Toshiba E-Studio 18 Quick Manual

Toshiba
Brand
Toshiba
Model
E-Studio 18
Category
Laser/LED printers
Type
Quick Manual
Printed in China 1BV0805801
R110520J8500-TTEC OME11004700 DP-1800 2011-07
©2011 TOSHIBA TEC CORPORATION All rights reserved
Poor quality printing such as uneven and soiled images can be improved by
simple cleaning. We recommend you to clean the equipment.
Troubleshooting
When a problem is detected
On bypass tray
Behind transfer unit
Within fuser unit
Regular cleaning
Toner empty
Paper jams
1010
2
3
1
8
10
9
11
12
13
4
5
6
7
1
2 3
8
1
2
4
6
5
3
7
CALL FOR SERVICE C##
123456789
OPEN SIDE COVER
PAPER JAM E13
1
5
User's Guide: Chapter 6
User's Guide: Chapter 6
User's Guide: Chapter 6
User's Guide: Chapter 7
Basic Operations
Before Use
This guide describes general precautions, preparation, basic operation, and troubleshooting of the equipment. Before using the equipment,
be sure to read the Safety Information (Printouts) at rst. The CD-ROM contains this Quick Guide in other languages.
Trademarks
Company names and product names in this manual are the trademarks of their respective companies.
MULTIFUNCTIONAL DIGITAL SYSTEMS
General Precautions
Quick Guide
When using the equipment
WARNING
Do not take o the cover of the equipment; otherwise you could
be injured or get an electric shock.
Do not remove or connect the plug with wet hands, as this could
give you an electric shock.
Do not place any container with liquid (ower vases, coee cups,
etc.) on or near the equipment. This could cause a re or give you
an electric shock.
Keep paper clips and staples away from the air vent. If not, a re
could result or you could get an electric shock.
If the equipment becomes excessively hot, smoke comes out of it
or there is an odd smell or noise, proceed as follows. Turn the
power OFF and remove the plug from the outlet, then contact
your service representative.
If the equipment will not be used for more than one month,
remove the plug from the outlet for safety purposes during that
time. If an insulation failure occurs, this could cause a re or give
you an electric shock.
CAUTION
Do not place heavy objects (4 kg/9 lb. or more) on the original
glass and do not press on it with force. Breaking the glass could
cause personal injury.
Do not place heavy objects (4 kg/9 lb. or more) on the equipment.
If the objects fall o, this could cause injury.
Be careful not to let your ngers be caught when closing the
drawer. This could injure you.
Do not touch the fuser unit or the metal area around it. Since
they are very hot, you could be burned or the shock could cause
you to get your hand injured in the machine.
Be careful not to let your ngers be caught between the
equipment and the side cover. This could injure you.
•
•
•
•
•
•
•
•
•
•
•
Other points
Do not turn the power OFF with jammed paper left inside the equipment. This
could cause malfunctions when the main switch is turned ON next time.
Be sure to turn the power OFF when leaving the oce or if there is a power
failure.
Be careful because the paper exit area and paper just after exiting are hot.
When handling supplies
WARNING
Never attempt to incinerate toner cartridges. This could cause an
explosion. Do not dispose of used toner cartridges. Contact your
service representative.
Other points
Read this manual carefully to replace the toner cartridge using the correct
procedure. An improper procedure could cause toner leakage or scattering.
Do not open the toner cartridge forcibly. This could cause toner leakage or
scattering.
Keep the toner cartridge out of the reach of children.
If toner is spilt on your clothes, wash it o with cold water. Your clothes will be
stained with toner and it will not come out if you use warm water.
If toner leaks from the toner cartridge, be careful not to inhale or touch it.
First-aid measures
If you inhale or touch toner, etc; carry out the following treatment.
Inhalation: Remove from exposure area to fresh air immediately. Contact a
physician if there is any diculty in breathing or other signs of distress.
Skin Contact: Wash with soap and water. Wash clothing before reuse. If irritation
occurs or is persistent, seek medical attention.
Eye Contact: Immediately ush eyes with plenty of water for at least 15 minutes.
If irritation persists, call a physician.
Ingestion: Dilute stomach contents with several glasses of water.
•
•
•
•
•
•
•
•
•
•
•
•
Original glass
Front cover
DrawerExit support tray
Toner cartridge
Receiving tray
USB terminal
(4-pin)
AC-IN terminal
(Back side)
Platen cover
Original scale
Platen sheet
Side cover
Bypass tray
Press the power switch to “ ” (ON) side.
To turn the power o
Press the power switch to “ ” (OFF) side.
Installing the driver requires the administrator authority.
In Windows 7 or Windows Server 2008 R2, be sure to use the
installer to install the drivers.
Using installer
1. Insert the CD-ROM into the CD-ROM drive of the computer.
2. Double-click [Setup.exe] on the CD-ROM.
3. Follow the instructions of the installer.
Using Plug and Play
1. Connect the equipment to the computer using a USB cable,
and then start the computer.
2. Turn on the power of the equipment.
3. Follow the dialog of the operation system.
Note for installing from installer
Do not connect the USB cable to the equipment until the instruction
appears.
Exit all running applications, if any.
If the [User Account Control] window appears, click [Allow],
[Continue] or [Yes] on Step 2.
•
•
•
Bypass tray
To set paper size and paper type
[MENU] button → [PAPER SETTINGS]
1. Raise the platen cover.
1. Select [Print] in the [File] menu of the application.
1. Raise the platen cover.
2. Place the original face down on the original glass and align it
against the left rear corner.
3. Run your TWAIN-compatible application and execute the
image acquisition command from within the application.
4. Click [Scan] to scan the original.
5. Save the scanned image in your application.
Now printer
and scanner
functions are
available.
Drawer
Control panel
Turning power ON
4.
1
Set the desired number of
copies with the button and the
button , and then
2
press the
[START] button.
Copying starts.
To stop copying and reset settings and LCD screen
[CLEAR/STOP] button
Shortcut keys
button
Press: Except Europe “ID CARD”, Europe “DENSITY”
Press 1 sec.: “FUNCTION 1”
(Default: Except Europe “DENSITY”, Europe “ID
CARD”)
button
Press: “ORIGINAL MODE”
Press 1 sec.: “FUNCTION 2” (Default: “ZOOM”)
2.
1
Select the printer driver of
the equipment , and then
2
click [Preferences] ([Properties])
as required.
3. Set the print options as required and click [OK].
4. Click [Print] ([OK]).
Printing starts.
Before Use Basic Operations
General Precautions Troubleshooting
Alert lamp LCD screen
[SETTING/OK] button
[MENU] button
[CLEAR/STOP] button
[START] button
Basic screen
1
READY
DRAWER:A4-R
AUTO
100%
TEXT/PHOTO
Message
Paper size
Information icon
Reproduction ratio
Density
Original mode
Setting icon
Cursor icon
Copy quantity
Set number
of copies
button button
button
button
Component description
User's Guide: Chapter 1
Driver installation
User's Guide: Chapter 1
Loading paper
User's Guide: Chapter 1
1
2
4
5
3
1
1
2
Copier
User's Guide: Chapter 2
2. Place the original with its face
down on the original glass and
align it against the left rear corner.
3. Press the [SETTING/OK] button
and specify the copy setting as
required.
2
1
Printer
User's Guide: Chapter 3
Scanner
User's Guide: Chapter 4
Connecting computer
Connect the equipment to the computer using a USB cable.
Use a type A (4 pin, male) to type B (4 pin, male) USB cable.
READY
DRAWER:A4-R
200%
AUTO
TEXT
1
  • Page 1 1
  • Page 2 2

Toshiba E-Studio 18 Quick Manual

Toshiba
Brand
Toshiba
Model
E-Studio 18
Category
Laser/LED printers
Type
Quick Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents