Vivo STAND-V003FG Assembly Instructions

Brand: Vivo

Model: STAND-V003FG

Type: Assembly Instructions

Triple Monitor Desk Stand

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v003fg

SKU: STAND-V003FG

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

a (x1)

Pole

b (x1)

Glass Base

c (x1)

Arm

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

d (x1)

Decorative

Cover

e (x3)

M6x10

f (x3)

Connecting

Bolt

g (x3)

M8 Washer

h (x2)

M8x10

i (x4)

Rubber Feet

j (x1)

So Pad

k (x1)

Allen Key

l (x1)

Wrench

m (x12)

M4x12

n (x12)

M4x30

o (x12)

M4 Spacer

p (x2)

Spare Plastic

Cover

q (x2)

VESA Plate

(side)

r (x1)

VESA Plate

(center)

s (x2)

Security Nut

t (x1)

M4x6 Bolt

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD

OR BACKWARD.

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

Weighted Base Installation

Attach Rubber Feet (i) to the underside of the Glass Base (b).

Attach So Pad (j) to the Pole (a). Use a screwdriver to poke

holes for screws through the pad. Install Pole to Glass Base

using M6x10 Bolts (e), Connecting Bolts (f) and M8 Washers (g),

and tighten with medium Allen Key (k) and screwdriver. Slide

Decorative Cover (d) over the Pole.

ASSEMBLY STEPS

STEP 1

Figure 4

22 lbs

(10 kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

PER ARM

TOOLS NEEDED

Phillips

Screwdriver

STEP 2

Install Arm (c) to the Pole (a). Secure using M8x10 Bolts (h) with a Phillips screwdriver.

STEP 3

OPTION A: Flat Back Monitor

Fasten the VESA Plates (q, r) to monitors using M4x12 Thumbscrews (m). Do not overtighten;

Thumbscrews only need to be finger-tight.

OPTION B: Curved Back Monitor

Fasten the VESA Plates (q, r) to monitors using M4x30 Screws (n) and spacers (o).

STEP 4

Slide the center monitor onto the center head of Monitor Arm (c). Install the M4x6 bolt (t) to secure the

monitor. Slide the side monitors onto the heads of Monitor Arm (c). Install the Security Nuts (s).

STEP 5

Adjust the tilt and swivel. Remove the plastic cover and use the Allen Key (k) to adjust swivel joint

tension. Remove the plastic cover then use the wrench (l) to tighten the side tilt joints if the monitors

are not fully supported. Tighten the grub screw on back of center monitor joint if the monitor is not

fully supported.

STEP 6

STEP 7

Turn the bolt on the center of the monitor arm counter-clockwise to lower the center monitor or clock-

wise to raise the center monitor. Remove the security nut (s) and turn the bolt underneath with the

Allen Key (k) to raise or lower the side monitor. Replace the nut aer adjustment.

Manage cables for side monitors using the Cable Clips. Cables can also be hidden inside the pole.

Pry off the

Plastic Cap

grub screw

LAST UPDATED: 03/05/2020

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected]

AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Vivo STAND-V003FG Assembly Instructions

Vivo STAND-V003FG Assembly Instructions

Vivo STAND-V003FG Assembly Instructions

Related papers

Other documents