of -1.0. True stereo signals will produce a

uctuating phase correlation.

Fig 1-12: Phase Meter Display

An interesting situation arises when only one channel of a stereo source is fed with signal.

If the unused channel is perfectly silent (as is possible in the case of a digital source) then

the phase correlation will average 0.0, but a small degree of crosstalk between the used

and unused channels (as is likely in the case of analogue sources) will allow the signal to

self-correlate and the meter will display an average correlation nearer 1.0.

BALANCE Control

The balance control is a centre-detented rotary

potentiometer allowing adjustment of the relative

balance between the left and right loudspeakers.

The control characteristic maintains a constant

overall power from the loudspeakers. Turning the

balance control fully to the left increases the volume

of the left-hand loudspeaker by 6dB and attenuates

the right by 6dB, and vice-versa.

LEVEL Control

The LEVEL, or volume, control is a rotary potentiometer allowing volume adjustment of the

internal loudspeaker system, the headphone output and optionally the line level outputs

(see Line Level Audio Outputs on page 17). A usable control range of 36dB is provided, and

with the volume control in the fully anti-clockwise position the signal is completely muted.

High input signal levels and/or high volume settings may result in activation of the

loudspeaker protection limiter (refer to the Limiter section of this manual).

Headphone Output

The front panel headphone output is a ¼” (6.35mm) stereo jack socket capable of

delivering over 80mW into 32Ω - 600Ω professional headphones at full volume. Higher

impedance headphones may be used at reduced levels. Lower impedance headphones

should not be used.

Fig 1-13: Balance Control

Page is loading ...

Sonifex RM-4C8 Reference Monitor Owner's manual

This manual is also suitable for

Sonifex RM-4C8 Reference Monitor Owner's manual

Related papers

Other documents