Optimus IA-10SIP is a device that enables integration of audio equipment with Voice over Internet Protocol (VoIP). It has various capabilities that allow for flexible use in different scenarios. Here are some key features and possible use cases of the Optimus IA-10SIP:
- Unidirectional communication: The Optimus IA-10SIP can be used as a receiver of audio streams from other SIP devices. It converts the received audio into an analog signal that can be connected to speakers or amplifiers. This allows for integration of traditional audio systems with VoIP networks, enabling remote announcements or music playback.
Optimus IA-10SIP is a device that enables integration of audio equipment with Voice over Internet Protocol (VoIP). It has various capabilities that allow for flexible use in different scenarios. Here are some key features and possible use cases of the Optimus IA-10SIP:
- Unidirectional communication: The Optimus IA-10SIP can be used as a receiver of audio streams from other SIP devices. It converts the received audio into an analog signal that can be connected to speakers or amplifiers. This allows for integration of traditional audio systems with VoIP networks, enabling remote announcements or music playback.
GUÍA RÁPIDA
IA-10SIP Versión 1.0 1/2
IA-10SIP
A
TENCI
Ó
N:
Antes de conectar el equipo asegúrese que la tensión
de suministro sea la adecuada.
No exponga el equipo a fuentes de calor.
La instalación debe ser realizada por personal técnico
cualificado.
INTERFAZ AUDIO IP SIP
ESPECIFICACIONES
Alimentación POE / 5 Vcc
Consumo 10 W Máx.
Dimensiones 214 x 105 x 41 mm
Peso 0,8 kg
Acabado Hierro pintado negro RAL9005
Accesorios
(no incluidos)
Z-112 Kit montaje en rack 1 unidad
Z-113 Kit montaje en rack 2 unidades
1. Contacto de salida por relé. Se cerrará a masa al recibir un tono DTMF previamente programado. Máx 24 V, 2 A.
2. Contacto de Salida PRI. Colector abierto. Se activará siempre que una llamada esté activa.
3. Salida Audio Nivel Micro -60 dB.
4. Salida Audio Nivel Aux 0 dB.
5. Salida audio 8 Ω 2 W.
6. Entrada alimentación 5 Vcc.
7. Conector Ethernet POE.
8. LED Power. Indicador de alimentación.
9. LED Calling. Parpadeará durante el establecimiento de llamada, quedará fijo durante la llamada.
10. LED audio out. Indicador de nivel de audio de salida.
GUÍA RÁPIDA
IA-10SIP Versión 1.0 2/2
EJEMPLOS DE CONEXIÓN
INTERFAZ AUDIO IP SIP
CONFIGURACIÓN
El equipo no dispone de ningún tipo de configuración por hardware. Todos los parámetros del equipo: IP, extensión, volumen... se configuran
desde su servidor web. Para más detalle, consulte el manual “Optimus SIP web server configuration”.
(http://www.optimusaudio.com/arxius/i_tecnica/Optimus%20SIP%20web%20Server%20configuration%20ENG%20V1.1.pdf).
Para el correcto funcionamiento del equipo deben configurase los LED de la siguiente manera:
Status Light LED1: Lit When call is successful, Blink When call is in progress
Status Light LED2: Lit When call is successful, Blink Unused
Comunicación unidireccional, IA-10SIP como receptor. Recibe llamadas desde otro dispositivo SIP y las convierte a audio analógico. Se conecta
directamente a un altavoz de 8 Ω, o a un amplificador mediante una entrada de micro (-60 dB) o de auxiliar (0 dB).
QUICK GUIDE
IA-10SIP Version 1.0 1/2
IA-10SIP
A
TTENTION:
Make sure the power source conforms to the power
requirements before connecting the equipment.
Do not install the unit near heat sources.
Only qualified service personnel should be allowed to
install and operate the unit.
IP SIP AUDIO INTERFACE
SPECIFICATIONS
Power supply POE / 5 Vdc
Consumption 10 W Máx.
Dimensions 214 x 105 x 41 mm
Weight 0.8 kg
Finish Black painted iron RAL9005
Accessories
(not included)
Z-112 Rack mounting kit for 1 unit
Z-113 Rack mounting kit for 2 units
1. Relay output contact. The contact is activated when it receives a DTMF tone previously programmed. Max 24 V, 2 A.
2. PRI output contact. Open collector. It remains activated while call is active.
3. Microphone Audio Output -60 dB.
4. Aux Audio Output 0 dB.
5. Speaker audio output 8 Ω 2 W.
6. Power supply input 5 Vdc.
7. Ethernet POE connector.
8. Power LED indicator.
9. Calling LED indicator. It blinks during call establishment and it remains lit when call is successful.
10. Audio output LED indicator. Audio output level indicator.
QUICK GUIDE
IA-10SIP Version 1.0 2/2
CONNECTION EXAMPLES
IP SIP AUDIO INTERFACE
CONFIGURATION
There is not any kind of hardware configuration. All device parameters: IP, extension, volume... are configured from unit’s Web Server. For more
detail, refer to "Optimus SIP web server configuration" instruction manual.
(http://www.optimusaudio.com/arxius/i_tecnica/Optimus%20SIP%20web%20Server%20configuration%20ENG%20V1.1.pdf).
For a proper operation of the device, you need to configure the LEDs as follow:
Status Light LED1: Lit When call is successful, Blink When call is in progress
Status Light LED2: Lit When call is successful, Blink Unused
Unidirectional communication, IA-10SIP as receiver. It receives calls from another SIP device and converts them to analogue audio. It can be
connected directly to an 8 Ω speaker, or to an amplifier using mic (-60 dB) or auxiliary (0 dB) inputs.
-
1
-
2
-
3
-
4
Optimus IA-10SIP is a device that enables integration of audio equipment with Voice over Internet Protocol (VoIP). It has various capabilities that allow for flexible use in different scenarios. Here are some key features and possible use cases of the Optimus IA-10SIP:
- Unidirectional communication: The Optimus IA-10SIP can be used as a receiver of audio streams from other SIP devices. It converts the received audio into an analog signal that can be connected to speakers or amplifiers. This allows for integration of traditional audio systems with VoIP networks, enabling remote announcements or music playback.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- español: Optimus IA-10SIP Manual de usuario
Related papers
Other documents
-
Zenith C30W46 User manual
-
Harris RF-3200 User manual
-
-
Hager RTN301X User manual
-
LG Electronics 30FZ4D User manual
-
DoorBird DB-D101S Owner's manual
-
Polycom RMX 1000 Quick start guide
-
Leviton INDS1-S Specification
-
Tiptel 360 ip User manual
-
Yealink SIP-T58A with camera & SIP-T58A Quick start guide