BEA SuperScan-T Q-Disconnect User guide

Category
Motorcycle Accessories
Type
User guide
©BEA | Original Instructions
75.5912.02 SUPERSCAN-T QUICK-DISCONNECT 20190312 Page 1 of 2
SMP
plug
1
2 4
3
SUPERSCAN-T QUICK DISCONNECT HARNESS
20.5383
96 in (8 ft)27 in
ENGLISH
DESCRIPTION
Visit website for available
languages of this
document.
See tables below for wire
colors and corresponding
functions.
APPROACH
1. approach wire harness
segment (27“)
2. safety wire harness
segment (27“)
3. sheath (26“)
4. quick disconnect
SMR
plug
SMP
plug
SAFETY
2. After routing the quick-disconnect cable, attach the Approach segment
to the approach-side SUPERSCAN-T, and the Safety segment to the
safety-side SUPERSCAN-T as follows:
3. Attach the other end of the quick-disconnect cable to the door
control as follows:
1. Perform a SUPERSCAN-T installation as normal (per User’s Guide 75.5911). When performing the cabling installation, follow the same cable routing guidelines
that are provided in the User’s Guide, using the SUPERSCAN-T quick-disconnect cable in lieu of the standard cable.
WIRE COLOR CONTROL CONNECTION
(or other function)
red POWER (+) : 12 – 24 VAC/VDC ±10%
black POWER (-) : 12 – 24 VAC/VDC ±10%
white COMMON input at door control (for activation)
green ACTIVATION input at door control
white/red COMMON input at door control (for safety)
green/red SAFETY input at door control
orange INHIBIT +
brown INHIBIT ground
purple TEST (-)
purple/yellow TEST (+)
TERM. APPROACH
WIRE COLOR
SAFETY
WIRE COLOR
FUNCTION
1 purple/yellow purple/yellow TEST (+)
2 purple purple & brown GROUND
3 [not used] orange INHIBIT (+)
4
1,3
[not used] [not used] NORMALLY OPEN
5
2,3
green green/red NORMALLY CLOSED
6 white white/red COMMON
7 black black POWER (-)
8 red red POWER (+)
INSTALLATION & WIRING
©BEA | Original Instructions
75.5912.02 SUPERSCAN-T QUICK-DISCONNECT 20190312 Page 2 of 2
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
-
-
+
+
To inhibit a SUPERSCAN-T, an external, dry-contact, switching device is required which changes state at the point of desired inhibition
on the respective SUPERSCAN-T. Each SUPERSCAN-T may be independently inhibited; however, a switching device will be required
for each (i.e. auxiliary micro-switch on the operator). To enable the inhibiting circuit, perform the following:
ALTERNATE METHOD OF INHIBITING:
Break one leg of output relay circuit.
INHIBIT WITH VOLTAGE:
INHIBITING A SUPERSCAN-T
COM and N.O. dry-contact switches
to a closed contact state at the point
of desired inhibition of the respective
SUPERSCAN-T
COM and N.C. dry-contact switches
to an open contact state at the point
of desired inhibition of the respective
SUPERSCAN-T
POWER
POWER
red
orange
black
brown
red
white/red
black
green/red
BEA, the sensor manufacturer, cannot be held responsible for incorrect installations or inappropriate adjustments of the sensor/device; therefore, BEA
does not guarantee any use of the sensor outside of its intended purpose.
BEA strongly recommends that installation and service technicians be AAADM-certifi ed for pedestrian doors, IDA-certifi ed for doors/gates, and factory-
trained for the type of door/gate system.
Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor
system installation is compliant with local, national, and international regulations, codes, and standards.
Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer recommendations
and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must be performed during each service
call – examples of these safety inspections can be found on an AAADM safety information label (e.g. ANSI/DASMA 102, ANSI/DASMA 107).
Verify that all appropriate industry signage and warning labels are in place.
BEA INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS
Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462 | General Tech Questions: T[email protected] | Tech Docs: www.BEAinc.com
  • Page 1 1
  • Page 2 2

BEA SuperScan-T Q-Disconnect User guide

Category
Motorcycle Accessories
Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI