Intel BOXD410PT User manual

Category
Motherboards
Type
User manual

This manual is also suitable for

Intel® Desktop Board D410PT
Product Guide
Order Number: E74522-002
Revision History
Revision Revision History Date
-001 First release of the Intel
®
Desktop Board D410PT Product Guide October 2009
-002 Second release of the Intel
®
Desktop Board D410PT Product
Guide
December 2009
If an FCC declaration of conformity marking is present on the board, the following statement applies:
FCC Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
For questions related to the EMC performance of this product, contact:
Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124,
1-800-628-8686
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the
user’s authority to operate the equipment.
Tested to comply with FCC standards for home or office use.
Canadian Department of Communications Compliance Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set
out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par
le ministére des Communications du Canada.
Disclaimer
Information in this document is provided in connection with Intel
®
products. No license, express or implied,
by estoppel or
otherwise, to any intellectual property rights is granted by this document. Except as provided
in Intel’s Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel
disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or
warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent,
copyright or other intellectual property right. Intel products are not intended for use in medical, life saving,
or life sustaining applications. Intel may make changes to specifications and product descriptions at any
time, without notice.
Intel Desktop Board D410PT may contain design defects or errors known as errata which may cause the
product to deviate from published specifications. Current characterized errata are available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing
your product order.
Copies of documents which have an ordering number and are referenced in this document, or other Intel
literature, may be obtained from Intel Corporation by going to the World Wide Web site at:
http://www.intel.com/ or by calling 1-800-548-4725.
Intel, the Intel logo, and Intel Atom are trademarks of Intel Corporation in the U. S. and other countries.
* Other names and brands may be claimed as the property of others.
Copyright © 2009 Intel Corporation. All rights reserved.
iii
Preface
This Product Guide gives information about board layout, component installation, and
regulatory requirements for Intel
®
Desktop Board D410PT.
Intended Audience
The Product Guide is intended for technically qualified personnel. It is not intended for
general audiences.
Intended Uses
All Intel
®
Desktop Boards are evaluated as Information Technology Equipment (I.T.E.)
for use in personal computers (PC) for installation in homes, offices, schools, computer
rooms, and similar locations. The suitability of this product for other PC or embedded
non-PC applications or other environments, such as medical, industrial, alarm systems,
test equipment, etc. may not be supported without further evaluation by Intel.
Document Organization
The chapters in this Product Guide are arranged as follows:
1 Desktop Board Features: a summary of product features
2 Installing and Replacing Desktop Board Components: instructions on how to install
the Desktop Board and other hardware components
3 Updating the BIOS: a description of how to update the BIOS
A BIOS Error Messages: information about BIOS error messages and beep codes
B Regulatory Compliance: safety and EMC regulations and product certifications
Conventions
The following conventions are used in this manual:
CAUTION
Cautions warn the user about how to prevent damage to hardware or loss of data.
NOTE
Notes call attention to important information.
Intel Desktop Board D410PT Product Guide
iv
Terminology
The table below gives descriptions to some common terms used in the product guide.
Term Description
GB Gigabyte (1,073,741,824 bytes)
GHz Gigahertz (one billion hertz)
KB Kilobyte (1024 bytes)
MB Megabyte (1,048,576 bytes)
Mbit Megabit (1,048,576 bits)
MHz Megahertz (one million hertz)
v
Contents
1 Desktop Board Features
Desktop Board Components.................................................................................11
Processor..........................................................................................................13
System Memory.................................................................................................13
Integrated Graphics Subsystem ...........................................................................14
Intel
®
NM10 Express Chipset ...............................................................................14
Operating System Support ..................................................................................14
Onboard Audio Subsystem ..................................................................................14
Legacy Input/Output (I/O) Controller ....................................................................16
LAN Subsystem .................................................................................................16
USB 2.0 Support................................................................................................17
SATA Interface ..................................................................................................17
Expandability.....................................................................................................17
BIOS................................................................................................................18
PCI Auto Configuration ................................................................................18
Security Passwords.....................................................................................18
Power Management Features ...............................................................................18
ACPI.........................................................................................................19
Hardware Support ......................................................................................19
ENERGY STAR*, e-Standby, and ErP Compliance ....................................................22
Battery.............................................................................................................22
Real-Time Clock.................................................................................................22
2 Installing and Replacing Desktop Board Components
Before You Begin ...............................................................................................23
Installation Precautions.......................................................................................25
Prevent Power Supply Overload ....................................................................25
Observe Safety and Regulatory Requirements.................................................25
Installing the I/O Shield ......................................................................................26
Installing and Removing the Desktop Board ...........................................................27
Installing and Removing Memory..........................................................................27
Installing DIMMs ........................................................................................28
Removing DIMMs........................................................................................30
Connecting SATA Drives......................................................................................30
Connecting to the Internal Headers ......................................................................32
Connecting the Front Panel Audio Header.......................................................33
Connecting to the Serial Headers ..................................................................34
Connecting to the Front Panel Header............................................................34
Connecting to the Front Panel USB 2.0 Headers ..............................................35
Connecting a Chassis Fan....................................................................................35
Connecting the Power Supply Cable ......................................................................36
Setting the BIOS Configuration Jumper .................................................................37
Clearing Passwords.....................................................................................38
Replacing the Battery .........................................................................................39
Intel Desktop Board D410PT Product Guide
vi
3 Updating the BIOS
Updating the BIOS with the Intel
®
Express BIOS Update Utility.................................45
Updating the BIOS with the Iflash Memory Update Utility.........................................46
Obtaining the BIOS Update File ....................................................................46
Using the Iflash Memory Update Utility ..........................................................46
Recovering the BIOS...................................................................................47
A Board Status and Error Messages
BIOS Beep Codes...............................................................................................49
BIOS Front-panel Power LED Blink Codes ..............................................................50
POST Error Messages..........................................................................................50
B Regulatory Compliance
Safety Standards ...............................................................................................51
Place Battery Marking .................................................................................51
European Union Declaration of Conformity Statement..............................................52
Product Ecology Statements ................................................................................53
Recycling Considerations .............................................................................53
Lead-free 2LI/Pb-free 2LI Board ...................................................................56
Restriction of Hazardous Substances (RoHS) ..................................................57
EMC Regulations ................................................................................................59
Ensure Electromagnetic Compatibility (EMC) Compliance..................................60
Product Certifications..........................................................................................61
Board-Level Certification Markings ................................................................61
Chassis and Component Certifications............................................................62
Contents
vii
Figures
1. Intel Desktop Board D410PT Components ........................................................11
2. Back Panel Audio Connectors .........................................................................15
3. LAN Status LEDs ..........................................................................................16
4. Location of the Standby Power Indicator ..........................................................20
5. Installing the I/O Shield ................................................................................26
6. Intel Desktop Board D410PT Mounting Screw Holes...........................................27
7. Use DDR2 DIMMs .........................................................................................28
8. Installing a DIMM .........................................................................................29
9. Connecting a Serial ATA Cable........................................................................31
10. Internal Headers ..........................................................................................32
11. Location of the Chassis Fan Header .................................................................35
12. Connecting a Power Supply Cable ...................................................................36
13. BIOS Configuration Jumper Block....................................................................37
14. Removing the Battery ...................................................................................43
15. Intel Desktop Board D410PT China RoHS Material Self Declaration Table ..............58
Tables
1. Feature Summary.......................................................................................... 9
2. Intel Desktop Board D410PT Components ........................................................12
3. Audio Jack Support .......................................................................................15
4. LAN Status LEDs ..........................................................................................17
5. ENERGY STAR Requirements ..........................................................................22
6. Front Panel Audio Header for Intel HD Audio.....................................................33
7. Front Panel Audio Header for AC ‘97 Audio .......................................................33
8. Serial Port Headers (COM 1 and COM 2) ..........................................................34
9. Front Panel Header Signal Names ...................................................................34
10. Front Panel USB Header ................................................................................35
11. Jumper Settings for the BIOS Setup Program Modes..........................................38
12. Acceptable Drives/Media Types for BIOS Recovery ............................................47
13. BIOS Beep Codes .........................................................................................49
14. BIOS Front-panel Power LED Blink Codes.........................................................50
15. POST Error Messages ....................................................................................50
16. Safety Standards..........................................................................................51
17. Lead-Free Second Level Interconnect Marks .....................................................56
18. China RoHS Environmentally Friendly Use Period Mark.......................................57
19. EMC Regulations...........................................................................................59
20. Product Certification Markings ........................................................................61
Intel Desktop Board D410PT Product Guide
viii
9
1 Desktop Board Features
This chapter briefly describes the main features of Intel
®
Desktop Board D410PT.
Table 1 summarizes the features of the Desktop Board.
Table 1.
Feature Summary
Form Factor
Mini-ITX ([170 millimeters [6.7 inches] x 170 millimeters [6.7 inches])
Processor
Passively-cooled, soldered-down single-core Intel
®
Atom
processor
with integrated graphics and memory controllers.
Main Memory
Two 240-pin Double Data Rate 2 (DDR2) Dual Inline Memory Module
(DIMM) sockets with gold-plated contacts
Support for DDR2 800 MHz and DDR2 667 MHz DIMMs
Support for up to 4 GB total system memory (2 GB per DIMM
socket)
Chipset
Intel
®
NM10 Express Chipset
Integrated
Graphics
Intel
®
Graphics Media Accelerator 3150 (Intel
®
GMA 3150) integrated
graphics subsystem with support for analog displays (VGA)
Audio
Realtek* ALC662 audio codec for 4-channel Intel
®
High Definition
Audio (Intel
®
HD Audio) and AC ’97 Audio. Included are:
Back panel connectors
Front panel microphone/headphone header with support for
Intel
®
HD Audio or AC ’97 Audio
Expansion
Capabilities
One PCI* bus add-in card connector
Peripheral
Interfaces
Eight USB 2.0 ports:
Four back panel ports
Four front panel ports via two internal headers
Two Serial ATA (SATA) 3.0 Gb/s connectors (supporting IDE and
ACHI)
Legacy I/O Control
Winbond* W83627TGH-I legacy I/O controller:
Two serial port headers
PS/2 keyboard and mouse connectors
Hardware Monitor
Subsystem
Hardware monitoring through the Winbond legacy I/O controller,
including:
Remote thermal sensor
One 3-pin chassis fan header with speed control
LAN Support
10/100 Mb/s Ethernet LAN Subsystem using a Realtek RTL8103EL
Ethernet Controller
BIOS
Intel
®
BIOS
Support for Advanced Configuration and Power Interface (ACPI),
Plug and Play, and SMBIOS
Instantly Available
PC Technology
Support for PCI Local Bus Specification, Revision 2.3
Support for Advanced Configuration and Power Interface (ACPI)
Wake on USB, PCI, PS/2, LAN, serial, and front panel
Intel Desktop Board D410PT Product Guide
10
For more information on Intel Desktop Board D410PT consult the following online
resources:
To find information
about…
Visit this World Wide Web site:
Intel Desktop Board
D410PT
http://www.intel.com/products/motherboard/D410PT/index.htm
Desktop Board Support http://support.intel.com/support/motherboards/desktop
Available configurations
for Intel Desktop Board
D410PT
http://www.intel.com/products/motherboard/D410PT/index.htm
Chipset information http://www.intel.com/products/desktop/chipsets/index.htm
BIOS and driver updates http://downloadcenter.intel.com/
Integration information http://www.intel.com/support/go/buildit
Desktop Board Features
11
Desktop Board Components
Figure 1 shows the location of the major components on Intel Desktop Board D410PT.
Figure 1. Intel Desktop Board D410PT Components
Intel Desktop Board D410PT Product Guide
12
Table 2. Intel Desktop Board D410PT Components
Label Description
A Back panel connectors
B Serial header (COM1)
C Serial port (COM 2)
D Chassis fan header
E Main power connector
F Standby power indicator
G Processor
H Channel A DIMM 0
I Channel A DIMM 1
J SATA 1
K SATA 0
L Front panel header
M Battery
N Intel NM10 Express Chipset
O USB front panel header
P PCI bus connector
Q USB front panel header
R Front panel audio header
S BIOS configuration jumper block
Desktop Board Features
13
Processor
Intel Desktop Board D410PT includes a passively-cooled, single-core Intel Atom
processor with integrated graphics and memory controller. The processor is soldered
to the Desktop Board and is not customer upgradeable.
NOTE
The board is designed to be passively cooled in a properly ventilated chassis. Chassis
venting locations are recommended above the processor heatsink area for maximum
heat dissipation effectiveness.
System Memory
NOTE
To be fully compliant with all applicable Intel
®
SDRAM memory specifications, the
board should be populated with DIMMs that support the Serial Presence Detect (SPD)
data structure. If your memory modules do not support SPD, you will see a
notification to this effect on the screen at power up. The BIOS will attempt to
configure the memory controller for normal operation.
The Desktop Board has two 240-pin DDR2 DIMM connectors with gold-plated contacts.
It supports:
DDR2 800 MHz or DDR2 667 MHz unbuffered, non-registered DIMMs
Serial Presence Detect (SPD) memory only
Non-ECC memory
Up to 4 GB of memory
Intel Desktop Board D410PT Product Guide
14
Integrated Graphics Subsystem
The integrated Intel GMA 3150 graphics controller features the following:
400 MHz core frequency
High quality texture engine
DX9.0c* and OpenGL* 1.4 compliant
Hardware Pixel Shader 2.0
Vertex Shader Model 2.0
3D Graphics Rendering enhancements
1.6 dual texture GigaPixel/s max fill rate
16-bit and 32-bit color
Vertex cache
Video
Software DVD at 30 fps full screen
DVMT support up to 256 MB
Supports analog displays up to 2048 x 1536 at 75 Hz refresh (QXGA)
Intel
®
NM10 Express Chipset
The Intel NM10 Express Chipset is a centralized controller for the board’s I/O paths.
For more information about the Intel NM10 Express Chipset, go to
http://www.intel.com/products/chipset
s/
index.htm?iid=prod+prod_chipset.
Operating System Support
The following Microsoft* operating systems are fully supported by the Desktop Board:
Microsoft Windows Vista* Home Basic, SP 1
Microsoft Windows* XP Home, SP 3
Microsoft Windows* 7 Home Basic and Starter
Onboard Audio Subsystem
The Intel Desktop Board D410PT 4-channel onboard audio subsystem supports both
Intel HD Audio and AC ’97 Audio. The subsystem is based on the following
components:
Intel NM10 Express Chipset
Realtek ALC662 audio codec
The subsystem includes the following headers and connectors:
Front panel audio header (supports both Intel HD Audio and AC ’97) , including
functionality for:
Line out (headphones/speaker)
Microphone in
Three back panel analog audio jacks
Desktop Board Features
15
The front/back panel audio connectors are configurable through the audio device
drivers. Table 3 lists the supported functions
of the front panel and back panel jacks.
Table 3. Audio Jack Support
Audio Jack
Line
In
Line/
Front Out
Rear Out
Microphone
Headphones
Front panel – Green No Yes No No Yes
Front panel – Pink No No No Yes No
Back panel – Blue Yes No Yes No No
Back panel – Green No Yes No No Yes
Back panel – Pink No No No Yes No
Figure 2 shows the default assignment of the back panel audio connectors.
Item
Description
A Line In
B Line Out
C Mic In
Figure 2. Back Panel Audio Connectors
NOTE
The back panel audio line out connector is designed to power headphones or amplified
speakers only. Poor audio quality occurs if passive (non-amplified) speakers are
connected to this output.
Intel Desktop Board D410PT Product Guide
16
Legacy Input/Output (I/O) Controller
The legacy I/O controller provides the following:
Two serial ports (via onboard headers)
Serial IRQ interface compatible with serialized IRQ support for PCI systems
PS/2-style keyboard and mouse ports
Intelligent power management, including a programmable wake up event interface
PCI power management support
The BIOS Setup program provides configuration options for the legacy I/O controller.
LAN Subsystem
The LAN subsystem consists of the following:
Intel NM10 Express Chipset
Realtek RTL8103EL Ethernet Controller for 10/100 Mbits/s Ethernet LAN
connectivity
RJ-45 LAN connector with integrated status LEDs
Additional features of the LAN subsystem include:
CSMA/CD protocol engine
LAN connect interface that supports the ethernet controller
PCI bus power management
Supports ACPI technology
Supports LAN wake capabilities
LAN drivers are available from Intel’s World Wide Web site at
http://downloadcenter.intel.com/.
Two LEDs are built into the RJ-45 LAN connector located on the back panel (see
Figure 3). These LEDs indicate the operating states of the LAN.
Figure 3. LAN Status LEDs
Desktop Board Features
17
Table 4 describes the LED states when the board is powered up and the LAN
subsystem is operating.
Table 4. LAN Status LEDs
LED LED Color LED State Indicates
Activity (A) Green Blinking LAN activity is occurring.
N/A Off 10 Mbits/s data rate is selected.
Speed (B)
Yellow On 100 Mbits/s data rate is selected.
USB 2.0 Support
The Desktop Board supports up to eight USB 2.0 ports (four ports routed to the back
panel and four ports routed to two front panel USB 2.0 headers). The USB 2.0 ports
are compatible with USB 1.1 devices. USB 1.1 devices will function normally at
USB 1.1 speeds.
USB 2.0 support requires both an operating system and drivers that fully support
USB 2.0 transfer rates. Disabling High-Speed USB in the BIOS reverts all USB 2.0
ports to USB 1.1 operation. This may be required to accommodate operating systems
that do not support USB 2.0.
NOTE
Computer systems that have an unshielded cable attached to a USB port might not
meet FCC Class B requirements, even if no device or a low-speed USB device is
attached to the cable. Use a shielded cable that meets the requirements for a
full-speed USB device.
SATA Interface
The Desktop Board supports two SATA channels (3.0 Gb/s) that support one device
per channel. The SATA controller supports IDE and ACHI configuration and can
operate in both legacy and native modes.
Expandability
For system expansion, the Desktop Board provides one PCI connector that can support
either a single PCI add-in card or a single- or dual-slot PCI riser card.
Intel Desktop Board D410PT Product Guide
18
BIOS
The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI
and IDE auto-configuration utilities, and the video BIOS.
PCI Auto Configuration
If you install a PCI add-in card in your computer, the PCI auto-configuration utility in
the BIOS automatically detects and configures the resources (IRQs, DMA channels,
and I/O space) for that add-in card. You do not need to run the BIOS Setup program
after you install a PCI add-in card.
Security Passwords
The BIOS includes security features that restrict whether the BIOS Setup program can
be accessed and who can boot the computer. A supervisor password and a user
password can be set for the BIOS Setup and for booting the computer, with the
following restrictions:
The supervisor password gives unrestricted access to view and change all Setup
options. If only the supervisor password is set, pressing <Enter> at the password
prompt of Setup gives the user restricted access to Setup.
If both the supervisor and user passwords are set, you must enter either the
supervisor password or the user password to access Setup. Setup options are then
available for viewing and changing depending on whether the supervisor or user
password was entered.
Setting a user password restricts who can boot the computer. The password
prompt is displayed before the computer is booted. If only the supervisor
password is set, the computer boots without asking for a password. If both
passwords are set, you can enter either password to boot the computer.
For instructions on resetting the password, see Clearing Passwords on page 38.
Power Management Features
Power management is implemented at several levels, including:
Software support through the Advanced Configuration and Power Interface (ACPI)
Hardware support:
Power connector
Fan header
+5 V standby power indicator LED
LAN Wake capabilities
Instantly Available PC technology
Wake from USB
Wake from PS/2 devices
PME# wakeup support
Wake from serial port
Desktop Board Features
19
ACPI
ACPI gives the operating system direct control over the power management and Plug
and Play functions of a computer. The use of ACPI with the Desktop Board requires an
operating system that provides full ACPI support.
Hardware Support
Fan Header
The Desktop Board has a 3-pin chassis fan header. See Figure 11 on page 35 for the
location of the chassis fan header.
+5 V Standby Power Indicator
CAUTION
If the AC power has been switched off and the standby power indicator is still lit,
disconnect the power cord before installing or removing any devices connected to the
board. Failure to do so could damage the board and any attached devices.
The Desktop Board’s standby power indicator, shown in Figure 4, is lit when there is
standby power to the system. This includes the DIMM socket and the PCI bus
connector, even though the computer appears to be off.
Intel Desktop Board D410PT Product Guide
20
Figure 4. Location of the Standby Power Indicator
For more information on standby current requirements for the Desktop Board, refer to
the Technical Product Specification on the Intel Desktop D410PT web page at
http://www.intel.com/products/motherboard/D410PT/index.htm.
Instantly Available PC Technology
Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to-
RAM) sleep-state. While in the ACPI S3 sleep-state, the computer will appear to be off
(the hard drive(s) and fan will power off, the front panel power LED will blink). When
signaled by a wake-up device or event, the system quickly returns to its last known
state.
The board supports the PCI Bus Power Management Interface Specification. Add-in
boards that also support this specification can participate in power management and
can be used to wake the computer.
The use of Instantly Available PC technology requires operating system support and
PCI 2.3 compliant add-in cards and drivers.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62

Intel BOXD410PT User manual

Category
Motherboards
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages