Intel D510MO User manual

Brand: Intel

Model: D510MO

Category: Motherboards

Type: User manual

Page is loading ...

Revision History

Revision Revision History Date

-001 First release of the Intel

Desktop Board D510MO Product

Guide

September 2009

If an FCC declaration of conformity marking is present on the board, the following statement applies:

FCC Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

For questions related to the EMC performance of this product, contact:

Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124,

1-800-628-8686

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the

user’s authority to operate the equipment.

Tested to comply with FCC standards for home or office use.

Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set

out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux

appareils numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par

le ministére des Communications du Canada.

Disclaimer

Information in this document is provided in connection with Intel

products. No license, express or implied,

by estoppel or

otherwise, to any intellectual property rights is granted by this document. Except as provided

in Intel’s Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel

disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or

warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent,

or life sustaining applications. Intel may make changes to specifications and product descriptions at any

time, without notice.

Intel Desktop Board D510MO may contain design defects or errors known as errata which may cause the

product to deviate from published specifications. Current characterized errata are available on request.

Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing

your product order.

Copies of documents which have an ordering number and are referenced in this document, or other Intel

literature, may be obtained from Intel Corporation by going to the World Wide Web site at:

http://www.intel.com/ or by calling 1-800-548-4725.

Intel, the Intel logo, and Intel Atom are trademarks of Intel Corporation in the U. S. and other countries.

* Other names and brands may be claimed as the property of others.

iii

Preface

This Product Guide gives information about board layout, component installation, and

regulatory requirements for Intel

Desktop Board D510MO.

Intended Audience

The Product Guide is intended for technically qualified personnel. It is not intended for

general audiences.

Intended Uses

All Intel

Desktop Boards are evaluated as Information Technology Equipment (I.T.E.)

for use in personal computers (PC) for installation in homes, offices, schools, computer

rooms, and similar locations. The suitability of this product for other PC or embedded

non-PC applications or other environments, such as medical, industrial, alarm systems,

test equipment, etc. may not be supported without further evaluation by Intel.

Document Organization

The chapters in this Product Guide are arranged as follows:

1 Desktop Board Features: a summary of product features

2 Installing and Replacing Desktop Board Components: instructions on how to install

the Desktop Board and other hardware components

3 Updating the BIOS: a description of how to update the BIOS

A BIOS Error Messages: information about BIOS error messages and beep codes

B Regulatory Compliance: safety and EMC regulations and product certifications

Conventions

The following conventions are used in this manual:

CAUTION

Cautions warn the user about how to prevent damage to hardware or loss of data.

NOTE

Notes call attention to important information.

Intel Desktop Board D510MO Product Guide

Terminology

The table below gives descriptions to some common terms used in the product guide.

Term Description

GB Gigabyte (1,073,741,824 bytes)

GHz Gigahertz (one billion hertz)

KB Kilobyte (1024 bytes)

MB Megabyte (1,048,576 bytes)

Mbit Megabit (1,048,576 bits)

MHz Megahertz (one million hertz)

Contents

1 Desktop Board Features

Desktop Board Components.................................................................................11

Processor..........................................................................................................13

System Memory.................................................................................................13

Integrated Graphics Subsystem ...........................................................................14

Intel

NM10 Express Chipset ...............................................................................14

Operating System Support ..................................................................................14

Onboard Audio Subsystem ..................................................................................14

Legacy Input/Output (I/O) Controller ....................................................................16

LAN Subsystem .................................................................................................16

USB 2.0 Support................................................................................................17

SATA Interface ..................................................................................................17

Expandability.....................................................................................................17

BIOS................................................................................................................18

PCI/PCI Express Auto Configuration ..............................................................18

Security Passwords.....................................................................................18

Power Management Features ...............................................................................19

ACPI.........................................................................................................19

Hardware Support ......................................................................................19

ENERGY STAR*, e-Standby, and ErP Compliance ....................................................22

Battery.............................................................................................................22

Real-Time Clock.................................................................................................22

2 Installing and Replacing Desktop Board Components

Before You Begin ...............................................................................................23

Installation Precautions.......................................................................................25

Prevent Power Supply Overload ....................................................................25

Observe Safety and Regulatory Requirements.................................................25

Installing the I/O Shield ......................................................................................26

Installing and Removing the Desktop Board ...........................................................27

Installing and Removing Memory..........................................................................27

Installing DIMMs ........................................................................................28

Removing DIMMs........................................................................................30

Connecting SATA Drives......................................................................................30

Installing a Wireless LAN Card in the PCI Express Full-Mini Card Slot .........................32

Installing an Intel

Z-U130 USB Solid-State Drive (or Compatible Device)..................33

Connecting to the Internal Headers ......................................................................34

Connecting the Front Panel Audio Header.......................................................35

Connecting to the S/PDIF Header..................................................................36

Connecting to the Serial Headers ..................................................................36

Connecting to the Parallel Port Header...........................................................36

Connecting to the Front Panel Wireless Activity LED Header..............................37

Connecting to the Front Panel Header............................................................38

Connecting to the Front Panel USB 2.0 Headers ..............................................38

Connecting a Chassis Fan....................................................................................39

Connecting the Power Supply Cable ......................................................................40

Intel Desktop Board D510MO Product Guide

Setting the BIOS Configuration Jumper .................................................................41

Clearing Passwords.....................................................................................42

Replacing the Battery .........................................................................................43

3 Updating the BIOS

Updating the BIOS with the Intel

Express BIOS Update Utility.................................49

Updating the BIOS with the Iflash Memory Update Utility.........................................50

Obtaining the BIOS Update File ....................................................................50

Using the Iflash Memory Update Utility ..........................................................50

Recovering the BIOS...................................................................................51

A Board Status and Error Message

BIOS Beep Codes...............................................................................................53

BIOS Front-panel Power LED Blink Codes ..............................................................54

POST Error Messages..........................................................................................54

B Regulatory Compliance

Safety Standards ...............................................................................................55

Place Battery Marking .................................................................................55

European Union Declaration of Conformity Statement..............................................56

Product Ecology Statements ................................................................................57

Recycling Considerations .............................................................................57

Lead-free 2LI/Pb-free 2LI Board ...................................................................60

Restriction of Hazardous Substances (RoHS) ..................................................61

EMC Regulations ................................................................................................63

Ensure Electromagnetic Compatibility (EMC) Compliance..................................64

Product Certifications..........................................................................................65

Board-Level Certification Markings ................................................................65

Chassis and Component Certifications............................................................66

Contents

vii

Figures

1. Intel Desktop Board D510MO Components .......................................................11

2. Back Panel Audio Connectors .........................................................................15

3. LAN Status LEDs ..........................................................................................16

4. Location of the Standby Power Indicator ..........................................................20

5. Installing the I/O Shield ................................................................................26

6. Intel Desktop Board D510MO Mounting Screw Holes..........................................27

7. Use DDR2 DIMMs .........................................................................................28

8. Installing a DIMM .........................................................................................29

9. Connecting the Serial ATA Cable .....................................................................31

10. Installing a Wireless LAN Card ........................................................................32

11. Installing an Intel Z-U130 USB Solid-State Drive (or Compatible Device)..............33

12. Internal Headers ..........................................................................................34

13. Location of the Chassis Fan Header .................................................................39

14. Connecting a Power Supply Cable ...................................................................40

15. BIOS Configuration Jumper Block....................................................................41

16. Removing the Battery ...................................................................................47

17. Intel Desktop Board D510MO China RoHS Material Self Declaration Table .............62

Tables

1. Feature Summary.......................................................................................... 9

2. Intel Desktop Board D510MO Components .......................................................12

3. Audio Jack Support .......................................................................................15

4. LAN Status LEDs ..........................................................................................17

5. ENERGY STAR Requirements ..........................................................................22

6. Front Panel Audio Header for Intel HD Audio.....................................................35

7. Front Panel Audio Header for AC ‘97 Audio .......................................................35

8. S/PDIF Header .............................................................................................36

9. Serial Port Headers (COM 1 and COM 2) ..........................................................36

10. Parallel Port Header ......................................................................................36

11. Front Panel Wireless Activity LED Header .........................................................37

12. Front Panel Header Signal Names ...................................................................38

13. Front Panel USB Header ................................................................................38

14. Front Panel USB Header with Intel Z-U130 USB Solid-State Drive

(or Compatible Device) Support......................................................................39

15. Jumper Settings for the BIOS Setup Program Modes..........................................42

16. AcceptableDrives/Media Types for BIOS Recovery .............................................51

17. BIOS Beep Codes .........................................................................................53

18. BIOS Front-panel Power LED Blink Codes.........................................................54

19. POST Error Messages ....................................................................................54

20. Safety Standards..........................................................................................55

21. Lead-Free Second Level Interconnect Marks .....................................................60

22. China RoHS Environmentally Friendly Use Period Mark.......................................61

23. EMC Regulations...........................................................................................63

24. Product Certification Markings ........................................................................65

Page is loading ...

1 Desktop Board Features

This chapter briefly describes the main features of Intel

Desktop Board D510MO.

Table 1 summarizes the features of the Desktop Board.

Table 1.

Feature Summary

Form Factor

Mini-ITX ([170 millimeters [6.7 inches] x 170 millimeters [6.7 inches])

Processor

Passively-cooled, soldered-down dual-core Intel

Atom

™

processor with

integrated graphics and memory controllers.

Main Memory

• Two 240-pin Double Data Rate 2 (DDR2) Dual Inline Memory Module

(DIMM) sockets with gold-plated contacts

• Support for DDR2 800 MHz and DDR2 667 MHz DIMMs

• Support for up to 4 GB total system memory (2 GB per DIMM

socket)

Chipset

Intel

NM10 Express Chipset

Integrated

Graphics

Intel

Graphics Media Accelerator 3150 (Intel

GMA 3150) integrated

graphics subsystem with support for analog displays (VGA)

Audio

RealTek* ALC662 audio codec for 5.1 (6-channel) Intel

High

Definition Audio (Intel

HD Audio) and AC ’97 Audio. Included are:

• Back panel connectors

• Front panel microphone/headphone header with support for

Intel

HD Audio or AC ’97 Audio

• S/PDIF digital audio header

Expansion

Capabilities

One PCI* bus add-in card connector

One PCI Express* Full-Mini Card slot

Peripheral

Interfaces

• Seven USB 2.0 ports:

― Four back panel ports

― Three front panel ports (via two internal headers; one header

supports an Intel

Z-U130 USB Solid-State Drive (or compatible

device)

• Two Serial ATA (SATA) 3.0 Gb/s connectors (supporting IDE and

ACHI)

Legacy I/O Control

Winbond* W83627TGH-I legacy I/O controller:

• Two serial port headers

• One parallel port header

• PS/2 keyboard and mouse connectors

Hardware Monitor

Subsystem

Hardware monitoring through the Winbond legacy I/O controller,

including:

• Remote thermal sensor

• One 3-pin chassis fan header with speed control

LAN Support

10/100/1000 Mb/s (Gigabit) Ethernet LAN Subsystem using a RealTek*

8111DL Gigabit Ethernet Controller

Intel Desktop Board D510MO Product Guide

BIOS

• Intel

BIOS

• Support for Advanced Configuration and Power Interface (ACPI),

Plug and Play, and SMBIOS

Instantly Available

PC Technology

• Support for PCI Local Bus Specification, Revision 2.3

• Support for Advanced Configuration and Power Interface (ACPI)

• Wake on USB, PCI, PCI Express, PS/2, LAN, serial, and front panel

For more information on Intel Desktop Board D510MO consult the following online

resources:

To find information

about…

Visit this World Wide Web site:

Intel Desktop Board

D510MO

http://www.intel.com/products/motherboard/D510MO/index.htm

Desktop Board Support http://support.intel.com/support/motherboards/desktop

Available configurations

for Intel Desktop Board

D510MO

http://www.intel.com/products/motherboard/D510MO/index.htm

Chipset information http://www.intel.com/products/desktop/chipsets/index.htm

BIOS and driver updates http://downloadcenter.intel.com/

Integration information http://www.intel.com/support/go/buildit

Desktop Board Features

Desktop Board Components

Figure 1 shows the location of the major components on Intel Desktop Board D510MO.

Figure 1. Intel Desktop Board D510MO Components

Intel Desktop Board D510MO Product Guide

Table 2. Intel Desktop Board D510MO Components

Label Description

A Back panel connectors

B Serial header (COM1)

C Parallel port header

D Serial port (COM 2)

E Chassis fan header

F Main power connector

G Standby power indicator

H Processor

I Channel A DIMM 0

J Channel A DIMM 1

K SATA 1

L SATA 0

M Front panel header

N Battery

O Front panel wireless activity LED header

P Intel NM10 Express Chipset

Q USB front panel header with Intel Z-U130 USB Solid-State Drive (or

compatible device) support

R PCI bus connector

S PCI Express Mini Card connector

T USB front panel header

U Front panel audio header

V BIOS configuration jumper block

W S/PDIF header

Desktop Board Features

Processor

Intel Desktop Board D510MO includes a passively-cooled, dual-core Intel Atom

processor with integrated graphics and memory controller. The processor is soldered

to the Desktop Board and is not customer upgradeable.

NOTE

The board is designed to be passively cooled in a properly ventilated chassis. Chassis

venting locations are recommended above the processor heatsink area for maximum

heat dissipation effectiveness.

System Memory

NOTE

To be fully compliant with all applicable Intel

SDRAM memory specifications, the

board should be populated with DIMMs that support the Serial Presence Detect (SPD)

data structure. If your memory modules do not support SPD, you will see a

notification to this effect on the screen at power up. The BIOS will attempt to

configure the memory controller for normal operation.

The Desktop Board has two 240-pin DDR2 DIMM connectors with gold-plated contacts.

It supports:

• DDR2 800 MHz or DDR2 667 MHz unbuffered, non-registered DIMMs

• Serial Presence Detect (SPD) memory only

• Non-ECC memory

• Up to 4 GB of memory

Intel Desktop Board D510MO Product Guide

Integrated Graphics Subsystem

The integrated Intel GMA 3150 graphics controller features the following:

• 400 MHz core frequency

• High quality texture engine

⎯ DX9.0c* and OpenGL* 1.4 compliant

⎯ Hardware Pixel Shader 2.0

⎯ Vertex Shader Model 2.0

• 3D Graphics Rendering enhancements

⎯ 1.6 dual texture GigaPixel/s max fill rate

⎯ 16-bit and 32-bit color

⎯ Vertex cache

• Video

⎯ Software DVD at 30 fps full screen

⎯ DVMT support up to 256 MB

• Supports analog displays up to 2048 x 1536 at 75 Hz refresh (QXGA)

Intel

NM10 Express Chipset

The Intel NM10 Express Chipset is a centralized controller for the board’s I/O paths.

For more information about the Intel NM10 Express Chipset, go to

http://www.intel.com/products/chipset

index.htm?iid=prod+prod_chipset.

Operating System Support

The following Microsoft* operating systems are fully supported by the Desktop Board:

• Microsoft Windows Vista* Home Basic, SP 1

• Microsoft Windows* XP Home, SP 3

• Microsoft Windows* 7 Home Basic and Starter

Onboard Audio Subsystem

The Intel Desktop Board D510MO 6-channel (5.1) onboard audio subsystem supports

both Intel HD Audio and AC ’97 Audio. The subsystem is based on the following

components:

• Intel NM10 Express Chipset

• RealTek ALC662 audio codec

The subsystem includes the following headers and connectors:

• Front panel audio header (supports both Intel HD Audio and AC ’97) , including

functionality for:

― Line out (headphones/speaker)

― Microphone in

• Three back panel analog audio jacks

• Onboard S/PDIF output header (3 pin)

Desktop Board Features

The front/back panel audio connectors are configurable through the audio device

drivers. Table 3 lists the supported functions

of the front panel and back panel jacks.

Table 3. Audio Jack Support

Audio Jack Line

Line/

Front Out

Rear Out Center/

LFE

Microphone Headphones

Front panel – Green No Yes No No No Yes

Front panel – Pink No No No No Yes No

Back panel – Blue Yes No Yes No No No

Back panel – Green No Yes No No No Yes

Back panel – Pink No No No Yes Yes No

Figure 2 shows the default assignment of the back panel audio connectors.

Item

Description

A Line In

B Line Out

C Mic In

Figure 2. Back Panel Audio Connectors

NOTE

The back panel audio line out connector is designed to power headphones or amplified

speakers only. Poor audio quality occurs if passive (non-amplified) speakers are

connected to this output.

Intel Desktop Board D510MO Product Guide

Legacy Input/Output (I/O) Controller

The legacy I/O controller provides the following:

• Two serial ports (via onboard headers)

• One parallel port with Extended Capabilities Port (ECP) and Enhanced Parallel Port

(EPP) support via an onboard headers

• Serial IRQ interface compatible with serialized IRQ support for PCI systems

• PS/2-style keyboard and mouse ports

• Intelligent power management, including a programmable wake up event interface

• PCI power management support

The BIOS Setup program provides configuration options for the legacy I/O controller.

LAN Subsystem

The LAN subsystem consists of the following:

• Intel NM10 Express Chipset

• Realtek 8111DL Gigabit Ethernet Controller for 10/100/1000 Mbits/s Ethernet LAN

connectivity

• RJ-45 LAN connector with integrated status LEDs

Additional features of the LAN subsystem include:

• CSMA/CD protocol engine

• LAN connect interface that supports the ethernet controller

• PCI bus power management

⎯ Supports ACPI technology

⎯ Supports LAN wake capabilities

LAN drivers are available from Intel’s World Wide Web site at

http://downloadcenter.intel.com/.

Two LEDs are built into the RJ-45 LAN connector located on the back panel (see

Figure 3). These LEDs indicate the operating states of the LAN.

Figure 3. LAN Status LEDs

Desktop Board Features

Table 4 describes the LED states when the board is powered up and the LAN

subsystem is operating.

Table 4. LAN Status LEDs

LED LED Color LED State Indicates

Activity (A) Green Blinking LAN activity is occurring.

N/A Off 10 Mbits/s data rate is selected.

Green On 100 Mbits/s data rate is selected.

Speed (B)

Yellow On 1000 Mbits/s data rate is selected.

USB 2.0 Support

The Desktop Board supports up to seven USB 2.0 ports (four ports routed to the back

panel and three ports routed to two front panel USB 2.0 headers). One of the front

panel USB headers supports an Intel Z-U130 USB Solid-State Drive (or compatible

device). The USB 2.0 ports are compatible with USB 1.1 devices. USB 1.1 devices will

function normally at USB 1.1 speeds.

USB 2.0 support requires both an operating system and drivers that fully support

USB 2.0 transfer rates. Disabling High-Speed USB in the BIOS reverts all USB 2.0

ports to USB 1.1 operation. This may be required to accommodate operating systems

that do not support USB 2.0.

NOTE

Computer systems that have an unshielded cable attached to a USB port might not

meet FCC Class B requirements, even if no device or a low-speed USB device is

attached to the cable. Use a shielded cable that meets the requirements for a

full-speed USB device.

SATA Interface

The Desktop Board supports two SATA channels (3.0 Gb/s) that support one device

per channel. The SATA controller supports IDE and ACHI configuration and can

operate in both legacy and native modes.

Expandability

The Desktop Board provides the following expansion capability:

• One PCI connector. The connector can support either a single PCI add-in card or a

single- or dual-slot PCI riser card.

• One PCI Express Full-Mini Card slot.

Intel Desktop Board D510MO Product Guide

BIOS

The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI

and IDE auto-configuration utilities, and the video BIOS.

PCI/PCI Express Auto Configuration

If you install a PCI/PCI Express add-in card in your computer, the PCI/PCI Express

auto-configuration utility in the BIOS automatically detects and configures the

resources (IRQs, DMA channels, and I/O space) for that add-in card. You do not need

to run the BIOS Setup program after you install a PCI/PCI Express add-in card.

Security Passwords

The BIOS includes security features that restrict whether the BIOS Setup program can

be accessed and who can boot the computer. A supervisor password and a user

password can be set for the BIOS Setup and for booting the computer, with the

following restrictions:

• The supervisor password gives unrestricted access to view and change all Setup

options. If only the supervisor password is set, pressing <Enter> at the password

prompt of Setup gives the user restricted access to Setup.

• If both the supervisor and user passwords are set, you must enter either the

supervisor password or the user password to access Setup. Setup options are then

available for viewing and changing depending on whether the supervisor or user

password was entered.

• Setting a user password restricts who can boot the computer. The password

prompt is displayed before the computer is booted. If only the supervisor

password is set, the computer boots without asking for a password. If both

passwords are set, you can enter either password to boot the computer.

For instructions on resetting the password, see Clearing Passwords on page 42.

Desktop Board Features

Power Management Features

Power management is implemented at several levels, including:

• Software support through the Advanced Configuration and Power Interface (ACPI)

• Hardware support:

― Power connector

― Fan header

― +5 V standby power indicator LED

― LAN Wake capabilities

― Instantly Available PC technology

― Wake from USB

― Wake from PS/2 devices

― PME# wakeup support

― WAKE# signal wakeup support

― Wake from serial port

ACPI

ACPI gives the operating system direct control over the power management and Plug

and Play functions of a computer. The use of ACPI with the Desktop Board requires an

operating system that provides full ACPI support.

Hardware Support

Fan Header

The Desktop Board has a 3-pin chassis fan header. See Figure 13 on page 39 for the

location of the chassis fan header.

+5 V Standby Power Indicator

CAUTION

If the AC power has been switched off and the standby power indicator is still lit,

disconnect the power cord before installing or removing any devices connected to the

board. Failure to do so could damage the board and any attached devices.

The Desktop Board’s standby power indicator, shown in Figure 4, is lit when there is

standby power to the system. This includes the DIMM socket and the PCI bus

connector, even though the computer appears to be off.

Intel Desktop Board D510MO Product Guide

Figure 4. Location of the Standby Power Indicator

For more information on standby current requirements for the Desktop Board, refer to

the Technical Product Specification on the Intel Desktop D510MO web page at

http://www.intel.com/products/motherboard/D510MO/index.htm.

Instantly Available PC Technology

Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to-

RAM) sleep-state. While in the ACPI S3 sleep-state, the computer will appear to be off

(the hard drive(s) and fan will power off, the front panel power LED will blink). When

signaled by a wake-up device or event, the system quickly returns to its last known

state.

The board supports the PCI Bus Power Management Interface Specification. Add-in

boards that also support this specification can participate in power management and

can be used to wake the computer.

The use of Instantly Available PC technology requires operating system support and

PCI 2.3 compliant add-in cards and drivers.

Desktop Board Features

LAN Wake Capabilities

The board’s LAN wake capabilities enable remote wake-up of the computer through a

network. The LAN subsystem network adapter monitors network traffic at the Media

Independent Interface. The board supports LAN wake capabilities with ACPI in the

following ways:

• By Ping

• By Magic Packet

Upon detecting the configured wake packet type, the LAN subsystem asserts a wake-

up signal that powers up the computer.

Wake from USB

USB bus activity wakes the computer from an ACPI S1 or S3 state.

NOTE

Wake from USB requires the use of a USB peripheral that supports wake from USB.

Wake from PS/2 Device

PS/2 keyboard activity wakes the computer from an ACPI S1, S3, S4, or S5 state.

However, when the computer is in an ACPI S4 or S5 state, the only PS/2 activity that

will wake the computer is the Alt + Print Screen key combination or the Power key

available only on some keyboards.

PME# Wakeup Support

When the PME# signal is asserted on the PCI bus, the computer wakes from an ACPI

S1, S3, S4, or S5 state.

WAKE# Signal Wakeup Support

When the WAKE# signal is asserted on the PCI Express bus, the computer wakes from

an ACPI S1, S3, S4, or S5 state.

Wake from Serial Port

Serial port activity wakes the computer from an ACPI S1 or S3 state.

Intel Desktop Board D510MO Product Guide

ENERGY STAR*, e-Standby, and ErP

Compliance

Intel Desktop Board D510MO meets the ENERGY STAR requirements listed in Table 5

when used in corresponding system configurations.

Table 5. ENERGY STAR Requirements

ENERGY STAR

Specification

Computer Type

Required

States

Capability

Adjustments

Typical

Electricity

Consumption

(TEC) Criteria

v4.0 Desktop Computer

v4.0 Integrated

Computer

Idle State

(Cat A)

Sleep Mode

Standby Level

With and

without Wake

On LAN (Sleep,

Standby)

N/A

v5.0 Desktop Computer

v5.0 Integrated Desktop

Computer

Off Mode

Sleep Mode

Idle State

Active State

With and

without

additional

internal storage

Cat A under

“desktop

conventional”

and “desktop

proxying”

operational

mode

weightings

v5.0 Thin Client Off Mode

Sleep Mode

Idle State

(Cat B)

With and

without Wake

On LAN (Sleep,

Standby)

N/A

For information about ENERGY STAR requirements and recommended configurations,

go to http://www.intel.com/go/energystar

The Desktop Board also meets the following international requirements:

• Republic of Korea e-Standby program

• European Union Energy using Products (EuP) directive

Battery

A coin-cell battery on the Desktop Board keeps the values in CMOS RAM and the clock

current when the computer is turned off. Go to page 43 for instructions on how to

replace the battery.

Real-Time Clock

The Desktop Board includes a time-of-day clock and a 100-year calendar. The coin-

cell battery keeps the clock current when the computer is turned off.

Page is loading ...

Intel D510MO User manual

Brand: Intel

Model: D510MO

Category: Motherboards

Type: User manual

Download PDF

report

Intel D510MO User manual

Intel D510MO User manual

Related papers

Other documents