Vivo STAND-V103 Assembly Instructions

Brand: Vivo

Model: STAND-V103

Category: Flat panel desk mounts

Type: Assembly Instructions

Triple Monitor Desk Mount

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v103

SKU: STAND-V103

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

WARNING!

a (x1)

48mm pipe

b1 (x1)

“C” Clamp

b2 (x1)

“C” Clamp Brace

i (x2)

M10x15

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no

missing or defective parts. Improper installation may cause damage or serious injury. Do not

use this product for any purpose that is not explicitly specified in this manual. Do not exceed

weight capacity. We cannot be liable for damage or injury caused by improper mounting,

incorrect assembly or inappropriate use.

c (x1)

Decorative

Cover

d1 (x1)

Monitor Arm

e (x4)

Monitor Arm

Cover

f (x4)

Plastic Pad

g (x2)

M10x47

h (x3)

M6x8

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

j (x2)

M8x10

n (x1)

Spring Washer

k (x1)

M10 Bolt

l (x1)

Support

m (x1)

M10

o (x1)

EVA Pad

s (x2)

Spare Cap

p (x12)

M4x12

q (x12)

M4x30

r (x12)

M4 Spacer

t (x1)

Allen Key Set

w1 (x2)

Nut

u (x1)

Wrench

v1 (x2)

Side VESA

Plate

v2 (x1)

Center

VESA Plate

w2 (x1)

M4x6 Bolt

x (x4)

Wire Clip

d2 (x2)

Monitor Arm

ASSEMBLY STEPS

STEP 1

OPTION A: “C” Clamp Installation

Install the C-clamp Brace (b2) to the 48mm Pipe (a) using 3pcs C-clamp Brace

Bolts (h). Install the C-clamp (b1) to the 48mm Pipe (a) assembly according to the

thickness of the desktop. The thickness can be changed in three positions. Connect

it using 2pcs M10x15 Bolts (i), and tighten using the Allen Wrench (t). Tighten the

C-clamp to the desktop using the 2pcs eye bolts. Install the Decorative Cover (c).

TOOLS NEEDED

Phillips

Screwdriver

OPTION B: Existing Grommet Base Installation

If the existing grommet hole comes with a plastic

protector, remove it to ensure a flat surface before

installing the desk mount. Stick the EVA Pad (o) on the

round surface of 48mm Pipe (a). Position the 48mm

Pipe (a) on the mounting surface and secure using

the Support Plate (l), M10 Washer (m), Spring Washer

(n) and M10 Bolt (k). Fasten the M10 Bolt by provided

Wrench (u). Install the Decorative Cover (c).

Drill

22 lbs

Per Arm

(10 kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

Eye Bolt

STEP 1 (Continued)

STEP 2

Place plastic pads (f) on top and bottom of monitor arms (d2), making sure pins

are inserted into holes on arm. Position on ends of monitor arms (d1), secure with

M10x47 bolts (g), then press monitor arm covers (e) in place.

OPTION C: Self-Drilled Grommet Base Installation

Position the 48mm Pipe (a) on the mounting surface and mark the center hole.

Remove the tube support. Drill a 3/8” (10mm) diameter hole at the marked

position through the mounting surface. Stick the EVA Pad (o) on the round surface

of 48mm Pipe (a). Position the 48mm Pipe (a) on the mounting surface and secure

using the Support Plate (l), M10 Washer (m), Spring Washer (n) and M10 Bolt (k).

Fasten the M10 Bolt by provided Wrench (u). Install the Decorative Cover (c).

ÇO

ÇN

STEP 3

Install Monitor Arm (d1,d2) to the 48mm Pipe (a), please make sure the wire clips

(x) of Monitor Arm (d1,d2) in the downside. Fasten the M8x10 Bolt (j) by supplier

Allen key (t).

ÇNI ÇO

d1. d2

STEP 4

OPTION A: Flat Back Monitor

Attach side VESA plates (v1) to monitors

using M4x12 screws (p).

OPTION B: Curved Back Monitor

Attach side VESA plates (v1) to monitors

using M4x30 screws (q) and M4 spacers

Attach center VESA plate (v2) to

monitors using M4x12 screws (p).

Attach center VESA plate (v2) to

monitors using M4x30 screws (q) and

M4 spacers (r).

î N

î O

STEP 6

Pry o the plastic cover and then use

the Wrench (u) to tighten the nut if the

tilt angle can not be fixed.

Fix the tilt angle

Fasten the grub screw in monitor arm

to fix the tilting angle by provided

Allen key (t).

grub

screw

Fix the tilt angle

Slide the side monitors onto the head

of Swivel Arm (d1,d2) as shown in the

diagram. Install the security nut (w1).

Make sure the security nut is installed

before you rotate the monitor.

STEP 5

Slide the center monitor onto the head

of Monitor Arm (d1,d2) as shown in the

diagram. Install the M4x6 Bolt (w2).

Make sure the bolt is installed before

you rotate the monitor.

ÇNI ÇO

d1. d2

ÇNI ÇO

d1. d2

ï O

ï N

STEP 7

Adjust the Height of Center Monitor:

Turn the bolt counterclockwise to

lower the center monitor, turn the bolt

clockwise to raise the center monitor.

Adjust the Height of Side Monitors:

Remove the nut (w1) and turn the bolt

counter-clockwise with supplied Allen

key (t) to raise the monitor. Install nut

(w1) aer adjustment.

STEP 9

Manage the wires.

STEP 8

Pry o the arm cover, then use the Allen key (t) to

adjust the swivel joint tension.

LAST UPDATED: 06/10/2020

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected]

AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Vivo STAND-V103 Assembly Instructions

Brand: Vivo

Model: STAND-V103

Category: Flat panel desk mounts

Type: Assembly Instructions

Download PDF

report

in other languages

italiano: Vivo STAND-V103

Vivo STAND-V103 Assembly Instructions

Vivo STAND-V103 Assembly Instructions

in other languages

Related papers

Other documents