Allnet ALL500VDSL2 User manual

ALL500VDSL2

WLAN N VDSL Router

User´s Manual

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

NOTICE

This document contains proprietary information protected by copyright, and this Manual

and all the accompanying hardware, software, and documentation are copyrighted. All

rights are reserved. No part of this document may be photocopied or reproduced by

mechanical, electronic, or other means in any form.

The manufacturer does not warrant that the hardware will work properly in all

environments and applications, and makes no warranty or representation, either

expressed or implied, with respect to the quality, performance, merchantability, or

fitness for a particular purpose of the software or documentation. The manufacturer

reserves the right to make changes to the hardware, software, and documentation

without obligation to notify any person or organization of the revision or change.

All brand and product names are the trademarks of their respective owners.

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

Content

1. OVERVIEW .............................................................................................................................. 1

1.1 FEATURES ......................................................................................................................... 1

1.2 PACKET CONTENTS .......................................................................................................... 4

1.3 SYSTEM REQUIREMENTS .................................................................................................. 4

1.4 FACTORY DEFAULTS ......................................................................................................... 5

1.5 WARNINGS AND CAUTIONS ............................................................................................... 5

2 HARDWARE DESCRIPTION ................................................................................................. 6

3 HARDWARE INSTALLATION ............................................................................................... 7

4 PC CONFIGURATION GUIDE ............................................................................................... 8

4.1 LOCAL PC CONFIGURATION IN WINDOWS 95, 98, ME, XP ................................................ 8

4.2 LOCAL PC CONFIGURATION IN WINDOWS 2000 .................................................................. 9

5 WEB-BASED MANAGEMENT GUIDE ................................................................................... 9

5.1 LAN SETTING PAGE ............................................................................................................ 9

5.2 INTERNET ACCESS CONFIGURATION................................................................................ 10

5.3 WIRELESS SETTING .......................................................................................................... 27

APPENDIX: FREQUENT ASKED QUESTIONS ..................................................................... 32

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

1

1. Overview

Thank you for choosing our product. The ALL500VDSL2 is a Wireless VDSL router

combining a VDSL modem, an 802.11n wireless router, a 4-port switch in one unit,

bringing high-speed wireless Internet connection to a home or office.

1.1 Features

1.1.1 Data Rate

 Downstream data rate up to 100 Mbps

 Upstream data rate up to 50Mbps(100 Mbps upstream with

external AFE)

1.1.2 VDSL Compliant

 ITU G.992.1 (G.DMT)

 ITU G.993.2 (G.vdsl2) (Profile 8a, 8b, 8c, 8d, 12a,12b and 17a)

 ITU G.992.2 (G.Lite)

 ITU G.994.1 (G.hs)

 ITU G.992.3 (G.DMT.BIS)

 ITU G.992.4 (G.lite.bis)

 ITU G.992.5

 Compatible with all T1.413 issue 2 (full rate DMT over analog

POTS), and CO DSLAM equipment

1.1.3 Wireless

 Fully IEEE 802.11n compatible.

 Wireless data rate up to 300Mbps

 Operating in the unlicensed 2.4 GHz ISM band

 Multi-SSID

 Supports 64/128 bits WEP security and user authentication

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

2

1.1.4 Network Protocol & Features

 Ethernet to ADSL Self-Learning Transparent Bridging

 Internet Control Message Protocol (ICMP)

 IP Static Routing

 Routing Information Protocol (RIP, RIPv2)

 Network Address Translation (NAT)

 Virtual Server, Port Forwarding

 Dynamic Host Configuration Protocol (DHCP)

 DNS Relay, DDNS

 IGMP Proxy

 Simple Network Time Protocol (SNTP)

 VPN pass-through (IPSec/PPTP/L2TP)

 Parent control

1.1.5 ATM Capabilities

 RFC 1483 Multi-protocol over ATM ―Bridged Ethernet‖ compliant

 RFC 2364 PPP over ATM compliant

 RFC 2516 PPP over Ethernet compliant

 ATM Forum UNI3.1/4.0 PVC – Support up to 16 PVCs

 VPI Range: 0-255

 VCI Range: 32-65535

 UNI 3.0 & 3.1 Signaling

 ATM AAL5 (Adaption Layer type 5)

 OAM F4/F5

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

3

1.1.6 FIREWALL

 Built-in NAT

 MAC Filtering

 Packet Filtering

 Stateful Packet Inspection (SPI)

 Denial of Service Prevention (DoS)

 DMZ

1.1.7 Management Support

 Web Based GUI

 Upgrade or update via FTP/HTTP

 Command Line Interface via Telnet

 Diagnostic Test

 Firmware upgradeable for future feature enhancement

1.1.8 Operating System Support

 WINDOWS 98

 WINDOWS 98 SE

 WINDOWS ME

 WINDOWS 2000

 WINDOWS XP

 WINDOWS VISTA

 WINDOWS 7

 Macintosh

 LINUX

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

4

1.1.9 Environmental

 Operating humidity: 10%-90% non-condensing

 Non-operating storage humidity: 5%-95% non-condensing

1.2 Packet Contents

The packet contents are as the following:

 ADSL ROUTER x 1

 External Splitter x 1

 Power Adapter x 1

 Telephone Line x 1

 Ethernet Cable x 1

 Antenna x 2

 Base x 1

 CD x 1

1.3 System Requirements

Before using this ROUTER, verify that you meet the following requirements:

 Subscription for ADSL service. Your ADSL service provider should

provide you with at least one valid IP address (static assignment or

dynamic assignment via dial-up connection).

 One or more computers, each contains an Ethernet 10/100M Base-T

network interface card (NIC).

 A hub or switch, if you are connecting the device to more than one

computer.

 For system configuration using the supplied web-based program: A web

browser such as Internet Explorer v5.0 or later, or Netscape v4.7 or

later.

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

5

1.4 Factory Defaults

The device is configured with the following factory defaults:

 IP Address: 192.168.1.1

 Subnet Mask: 255.255.255.0

 User: admin

 Password: admin

 SSID: WLAN

 Encapsulation: RFC 2516 LLC

 VPI/VCI: According to local information

1.5 Warnings and Cautions

 Never install telephone wiring during storm. Avoid using a telephone

during an electrical storm. There might be a risk of electric shock from

lightening.

 Do not install telephone jacks in wet locations and never use the product

near water.

 To prevent dangerous overloading of the power circuit, be careful about

the designed maximum power load ratings. Not to follow the rating

guideline could result in a dangerous situation.

 Please note that telephone line on modem must adopt the primary line

that directly outputs from junction box. Do not connect Router to

extension phone. In addition, if your house developer divides a

telephone line to multi sockets inside the wall of house, please only use

the telephone that has connected with the splitter of ADSL Router when

you access the Internet.

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

6

2 Hardware Description

Front Panel

Rear panel

LED

Color

Function

PWR

Green

On: Power

Off: No power

LAN1,2,3,4

Green

On: LAN link established and active via LAN port

Blinking: DSL data activity occurs

Off: No LAN link via LAN port

WLAN

Green

On: The wireless module is ready and idle

Blinking: Data transmitting or receiving over

WLAN

Off: The wireless function is off

DSL

Green

On: DSL link established and active

Quick Blinking: DSL is trying to establish a

connection

Slow Blinking: No DSL link

INET

Green

Blinking: DSL data activity occurs

Off: No DSL data is being sent or received

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

7

Side panel

WIFI button: Enable or disable wireless function.

Reset button: System reset or reset to factory defaults.

WPS button: A convenient way for WPS set.

3 Hardware Installation

This chapter shows you how to connect Router. Meanwhile, it introduces the

appropriate environment for the Router and installation instructions.

1. Using a telephone line to connect the DSL port of ROUTER to the MODEM

port of the splitter, and using a other telephone line connect your telephone

to the PHONE port of the splitter, then connect the wall phone jack to the

LINE port of the splitter.

The splitter comes with three connectors as below:

LINE: Connects to a wall phone jack (RJ-11 jack)

MODEM: Connects to the DSL jack of ROUTER

PHONE: Connects to a telephone set

2. Using an Ethernet Cable to connect the LAN port of the ROUTER to your

LAN or a PC with network card installed.

Port

Function

DSL

Connect the device to an DSL telephone jack or

splitter using a RJ-11 telephone cable

LAN1,2,3,4

Connect the device to your PC's Ethernet port,

or to the uplink port on your hub/switch, using a

RJ-45 cable

ON/OFF

Switch it on or off

POWER

Connect to the supplied power adapter

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

8

3. Connect the power cable to the PWR connector on ROUTER, then plug in

the power adapter to the power outlet, and then press the on-off button.

Notes: Without the splitter and certain situation, transient noise from telephone

can interfere with the operation of the Router, and the Router may introduce

noise to the telephone line. To prevent this from happening, a small external

splitter must be connected to each telephone.

4 PC Configuration Guide

4.1 Local PC Configuration in Windows 95, 98, ME, XP

1. In the Windows task bar, click the ―Start‖ button, point to ―Settings‖, and

then click ―Control Panel‖.

2. Double-click the ―Network‖ icon.

3. On the ―Configuration‖ tab, select the TCP/IP network associated with your

network card and then click ―Properties‖.

4. In the ―TCP/IP Properties‖ dialog box, click the ―IP Address‖ tab. Set the IP

address as 192.168.1.x (x can be a decimal number from 2 to 254.) like

192.168.1.2, and the subnet mask as 255.255.255.0.

5. On the ―Gateway‖ tab, set a new gateway as 192.168.1.1, and then click

―Add‖.

6. Configure the ―DNS‖ tab if necessary. For information on the IP address of

the DNS server, please consult with your ISP.

7. Click ―OK‖ twice to confirm and save your changes.

8. You will be prompted to restart Windows. Click ―Yes‖.

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

9

4.2 Local PC Configuration in Windows 2000

1. In the Windows task bar, click the ―Start‖ button, point to ―Settings‖, and

then click ―Control Panel‖.

2. Double-click the ―Network and Dial-up Connections‖ icon.

3. In the ―Network and Dial-up Connections‖ window, right-click the ―Local

Area Connection‖ icon, and then select ―Properties‖.

4. Highlight ―Internet Protocol (TCP/IP)‖, and then click ―Properties‖.

5. In the ―Internet Protocol (TCP/IP) Properties‖ dialog box, set the IP address

as 192.168.1.x (x can be a decimal number from 2 to 254.), and the subnet

mask as 255.255.255.0 and the default gateway as 192.168.1.1. Then click

―OK‖.

6. Configure the ―DNS‖ tab if necessary. For information on the IP address of

the DNS server, please consult with your ISP.

7. Click ―OK‖ twice to confirm and save your changes.

5 Web-based Management Guide

In order to use the web-based management software it will be necessary to use

a computer that occupies the same subnet as the Router. The simplest way to

do this for many users will be to use DHCP server that is enabled by default on

the Router.

5.1 LAN setting page

Launch a web browser, such as Internet Explorer, and then use

http://192.168.1.1 to log on to the setting pages.

Click OK

Enter username

‘admin’ and password

‘admin’

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

10

5.2 Internet Access Configuration

5.2.1 ADSL Setup

From home page, you can find Advanced Setup option on the left router

configuration page.

1. From Layer2 Interface, click ATM Interface. you can set it up according to

the following steps. You Choose Add, or Remove to configure DSL ATM

interfaces.

2. Click Add to configure PVC identifier, select DSL latency and select

connection mode according to your local occasion. After the configuration,

you need to click Apply/Save.

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

11

3. Click WAN Service from the left menu.

4. Click Add to select a layer 2 interface for this service and then click Next.

5. Choose WAN service type, just choose PPPoE for example here. You can

enter your own service description here if you want and then click Next.

6. Input PPP Username & PPP Password and then click Next. The user

interface allows a maximum of 256 characters in the user name and a

maximum of 32 characters in the password.

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

12

PPPoE service name can be blank unless your Internet Service Provider gives you a

value to enter.

Authentication method is default to Auto. It is recommended that you leave the

Authentication method in Auto, however, you may select PAP or CHAP if

necessary. The default value for MTU (Maximum Transmission Unit) is 1500 for

PPPoA and 1492 for PPPoE. Do not change these values unless your ISP asks you

to.

Enable Full Cone NAT: In full cone NAT, all requests from the same private IP

address and port are mapped to the same public source IP address and port.

Someone on the Internet only needs to know the mapping scheme in order to send

packets to a device behind the VDSL Device.

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

13

The gateway can be configured to disconnect if there is no activity for a specific period

of time by selecting the Dial on demand check box and entering the Inactivity

timeout. The entered value must be between 1 minute and 4320 minutes.

Use Static IPv4 address: If the ISP gave you a static (fixed) IP address, select this

option and enter it in the IP Address field. If the ISP did not give you a static IP

address, clear the Use Static IP Address option. The ISP automatically assigns the

WAN connection an IP address when it connects.

Enable PPP Debug Mode: Select this to turn on the debug mode for the PPP

connection.

Bridge PPPoE Frames Between WAN and Local Ports: In addition to the VDSL

Device's built-in PPPoE client, you can enable this to pass PPPoE through in order to

allow LAN hosts to use PPPoE client software on their computers to connect to the

ISP via the VDSL Device. Each host can have a separate account and a public WAN

IP address. PPPoE pass through is an alternative to NAT for applications where NAT

is not appropriate. Disable PPPoE pass through if you do not need to allow hosts on

the LAN to use PPPoE client software on their computers to connect to the ISP.

The PPP IP Extension is a special feature deployed by some service providers.

Unless your service provider specifically requires this setup, do not select it. If you

need to select it, the PPP IP Extension supports the following conditions:

 It allows only one computer on the LAN.

 The public IP address assigned by the remote using the PPP/IPCP

protocol is actually not used on the WAN PPP interface. Instead, it

is forwarded to the computer's LAN interface through DHCP. Only

one system on the LAN can be connected to the remote, since the

DHCP server within the ADSL gateway has only a single IP

address to assign to a LAN device.

 NAPT and firewall are disabled when this option is selected.

 The gateway becomes the default gateway and DNS server to the

computer through DHCP using the LAN interface IP address.

 The gateway extends the IP subnet at the remote service provider to

the LAN computer. That is, the PC becomes a host belonging to the

same IP subnet.

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

14

 The ADSL gateway bridges the IP packets between WAN and LAN

ports, unless the packet is addressed to the gateway's LAN IP

address.

7. Select a preferred wan interface as the system default gateway.

8. Get DNS server information from the selected WAN interface or enter static DNS

server IP addresses. If only a single PVC with IPoA or static MER protocol is

configured, you must enter static DNS server IP addresses.

9. Make sure that the settings below match the settings provided by your ISP. Click

on the Apply/Save button to save your configurations.

5.2.2 VDSL Setup

From home page, you can find Advanced Setup option on the left router

configuration page.

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

15

1. From Layer2 Interface, click PTM Interface. you can set it up according to

the following steps. You Choose Add, or Remove to configure DSL PTM

interfaces.

2.Click Add to configure PTM Priority, select DSL latency and select connection

mode according to your local occasion. After the configuration, you need to click

Apply/Save.

3. Click WAN Service from the left menu.

4.Click Add to select a layer 2 interface for this service and then click Next.

5. Choose WAN service type, just choose PPPoE for example here. You can

enter your own service description here if you want and then click Next.

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

16

6. Input PPP Username & PPP Password and then click Next. The user

interface allows a maximum of 256 characters in the user name and a maximum

of 32 characters in the password.

ALL500VDSL2 WLAN N VDSL Router Allnet GmbH

17