2. Axxess
  3. LD-AX-XSVI-AU1

Axxess LD-AX-XSVI-AU1, LD-AX-XSVI-AU2, XSVI-9004-NAV Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Axxess LD-AX-XSVI-AU1 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
INSTALLATION INSTRUCTIONS FOR PART XSVI-9004-NAV
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
• Providesaccessory(12-volt10-amp)
• RetainsR.A.P.(retainedaccessorypower)
• ProvidesNAVoutputs(parkingbrake,reverse,andspeedsense)
• PrewiredASWC-1harness(ASWC-1soldseparately)
• Retainsbalanceandfade
• Micro“B”USBupdatable
FEATURES
• Cuttingtool•Crimpingtool•Tape•Connectors
(example:butt-connectors,bellcaps,etc.)
TOOLS REQUIRED
Audi CAN
Interface
2002-2013
XSVI-9004-NAV
APPLICATIONS
• XSVI-9004interface•LD-AX-XSVI-AU1harness•LD-AX-XSVI-AU2harness
INTERFACE COMPONENTS
AUDI
Applications below use
LD-AX-XSVI-AU1:
A3* 2006-2013
A4/RS4/S4with NAV 2005-2008
A4/RS4/S4 2007-2008
A4/RS4/S4* 2006
TT 2008-2013
Applications below use
LD-AX-XSVI-AU2:
A3** 2006-2007
A4/S4*** 2002-2006
A6 2004
allroad 2004-2005
TT 2002-2006
Note:
* Only for models with either a
Symphony Plus or NAV radio **
With Concert radio (without NAV) ***
With Symphony radio
(without NAV)
XSVI-9004-NAV
From the LD-AX-XSVI-AU1 harness to the aftermarket radio
(a) From the 12-pin harness:
• ConnecttheRedwiretotheaccessorywire.
• ConnecttheOrangewiretotheilluminationwire,iftheaftermarketradiohas
noilluminationwire,tapeofftheOrangewire.
• ConnecttheBlue/Whitewiretotheampturnonwire(thiswiremustbe
connectedtohearsoundfromthefactoryamplifier).
Note: There is a Blue wire on the 40-pin harness to connect as well.
Thefollowingwiresareforaftermarketmultimedia/navigationradiosthatprovide
thesewires(ifnotrequired,tapethemoffanddisregardthem):
• ConnecttheLight Greenwiretotheparkingbrakewire(ifapplicable).
• ConnecttheGreen/Purplewiretothereversewire(ifapplicable).
• TheBlue/Pinkwirewillnotbeused,tapeitoffanddisregardit.
Note: This wire will be on the 40-pin harness instead.
(b) From the 40-pin harness:
• ConnecttheBlackandBlack/Whitewirestothegroundwire.
• ConnecttheYellow wiretothebatterywire.
• ConnecttheBluewiretotheampturnonwire(thiswiremustbeconnected
tohearsoundfromthefactoryamplifier).
Thefollowingwireisforanaftermarketmultimedia/navigationradiothat
providesthiswire,ifnotrequired,tapeitoffanddisregardit:
• ConnecttheBlue/Pinkwiretothespeedsensewire(V.S.S.),ifapplicable.
For non-BOSE systems:
• Disregardthe WhiteRCA,itwillnotbeusedinthisapplication.
• DisregardtheGrayRCA,itwillnotbeusedinthisapplication.
• ConnecttheGreenRCAtotheleftrearRCAoutput.
• ConnectthePurple RCAtotherightrearRCAoutput.
• ConnecttheWhitewiretotheleftfrontpositivespeakeroutput.
• ConnecttheWhite/Blackwiretotheleftfrontnegativespeakeroutput.
• ConnecttheGray wiretotherightfrontpositivespeakeroutput.
• ConnecttheGray/Blackwiretotherightfrontnegativespeakeroutput.
Tapeoffanddisregardthefollowingwires,theywillnotbeusedin
thisapplication:
• TheGreen,Green/Black,Purple,Purple/Blackwires.
Connections to be made
XSVI-9004-NAV
Connections to be made
For BOSE systems:
• ConnecttheWhiteRCAtotheleftfrontRCAoutput.
• ConnecttheGrayRCAtotherightfrontRCAoutput
• ConnecttheGreenRCAtotheleftrearRCAoutput.
• ConnectthePurpleRCAtotherightrearRCAoutput
Tapeoffanddisregardthefollowingwires,theywillnotbeusedin
thisapplication:
• TheGreen,Green/Black,Purple,Purple/Black,White,White/Black,Gray,
andGray/Blackwires.
Note: It is highly recommended that the radio being used has 2 sets
of RCA outputs to retain balance and fade; 3 sets if a sub-woofer amplifier
will be added.
(c) From the 12-pin harness (ASWC-1 pre-wired harness):
• ThisharnessistobeusedinconjunctionwiththeoptionalASWC-1
(notincluded)toretainsteeringwheelcontrols.IftheASWC-1isnotbeing
used,disregardthisharness.Ifitwillbeused,pleaserefertotheASWC-1
instructionsforradioconnectionsandprogramming.
Note: Disregard the harness that comes with the ASWC-1.
Withthekeyintheoffposition:
• Connectthe12-pinharnessintotheinterface.
• Connectthe40-pinharnessintothevehicle.
• Withallconnectionscompleted,reconnectthenegativebatteryterminal.
• Initializetheinterfacebyturningtheignitiononfor30seconds,thenturnthe
ignitionbackoff,thenbackonagain.
Note: If using the ASWC-1, connect it after you initialize the XSVI-9004-NAV, with
the key in the off position.
Installing the XSVI-9004-NAV
• IfthevehiclehasenginenoiseafterinstallingtheXSVI-9004-NAV,useAxxess
partnumberAX-AGL610,qty.(2).
Troubleshooting
XSVI-9004-NAV
From the LD-AX-XSVI-AU2 harness to the aftermarket radio
(a) From the 12-pin harness:
• ConnecttheRedwiretotheaccessorywire.
• ConnecttheOrangewiretotheilluminationwire,iftheaftermarketradiohas
noilluminationwire,tapeofftheOrangewire.
Thefollowingwiresareforaftermarketmultimedia/navigationradiosthatprovide
thesewires(ifnotrequired,tapethemoffanddisregardthem):
• ConnecttheLight Greenwiretotheparkingbrakewire(ifapplicable).
• ConnecttheGreen/Purple wiretothereversewire(ifapplicable).
• Connectthe Blue/Pink wiretothespeedsense(V.S.S.)wire(ifapplicable).
(b) From the 16-pin harness:
• ConnecttheBlackwiretothegroundwire.
• ConnecttheYellowwiretothebatterywire.
For non-BOSE systems:
• ConnecttheWhitewiretotheleftfrontpositivespeakeroutput.
• ConnecttheWhite/Blackwiretotheleftfrontnegativespeakeroutput.
• ConnecttheGray wiretotherightfrontpositivespeakeroutput.
• ConnecttheGray/Blackwiretotherightfrontnegativespeakeroutput.
Tapeoffanddisregardthefollowingwires,theywillnotbeusedin
thisapplication:
• TheGreen,Green/Black,Purple,Purple/Blackwires.
For BOSE systems:
Tapeoffanddisregardthefollowingwires,theywillnotbeusedin
thisapplication:
• TheGreen,Green/Black,Purple,Purple/Black,White,White/Black,Gray,
andGray/Blackwires.
(c) From the 26-pin harness:
• Connectthe Blue/White wiretotheampturnonwire(thiswiremustbe
connectedtohearsoundfromthefactoryamplifier).
For non-BOSE systems:
• DisregardtheWhite RCA,itwillnotbeusedinthisapplication.
• DisregardtheGrayRCA,itwillnotbeusedinthisapplication.
• ConnecttheGreenRCAtotheleftrearRCAoutput.
Connections to be made
XSVI-9004-NAV
Connections to be made
• ConnectthePurpleRCAtotherightrearRCAoutput.
For BOSE systems:
• ConnecttheWhiteRCAtotheleftfrontRCAoutput.
• ConnecttheGray RCAtotherightfrontRCAoutput
• Connectthe Green RCAtotheleftrearRCAoutput.
• ConnectthePurple RCAtotherightrearRCAoutput
Note: It is highly recommended that the radio being used has 2 sets of RCA
outputs to retain balance and fade; 3 sets if a subwoofer amplifier will be
added.
(d) From the 12-pin harness (ASWC-1 pre-wired harness):
• ThisharnessistobeusedinconjunctionwiththeoptionalASWC-1(not
included)toretainsteeringwheelcontrols.IftheASWC-1isnotbeing
used,disregardthisharness.Ifitwillbeused,pleaserefertotheASWC-1
instructionsforradioconnectionsandprogramming.
Note: Disregard the harness that comes with the ASWC-1.
Withthekeyintheoffposition:
• Connectthe12-pinharnessintotheinterface.
• Connectthe16-pinharnessintothevehicle.
• Connectthe26-pinharnessintothevehicle.
• Withallconnectionscompleted,reconnectthenegativebatteryterminal.
• Initializetheinterfacebyturningtheignitiononfor30seconds,thenturnthe
ignitionbackoff,thenbackonagain.
Note: If using the ASWC-1, connect it after you initialize the XSVI-9004-NAV, with
the key in the off position.
Installing the XSVI-9004-NAV
• IfthevehiclehasenginenoiseafterinstallingtheXSVI-9004-NAV,useAxxess
partnumberAX-AGL610,qty.(2).
Troubleshooting
/